Processing and Creep Performance of Silicon Carbide Whisker-Reinforced Silicon Nitride

1986 ◽  
Vol 78 ◽  
Author(s):  
John. R. Porter ◽  
F. F. Lange ◽  
A. H. Chokshi
Keyword(s):  
Silicon Carbide ◽  
High Temperature ◽  
Silicon Nitride ◽  
Room Temperature ◽  
Full Density ◽  
X Ray Diffraction ◽  
Polycrystalline Alumina ◽  
Silicon Carbide Whisker ◽  
Transmission Electron ◽  
Composite Silicon

ABSTRACTSilicon carbide whisker reinforcement can significantly reduce creep rates in polycrystalline alumina [1], but the system SiC/Al2O3 is thermodynamically unstable in air and oxidizes to mullite during creep testing [2]. The system SiC/Si3N4 was investigated as a potentially more stable, high temperature structural composite. Silicon carbide whiskers were successfully incorporated into a silicon nitride matrix doped with alumina and yttria. Processing involved mixing dispersed slurries of silicon carbide and silicon nitride, adding the dopants as a solution of their nitrates and subsequently increasing the pH to precipitate the additive hydroxides. The resulting slurries were filter pressed at room temperature and hot pressed at 1650°C in graphite dies to full density. X-ray diffraction and transmission electron microscopy confirmed the presence of β-Si3N4, α-SiC and trace quantities of α-Si3N4, confirming that the α-β Si3N4 reaction occurred. An additional, as yet unidentified, minor phase was also detected.Whisker reinforcement was shown to increase the room temperature flexural strength and fracture toughness but high temperature creep performance was unaffected by whisker reinforcement.

Decoration of silicon carbide nanotubes by CoFe2O4 Spinel nanoparticles.

2000 ◽  
Vol 658 ◽  
Author(s):  
Claude Estournès ◽  
Cuong Pham-Huu ◽  
Nicolas Keller ◽  
Marc J. Ledoux
Keyword(s):  
Magnetic Field ◽  
Silicon Carbide ◽  
Room Temperature ◽  
Incipient Wetness Impregnation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Silicon Carbide Nanotubes ◽  
Transmission Electron ◽  
The Magnetic Field ◽  
Spinel Nanoparticles

ABSTRACTSilicon carbide nanotubes have been prepared and decorated with CoFe2O4 spinel. These nanocomposites were prepared by incipient wetness impregnation of the dried SiC support with a stoichiometric aqueous solution of the cobalt and iron nitrates. After drying, subsequent annealing treatments were performed under air in the temperature range 873 to 1073 K. X-ray diffraction and high resolution transmission electron microscopy reveal the presence of spinel nanoparticles at the surface of the tubes. Magnetic properties of the nanocomposites show in the magnetic field explored (up to 5 T) that saturation magnetization is not observed neither at room temperature nor at 5Kelvin. The nanometric character and the nature of the spinel particles are also confirmed by the coercive field (1.6 T) observed at low temperature and the curie temperature.

Mechanical Alloying Behavior in the Nb-Si, Ta-Si, and Nb-Ta-Si Systems

1988 ◽  
Vol 133 ◽  
Author(s):  
K. S. Kumar ◽  
S. K. Mannan
Keyword(s):  
High Temperature ◽  
Mechanical Alloying ◽  
Mechanical Milling ◽  
Room Temperature ◽  
Crystalline Compound ◽  
X Ray Diffraction ◽  
X Ray ◽  
Β Phase ◽  
Α Phase

ABSTRACTThe mechanical alloying behavior of elemental powders in the Nb-Si, Ta-Si, and Nb-Ta-Si systems was examined via X-ray diffraction. The line compounds NbSi2 and TaSi2 form as crystalline compounds rather than amorphous products, but Nb5Si3 and Ta5Si3, although chemically analogous, respond very differently to mechanical milling. The Ta5Si3 composition goes directly from elemental powders to an amorphous product, whereas Nb5Si3 forms as a crystalline compound. The Nb5Si3 compound consists of both the tetragonal room-temperature α phase (c/a = 1.8) and the tetragonal high-temperature β phase (c/a = 0.5). Substituting increasing amounts of Ta for Nb in Nb5Si3 initially stabilizes the α-Nb5Si3 structure preferentially, and subsequently inhibits the formation of a crystalline compound.

Photoluminescence Enhancement of CdS Nanocrystals Fabricated on Dithiocarbamate Functionalized PET Substrates

2012 ◽  
Vol 512-515 ◽  
pp. 1511-1515
Author(s):  
Chun Lin Zhao ◽  
Li Xing ◽  
Xiao Hong Liang ◽  
Jun Hui Xiang ◽  
Fu Shi Zhang ◽  
...  
Keyword(s):  
Room Temperature ◽  
Hexagonal Structure ◽  
Diffraction Measurement ◽  
X Ray Diffraction ◽  
Visible Absorption ◽  
X Ray ◽  
Cds Nanocrystals ◽  
Morphological Studies ◽  
Transmission Electron

Cadmium sulfide (CdS) nanocrystals (NCs) were self-assembled and in-situ immobilized on the dithiocarbamate (DTCs)-functionalized polyethylene glycol terephthalate (PET) substrates between the organic (carbon disulfide diffused in n-hexane) –aqueous (ethylenediamine and Cd2+ dissolved in water) interface at room temperature. Powder X-ray diffraction measurement revealed the hexagonal structure of CdS nanocrystals. Morphological studies performed by scanning electron microscopy (SEM) and high-resolution transmission electron microscope (HRTEM) showed the island-like structure of CdS nanocrystals on PET substrates, as well as energy-dispersive X-ray spectroscopy (EDS) confirmed the stoichiometries of CdS nanocrystals. The optical properties of DTCs modified CdS nanocrystals were thoroughly investigated by ultraviolet-visible absorption spectroscopy (UV-vis) and fluorescence spectroscopy. The as-prepared DTCs present intrinsic hydrophobicity and strong affinity for CdS nanocrystals.

scholarly journals Facile Organometallic Synthesis of Fe-Based Nanomaterials by Hot Injection Reaction

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1141
Author(s):  
Georgia Basina ◽  
Hafsa Khurshid ◽  
Nikolaos Tzitzios ◽  
George Hadjipanayis ◽  
Vasileios Tzitzios
Keyword(s):  
Room Temperature ◽  
Colloidal Particles ◽  
Iron Pentacarbonyl ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
Organometallic Synthesis ◽  
X Ray ◽  
Transmission Electron ◽  
Hot Injection ◽  
The Stability

Fe-based colloids with a core/shell structure consisting of metallic iron and iron oxide were synthesized by a facile hot injection reaction of iron pentacarbonyl in a multi-surfactant mixture. The size of the colloidal particles was affected by the reaction temperature and the results demonstrated that their stability against complete oxidation related to their size. The crystal structure and the morphology were identified by powder X-ray diffraction and transmission electron microscopy, while the magnetic properties were studied at room temperature with a vibrating sample magnetometer. The injection temperature plays a very crucial role and higher temperatures enhance the stability and the resistance against oxidation. For the case of injection at 315 °C, the nanoparticles had around a 10 nm mean diameter and revealed 132 emu/g. Remarkably, a stable dispersion was created due to the colloids’ surface functionalization in a nonpolar solvent.

Structural, Morphological, Magnetic and Self-Heating Studies of One-Step Polyol Synthesized Manganese Ferrite (MnFe2O4) Nanoparticles

2019 ◽  
Vol 19 (01) ◽  
pp. 1950003
Author(s):  
P. R. Ghutepatil ◽  
S. H. Pawar
Keyword(s):  
Room Temperature ◽  
Synthesis Method ◽  
Average Crystallite Size ◽  
Superparamagnetic Nanoparticles ◽  
Polyol Synthesis ◽  
X Ray Diffraction ◽  
Self Heating ◽  
Transmission Electron ◽  
One Step ◽  
Mnfe2o4 Nanoparticles

In this paper, uniform and superparamagnetic nanoparticles have been prepared using one-step polyol synthesis method. Structural, morphological and magnetic properties of obtained MnFe2O4 nanoparticles have been investigated by using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), vibrating sample magnetometry (VSM) and thermogravimetric analysis (TGA) techniques. Structural investigation showed that the average crystallite size of obtained nanoparticles was about 10[Formula: see text]nm. Magnetic study revealed that the nanoparticles were superparamagnetic at room temperature with magnetization 67[Formula: see text]emu/g at room temperature. The self-heating characteristics of synthesized MnFe2O4 nanoparticles were studied by applying external AC magnetic field of 167.6 to 335.2[Formula: see text]Oe at a fixed frequency of 265[Formula: see text]kHz. The SAR values of MnFe2O4 nanoparticles were calculated for 2, 5, 10[Formula: see text]mg[Formula: see text]mL[Formula: see text] concentrations and it is observed that the threshold hyperthermia temperature is achieved for all concentrations.

Silicon Carbide Die Attach Scheme for 500°C Operation

2000 ◽  
Vol 622 ◽  
Author(s):  
Liang-Yu Chen ◽  
Gary W. Hunter ◽  
Philip G. Neudeck
Keyword(s):  
Silicon Carbide ◽  
High Temperature ◽  
Electrical Resistance ◽  
Room Temperature ◽  
Semiconductor Devices ◽  
Single Crystal Silicon ◽  
Film Material ◽  
Crystal Silicon ◽  
Pure Alumina ◽  
Die Attach

ABSTRACTSingle crystal silicon carbide (SiC) has such excellent physical, chemical, and electronic properties that SiC based semiconductor electronics can operate at temperatures in excess of 600°C well beyond the high temperature limit for Si based semiconductor devices. SiC semiconductor devices have been demonstrated to be operable at temperatures as high as 600°C, but only in a probe-station environment partially because suitable packaging technology for high temperature (500°C and beyond) devices is still in development. One of the core technologies necessary for high temperature electronic packaging is semiconductor die-attach with low and stable electrical resistance. This paper discusses a low resistance die-attach method and the results of testing carried out at both room temperature and 500°C in air. A 1 mm2 SiC Schottky diode die was attached to aluminum nitride (AlN) and 96% pure alumina ceramic substrates using precious metal based thick-film material. The attached test die using this scheme survived both electronically and mechanically performance and stability tests at 500°C in oxidizing environment of air for 550 hours. The upper limit of electrical resistance of the die-attach interface estimated by forward I-V curves of an attached diode before and during heat treatment indicated stable and low attach-resistance at both room-temperature and 500°C over the entire 550 hours test period. The future durability tests are also discussed.

Synthesis and Photoluminescence Properties of Novel SnO2 Zigzag Nanoribbons

2010 ◽  
Vol 97-101 ◽  
pp. 4213-4216
Author(s):  
Jian Xiong Liu ◽  
Zheng Yu Wu ◽  
Guo Wen Meng ◽  
Zhao Lin Zhan
Keyword(s):  
Electron Microscopy ◽  
Room Temperature ◽  
Vapour Deposition ◽  
Chemical Vapour ◽  
Photoluminescence Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Ceramic Boat

Novel single-crystalline SnO2 zigzag nanoribbons have been successfully synthesized by chemical vapour deposition. Sn powder in a ceramic boat covered with Si plates was heated at 1100°C in a flowing argon atmosphere to get deposits on a Si wafers. The main part of deposits is SnO2 zigzag nanoribbons. They were characterized by means of X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM) and selected-area electron diffraction (SAED). SEM observations reveal that the SnO2 zigzag nanoribbons are almost uniform, with lengths near to several hundred micrometers and have a good periodically tuned microstructure as the same zigzag angle and growth directions. Possible growth mechanism of these zigzag nanoribbons was discussed. A room temperature PL spectrum of the zigzag nanoribbons shows three peaks at 373nm, 421nm and 477nm.The novel zigzag microstructures will provide a new candidate for potential application.

Sign in / Sign up

Export Citation Format

Share Document