UV Curable Polymers with Organically Modified Clay as the Nanoreinforcements

2003 ◽  
Vol 788 ◽  
Author(s):  
Fawn M. Uhl ◽  
Brian R. Hinderliter ◽  
Siva Prashanth Davuluri ◽  
Stuart G. Croll ◽  
Shing-Chung Wong ◽  
...  
Keyword(s):  
Glass Transition ◽  
Uv Curing ◽  
Barrier Properties ◽  
Clay Nanocomposites ◽  
X Ray Diffraction ◽  
Melt Mixing ◽  
Uv Curable ◽  
Organically Modified ◽  
Transition Barrier

ABSTRACTUV curable polymers are prevalent in microelectronic applications. Several advantages are associated with UV curing such as rapid cure, solvent free systems, application versatility, low energy requirements, and low temperature operation. To be used in electronics the films must posses the following attributes: high glass transition, barrier properties, low shrinkage, flexibility, and enhanced mechanical properties. The area of polymer-clay nanocomposites have been widely investigated by researchers and improved mechanical, thermal, and barrier properties were reported. Most researchers have attempted nanocomposite formation by melt mixing or in situ polymerization. Little is understood on UV curable nanocomposites. This paper seeks to examine nanoclay-containing polymers using organomodified montmorillonites in UV curable systems and the effects of such clay inclusions on the properties of UV cured films. By x-ray diffraction it appeared that intercalated structures were formed. In the case of an epoxy acrylate formulation an increase in glass transition temperature was observed for formulations containing clay.

Irradiation of poly(vinyl ester)/clay nanocomposites

2017 ◽  
Vol 52 (1) ◽  
pp. 17-25 ◽  
Author(s):  
Ahmad Mohaddespour ◽  
Seyed J Ahmadi ◽  
Hossein Abolghassemi ◽  
Seyed M Mahjoub ◽  
Saeid Atashrouz
Keyword(s):  
Vinyl Ester ◽  
In Situ Polymerization ◽  
Surface Hardness ◽  
Clay Nanocomposites ◽  
Mechanical And Thermal Properties ◽  
X Ray Diffraction ◽  
Transition Electron Microscopy ◽  
Organically Modified ◽  
Polymerization Method

The effect of electron beam irradiation on pristine poly(vinyl ester) and cured poly(vinyl ester)/clay nanocomposite with different clay contents is studied at irradiation doses ranging from 100 to 1000 kGy at room temperature. Poly(vinyl ester)/clay nanocomposites were prepared with different amounts of organically modified montmorillonite (1, 3, and 5 wt.%) by in situ polymerization method. Morphology properties of synthesized nanocomposites were studied by X-ray diffraction and transition electron microscopy. The irradiation dose up to 500 kGy yields an increase in Young’s modulus and tensile strength of nanocomposites while further irradiation deteriorates the mechanical strength of samples. Irradiation has no considerable influence on the surface hardness of synthesized nanocomposites. Thermogravimetric analysis results reveal the thermal stability of poly(vinyl ester), and its nanocomposites is improved with irradiation up to 500 kGy. However, similar to mechanical perdition at 1000 kGy irradiation, thermal resistance of nanocomposites decreases. The enhancement in mechanical and thermal properties of synthesized nanocomposites is attributed to the cross-linking effect as bonds can be formed directly between the neighbouring chains.

Natural nanoclays: applications and future trends – a Chilean perspective

Clay Minerals ◽  
2009 ◽  
Vol 44 (2) ◽  
pp. 161-176 ◽  
Author(s):  
M. Calabi Floody ◽  
B. K. G. Theng ◽  
P. Reyes ◽  
M. L. Mora
Keyword(s):  
Agricultural Land ◽  
Clay Fraction ◽  
Barrier Properties ◽  
Clay Nanocomposites ◽  
Volcanic Soils ◽  
Gas Barrier ◽  
Important Species ◽  
The Past ◽  
Organically Modified ◽  
Water And Wastewater

AbstractBecause of their large potential for agricultural, industrial and medicinal applications, nanomaterials have been the focus of much research during the past few decades. Nanoclays are natural nanomaterials that occur in the clay fraction of soil, among which montmorillonite and allophane are the most important species. Montmorillonite is a crystalline hydrous phyllosilicate (layer silicate). Organically-modified montmorillonites or ‘organoclays’, formed by intercalation of quaternary ammonium cations, have long been used as rheological modifiers and additives in paints, inks, greases and cosmetics and as carriers and delivery systems for the controlled release of drugs. Perhaps the largest single usage of organoclays over recent years has been in the manufacture of polymer-clay nanocomposites. These organic–inorganic hybrid materials show superior mechanical, thermal and gas-barrier properties. Organoclays are also useful in pollution control and water treatment. Allophane is a non-crystalline aluminosilicate derived from the weathering of volcanic ash. A large proportion of the agricultural land in Chile is covered by volcanic soils,the clay fraction of which is dominated by allophane. Consisting of nanosize (3.5–5.0 nm) hollow spherules, allophane is a suitable support material for enzyme immobilization. Allophane is also effective at adsorbing phenolic compounds and colour from kraft mill effluents and phosphate from water and wastewater.

Preparation and Characterization of Ionic Liquild Modified Clay and its Application in Polypropylene/Clay Nanocomposites

2011 ◽  
Vol 55-57 ◽  
pp. 1588-1592
Author(s):  
Li Mei Wang
Keyword(s):  
Clay Nanocomposites ◽  
X Ray Diffraction ◽  
Modified Clay ◽  
Solution Blending ◽  
Organically Modified ◽  
Result Show ◽  
Xrd Patterns ◽  
Clay Layers ◽  
Poly Propylene

Clay was organically modified with one kind of ionic liquild. Organical clay obtained was used to prepare poly(propylene) (PP)/clay nanocomposites by solution blending. Flourier transform infrared (FTIR), wide-angle X-ray diffraction (XRD) and thermogravimetric analysis (TGA) revealed that the ionic liquild was loaded in the galleries of organically modified clay. TGA result show the thermal stability of organically modified clay was superior to clay. XRD patterns indicated that the d-spacing of clay layers increased to 2.96 nm from 1.22 nm of clay. XRD patterns of PP/clay nanocomposites show that clay layers were dispersed in PP matrix by nanometer size.

scholarly journals X-Ray Single Crystal Structural Analysis of Magnetically Oriented Microcrystals

2014 ◽  
Vol 70 (a1) ◽  
pp. C1138-C1138
Author(s):  
Chiaki Tsuboi ◽  
Kazuki Aburaya ◽  
Shingo Higuchi ◽  
Fumiko Kimura ◽  
Masataka Maeyama ◽  
...  
Keyword(s):  
Molecular Structure ◽  
Crystal Structure ◽  
Single Crystal ◽  
Three Dimensional ◽  
Diffraction Measurement ◽  
X Ray Diffraction ◽  
Data Set ◽  
Uv Curable ◽  
X Ray

We have developed magnetically oriented microcrystal array (MOMA) technique that enables single crystal X-ray diffraction analyses from microcrystalline powder. In this method, microcrystals suspended in a UV-curable monomer matrix are there-dimensionally aligned by special rotating magnetic field, followed by consolidation of the matrix by photopolymerization. From thus achieved MOMAs, we have been succeeded in crystal structure analysis for some substances [1, 2]. Though MOMA method is an effective technique, it has some problems as follows: in a MOMA, the alignment is deteriorated during the consolidation process. In addition, the sample microcrystals cannot be recovered from a MOMA. To overcome these problems, we performed an in-situ X-ray diffraction measurement using a three-dimensional magnetically oriented microcrystal suspension (3D MOMS) of L-alanine. An experimental setting of the in-situ X-ray measurement of MOMS is schematically shown in the figure. L-alanine microcrystal suspension was poured into a glass capillary and placed on the rotating unit equipped with a pair of neodymium magnets. Rotating X-ray chopper with 10°-slits was placed between the collimator and the suspension. By using this chopper, it was possible to expose the X-ray only when the rotating MOMS makes a specific direction with respect to the impinging X-ray. This has the same effect as the omega oscillation in conventional single crystal measurement. A total of 22 XRD images of 10° increments from 0° to 220° were obtained. The data set was processed by using conventional software to obtain three-dimensional molecular structure of L-alanine. The structure is in good agreement with that reported for the single crystal. R1 and wR2 were 6.53 and 17.4 %, respectively. RMSD value between the determined molecular structure and the reported one was 0.0045 Å. From this result, we conclude that this method can be effective and practical to be used widely for crystal structure analyses.

Microstructure and Mechanical Properties of In Situ TiB2/6061 Composites

2012 ◽  
Vol 535-537 ◽  
pp. 14-17
Author(s):  
Long Hua Zhong ◽  
Yu Tao Zhao ◽  
Song Li Zhang ◽  
Rong Wen
Keyword(s):  
Master Alloy ◽  
Volume Fraction ◽  
X Ray Diffraction ◽  
Melt Mixing ◽  
X Ray ◽  
Mixing Method ◽  
Particulate Volume Fraction ◽  
Ti Powder ◽  
Particulate Volume

In situ TiB2/6061 composites have been successfully synthesized through chemical reaction between 6061 master alloy, Al-3B master alloy and Ti powder. The composites fabricated by direct melt mixing method was investigated by Scanning Electron Microscope (SEM), Energy Dispersive x-ray Spectroscopy (EDS) and X-Ray Diffraction (XRD), The results shown the existence of TiB2particles. The size of most TiB2particles were just in micron level, and even reached to sub-micron level. The increase in microhardness and tensile strength for the as-prepared composites with 5% particulate volume fraction (PVF) are up to 26.8% and 51.2% respectively.

Millable Polyurethane/Organoclay Nanocomposites: Preparation, Characterization, and Properties

2007 ◽  
Vol 7 (2) ◽  
pp. 634-640 ◽  
Author(s):  
M. Siliani ◽  
M. A. López-Manchado ◽  
J. L. Valentín ◽  
M. Arroyo ◽  
A. Marcos ◽  
...  
Keyword(s):  
Barrier Properties ◽  
Substantial Improvement ◽  
Nanometer Scale ◽  
X Ray Diffraction ◽  
Transformation Techniques ◽  
Covalent Bonds ◽  
X Ray ◽  
Transmission Electron ◽  
Organically Modified ◽  
Diffraction Patterns

Novel millable polyurethane (PU)/organoclay nanocomposites have been successfully prepared by conventional transformation techniques. One natural (C6A) and two organically modified (C15A and C30B) montmorillonites have been used as clays for preparing PU nanocomposites. The optimum dispersion of nanofiller at a nanometer scale in PU matrix was confirmed by X-ray diffraction patterns and transmission electron microscopy. A substantial improvement of the PU properties by addition of only a small amount of organoclay was observed. It is worthy to note that the organoclays show a different interfacial interaction with the PU matrix, which was reflected in different macroscopic properties. Thus, C30B organoclay seems to react with PU chains to form covalent bonds, while C15Aonly interacts physically with PU chains. Mechanical and barrier properties are analyzed.

Synthesis and Electrorheological Characteristics of Conducting Polymer/Clay Nanocomposites

2007 ◽  
Vol 124-126 ◽  
pp. 1083-1086
Author(s):  
Jun Hee Sung ◽  
Hyoung Jin Choi
Keyword(s):  
Conducting Polymer ◽  
Electrorheological Fluid ◽  
Clay Nanocomposites ◽  
Wide Angle ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Internal Structures ◽  
In Situ Emulsion Polymerization

Nanocomposites of conducting polymers of polyaniline (PANI), poly(oethoxyaniline) (PEOA) and polypyrrole (PPy) with clay prepared via either in-situ emulsion polymerization or solvent intercalation were investigated especially for electrorheological fluid (ER) application. Internal structures of these nanocomposites were examined via wide angle X-ray diffraction (WAXD), and transmission electron microscope (TEM). The intercalated nanostructures analyzed via WAXD and TEM were correlated with the electrical property change originated from the nanoscale interaction between clay and conducting polymer. Moreover, their ER behaviors were measured via rotational rheometer with external electric field controller.

Modification of clays with styrenic ionic liquid by Synthesis of in-situ Polystyrene Nanocomposite

e-Polymers ◽  
2013 ◽  
Vol 13 (1) ◽  
Author(s):  
Mohammad Galehassadi ◽  
Fatemeh Hosseinzadeh ◽  
Mehrdad Mahkam
Keyword(s):  
Electron Microscopy ◽  
Ionic Liquid ◽  
Clay Nanocomposites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Modified Montmorillonite ◽  
Transmission Electron ◽  
Insitu Polymerization ◽  
Thermal Stability Of

Abstract Nanocomposites of polystyrene (PS) was prepared with new styrenic ionic liquid, N-(4-vinyl benzyl)-(N,N-dimethylamino) pyridinium chloride[VBMAP], surfactants used as organic modifications for the clays. Sodium montmorillonite (Na-MMT) was successfully modified by [VBMAP] to become OMMT through cation exchange technique which is shown by the increase of basalspacing of clay by XRD. The composite material based on polystyrene and organo-modified montmorillonite (OMMT) was prepared by insitu polymerization and characterized. The morphology of the polymer/clay hybrids was evaluated by X-ray diffraction (XRD) ,transmission electron microscopy (TEM) and scanning electron microscopy (SEM), showing good overall dispersion of the clay. The thermal stability of the polymer/clay nanocomposites were enhanced, as evaluated by thermogravimetric analysis.

PREPARATION AND PROPERTIES OF A NOVEL EPOXIDIZED CASTOR OIL/CLAY NANOCOMPOSITES

2004 ◽  
Vol 03 (04n05) ◽  
pp. 663-669 ◽  
Author(s):  
S.-J. PARK ◽  
F.-L. JIN ◽  
J.-R. LEE
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Mechanical Analysis ◽  
Clay Nanocomposites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tearing Energy ◽  
And Storage ◽  
Epoxidized Castor Oil

A novel nanocomposites of modified clay in a glassy epoxy were prepared using a direct melt intercalation technique. The contents of oganoclay were varied with 0, 1, 2, and 3 wt% and N-benzylpyrazinium hexafluoroantimonate (BPH) was used for curing of epoxy matrix as a cationic latent catalyst. Dynamic mechanical analysis (DMA) measurement was performed to examine the glass transition temperature of the nanocomposites. As a result, X-ray diffraction indicated the intercalation of the epoxy chains happening inside the gallery of clay. The nanocomposites showed a higher glass transition temperature and storage modulus than those of the pristine epoxy. The mechanical interfacial properties of the nanocomposites were also investigated and the improvement in tearing energy of 160% over pristine epoxy was obtained.

The Preparation and Characterization of a Novolac Cured Epoxy-Clay Nanocomposites

2006 ◽  
Vol 939 ◽  
Author(s):  
Tsung-Yen Tsai ◽  
Shau-Tai Lu ◽  
Chih-Hung Li ◽  
Chin-Jei Huang ◽  
Li-Chun Chen ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Benzalkonium Chloride ◽  
Barrier Properties ◽  
Layered Silicates ◽  
Clay Nanocomposites ◽  
Crosslinking Reaction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

ABSTRACTIntercalated or exfoliated nanocomposites were composed by the novolac cured epoxy and one of three different kinds of layered silicates, such as montmorillonite (PK-802), saponite (Semecton-SA) and nontronite (PK-805). The bi-functional modifiers (PI/BEN or MI/BEN) with different ratio, which contained one of the promoters (2-phenylimidazole, PI and 2-methylimidazole, MI) of epoxy and benzalkonium chloride (BEN), were intercalated into the gallery regions of pure clays at the same time and followed by a crosslinking reaction. The properties of novolac cured epoxy/clay nanocomposites were characterized by wild-angle X-ray diffraction (WAXRD), thermal analysis (TGA/DSC), coefficiency of thermal expansion (TMA), mechanical properties (DMA), and transmission electron microscopy (TEM). According to the measurement, these novolac cured epoxy-clay nanocomposites have shown the significant improvement in the thermal, mechanical and barrier properties.

Sign in / Sign up

Export Citation Format

Share Document