Nanostructured strain hardened aluminum-magnesium alloys modified by C60 fullerene obtained by powder metallurgy. Part 1. Effect of magnesium concentration on the structure and phase composition of powders

2020 ◽  
pp. 76-84
Author(s):  
I. A. Evdokimov ◽  
R. R. Khayrullin ◽  
R. Kh. Bagramov ◽  
V. V. Aksenenkov ◽  
S. A. Perfilov ◽  
...  
Keyword(s):  
Phase Composition ◽  
Mechanical Activation ◽  
Structural Phase ◽  
Physical And Mechanical Properties ◽  
Magnesium Concentration ◽  
Scanning Calorimetry ◽  
Composite Powders ◽  
Aluminum Magnesium Alloys ◽  
Average Size ◽  
Powder Metallurgy Part

This paper provides the first part of the study on the magnesium effect on the structural phase composition, physical and mechanical properties of nanostructured aluminum-magnesium composite materials with the composition AlxMgy + 0.3 wt.% C60 fullerene. Composite powders were obtained by the simultaneous mechanical activation of initial materials in a planetary ball mill in an argon atmosphere. It was found that the obtained powders have a complex hierarchical structure made up of 50–200 μm aggregates consisting of 5–10 μm strong high-density agglomerates, which in turn are a combination of nanoscale (30–60 nm) crystallites. It was found that the increase in magnesium concentration in the composite up to 18 wt.% makes it possible to obtain crystallites with an average size of less than 30 nm during mechanical activation, while the size of aggregates is less than 50 μm. The maximum solubility of magnesium in aluminum with a crystallite size of 30–70 nm during mechanical activation was 15 wt.% (17 at.%). Using the differential scanning calorimetry method, it was found that nanostructured composites undergo irreversible structural phase transformations during heat treatment in a temperature range of 250–400 °C: recrystallization, decomposition of the α-solid solution of magnesium in aluminum and formation of intermetallic β-(Al3Mg2), γ-(Al12Mg17) and carbide (Al4C3) phases. In addition, the Raman spectra contain peaks that, according to some sources, correspond to covalent compounds of aluminum with C60 fullerene – aluminum-fullerene complexes. The data obtained will be used in further research to determine parameters for the thermobaric treatment of nanocmposite powder mixtures in order to obtain and test bulk samples.

Nanostructured strain-hardened aluminum-magnesium alloys modified by C60 fullerene obtained by powder metallurgy Part 2. The effect of magnesium concentration on physical and mechanical properties

2020 ◽  
pp. 76-84
Author(s):  
I. A. Evdokimov ◽  
R. R. Khayrullin ◽  
R. Kh. Bagramov ◽  
S. A. Perfilov ◽  
A. A. Pozdnyakov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Phase Composition ◽  
Composite Materials ◽  
Powder Metallurgy ◽  
Physical And Mechanical Properties ◽  
Grain Structure ◽  
Magnesium Concentration ◽  
Mechanically Alloyed ◽  
Aluminum Magnesium Alloys

This paper is intended to continue the studies of magnesium effects on the structural phase composition, physical and mechanical properties of the nanostructured strain-hardened aluminum-magnesium alloys modified with C60 fullerene [1]. Previously obtained mechanically alloyed composite powders [1] were consolidated by direct hot extrusion method. Consolidation parameters were chosen based on previous studies of the structure and phase composition formation during mechanical alloying and heat treatment. It was found that an increase in magnesium concentration improves mechanical properties of extruded nanosructured composite materials, and additives modified by C60 fullerene stabilize the grain structure and slow down decomposition of α solid solution of magnesium in aluminum to 300 °C. Under similar thermobaric treatment Al82Mg18 (AMg18) not modified with C60 demonstrates a reduced α solid solution lattice constant and an increased average crystallite size. These processes are accompanied by sequential formation of γ, β′, and β phases, while γ and β′ are intermediate phases. The grain structure of extruded samples is typical for materials obtained in this way – grains are closely packed, elongated and oriented along the extrusion axis. The grain structure of extruded samples inherits the morphology of mechanically alloyed powders. Thus, mechanical alloying methods followed by intense plastic deformation (extrusion) improved mechanical properties significantly. Materials with ultimate tensile strength of 880 MPa; ultimate bending strength of 1100 MPa; microhardness up to 3300 MPa; and with the same density of 2.4–2.6 g/cm3 were obtained. This result demonstrates the prospects for using powder metallurgy techniques in the production of new nanostructured composite materials modified by C60 fullerene with improved physical and mechanical properties.

scholarly journals Formation of phase composition of Ag-Cu bimetallic nanoparticles obtained by electrical explosion of wires

2020 ◽  
pp. 97-101
Author(s):  
A.V. Pervikov ◽  
◽  
A.S. Lozhkomoev ◽  
O.V. Bakina ◽  
M.I. Lerner ◽  
...  
Keyword(s):  
Phase Composition ◽  
Bimetallic Nanoparticles ◽  
Structural Phase ◽  
Electrical Explosion ◽  
Electric Explosion ◽  
Cu Nanoparticles ◽  
Mass Ratio ◽  
Structural Phase State ◽  
Electrical Explosion Of Wires ◽  
Average Size

In present work we observed structural phase state formation of Ag-Cu nanoparticles by electrical explosive of wires. We observed the formation of bimetallic nanoparticles with a number average size of 75 ... 82 nm by synchronous and nonsynchronous electric explosion of wires. The phase composition of the samples is represented by phases based on solid solutions of copper and silver. The results of the studies allow us to conclude that, using electric explosion of copper and silver wires, bimetallic Ag-Cu nanoparticles with different mass ratio of metals can be obtained.

scholarly journals Characterization of Beeswax, Candelilla Wax and Paraffin Wax for Coating Cheeses

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 261
Author(s):  
Adolfo Bucio ◽  
Rosario Moreno-Tovar ◽  
Lauro Bucio ◽  
Jessica Espinosa-Dávila ◽  
Francisco Anguebes-Franceschi
Keyword(s):  
Physical And Mechanical Properties ◽  
Tensile Tests ◽  
Paraffin Wax ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Absorption Bands ◽  
Dimensional Changes ◽  
Ductile Behavior ◽  
Candelilla Wax

A study on the physical and mechanical properties of beeswax (BW), candelilla wax (CW), paraffin wax (PW) and blends was carried out with the aim to evaluate their usefulness as coatings for cheeses. Waxes were analyzed by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), differential scanning calorimetry (DSC), permeability, viscosity, flexural and tensile tests and scanning electron microscopy. Cheeses were coated with the waxes and stored for 5 weeks at 30 °C. Measured parameters were weight, moisture, occurrence and degree of fractures, and dimensional changes. The crystal phases identified by XRD for the three waxes allowed them to determine the length of alkanes and the nonlinear compounds in crystallizable forms in waxes. FTIR spectra showed absorption bands between 1800 and 800 cm−1 related to carbonyls in BW and CW. In DSC, the onset of melting temperature was 45.5 °C for BW, and >54 °C for CW and PW. Cheeses coated with BW did not show cracks after storage. Cheeses coated with CW and PW showed microcraks, and lost weight, moisture and shrunk. In the flexural and tensile tests, BW was ductile; CW and PW were brittle. BW blends with CW or PW displays a semi ductile behavior. Cheeses coated with BW blends lost less than 5% weight during storage. The best waxes were BW and the blends.

scholarly journals Study on Structure, Thermal Behavior, and Viscoelastic Properties of Nanodiamond-Reinforced Poly (vinyl alcohol) Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1426
Author(s):  
Tomáš Remiš ◽  
Petr Bělský ◽  
Tomáš Kovářík ◽  
Jaroslav Kadlec ◽  
Mina Ghafouri Azar ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Analysis ◽  
Single Step ◽  
Poly Vinyl Alcohol ◽  
Scanning Calorimetry ◽  
X Ray Scattering ◽  
Transmission Electron ◽  
Primary Particles ◽  
Solution Casting Method ◽  
Average Size

In this work, advanced polymer nanocomposites comprising of polyvinyl alcohol (PVA) and nanodiamonds (NDs) were developed using a single-step solution-casting method. The properties of the prepared PVA/NDs nanocomposites were investigated using Raman spectroscopy, small- and wide-angle X-ray scattering (SAXS/WAXS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). It was revealed that the tensile strength improved dramatically with increasing ND content in the PVA matrix, suggesting a strong interaction between the NDs and the PVA. SEM, TEM, and SAXS showed that NDs were present in the form of agglomerates with an average size of ~60 nm with primary particles of diameter ~5 nm. These results showed that NDs could act as a good nanofiller for PVA in terms of improving its stability and mechanical properties.

Investigation of Microstructure and Property of Fe3Al/Al2O3 Composites

2010 ◽  
Vol 150-151 ◽  
pp. 1409-1412 ◽  
Author(s):  
Tao Jiang
Keyword(s):  
Heat Treatment ◽  
Phase Composition ◽  
Mechanical Alloying ◽  
Sintering Process ◽  
Composite Powders ◽  
Al2o3 Composite ◽  
Al2o3 Phase ◽  
The Mean ◽  
Xrd Patterns ◽  
Al2o3 Matrix

The Fe3Al/Al2O3 composites were fabricated by pressureless sintering process. The Fe3Al intermetallics compounds powders were fabricated by mechanical alloying and heat treatment, then the Fe3Al powders and Al2O3 powders were mixed and the Fe3Al/Al2O3 composite powders were prepared, so the Fe3Al/Al2O3 composites were fabricated by sintering process at 1700oC for 2h. The phase composition and microstructure of Fe3Al intermetallics compounds powders produced by mechanical alloying and heat treatment were investigated. The phase composition, microstructure and mechanical properties of the Fe3Al/Al2O3 composites sintered bulks were investigated. The XRD patterns results showed that there existed Fe3Al phase and Al2O3 phase in the sintered composites. The Fe3Al/Al2O3 composites sintered bulks exhibited the homogenous and compact microstructure, the Fe3Al particles were homogenously distributed in the Al2O3 matrix, the mean particles size of Fe3Al intermetallics was about 3-5μm. The Fe3Al/Al2O3 composites exhibited more homogenous and compact microstructure with the increase of Fe3Al content in the Al2O3 matrix. The density and relative density of the Fe3Al/Al2O3 composites increased gradually with the increase of Fe3Al content. The fracture strength and fracture toughness of the Fe3Al/Al2O3 composites increased gradually with the increase of Fe3Al content. The elastic modulus and hardness (HRA) of the Fe3Al/Al2O3 composites decreased gradually with the increase of Fe3Al content.

Heat treatememt effect on microstructure and mechanical properties of precipitation hardening elinvar alloy

2021 ◽  
pp. 68-73
Author(s):  
G.V. Shlyakhova ◽  
◽  
A.V. Bochkareva ◽  
M.V. Nadezhkin ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Phase Composition ◽  
Structural Analysis ◽  
Thermal Treatment ◽  
Precipitation Hardening ◽  
Physical And Mechanical Properties ◽  
Alloy Structure ◽  
Treatment Mode ◽  
Elinvar Alloy

This study presents experimental results of structural analysis, such as phase composition, grains size assessment, strength and hardness of Ni-SPAN-C alloy 902 after various heat treatment modes (hardening and aging for stress relaxation). A thermal treatment mode has been selected to obtain higher physical and mechanical properties of the elinvar alloy. It is shown that the improvement of the alloy structure in thermal treatment occurs due to the thermic stresses, as well as the formation and dissolution of intermetallides.

Sign in / Sign up

Export Citation Format

Share Document