scholarly journals SIMULATION AND ANALYSIS OF DIFFERENT PIEZOELECTRIC MATERIALS IN MEMS CANTILEVER FOR ENERGY HARVESTING

2021 ◽  
Vol 9 (1) ◽  
pp. 1321-1328
Author(s):  
Abdul Aziz Khan J , Shanmugaraja P , Kannan S
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Materials ◽  
Low Frequency ◽  
Lead Zirconate ◽  
Vital Role ◽  
Von Mises Stress ◽  
And Performance ◽  
Von Mises ◽  
Implantable Sensor

MEMS Energy Harvesting(EH) devices are excepted to grow in the upcoming years, due to the increasing aspects of MEMS EH devices in vast applications. In Recent advancements in energy harvesting (EH) technologies wireless sensor devices play a vital role to extend their lifetime readily available in natural resources. In this paper the design of MEMS Cantilever at low frequency (100Hz) with different piezoelectric materials Gallium Arsenide (GaAs), Lead Zirconate Titanate (PZT-8), Tellurium Dioxide (TeO2), Zinc oxide (ZnO) is simulated and performance with different materials are compared. The results are analyzed with various parameters such as electric potential voltage, von mises stress, displacement. The paper discusses the suitability of the piezoelectric material for MEMS fully cochlear implantable sensor application.

scholarly journals Analysis and Comparison of Macro Fiber Composites and Lead Zirconate Titanate (PZT) Discs for an Energy Harvesting Floor

2020 ◽  
Vol 10 (17) ◽  
pp. 5951
Author(s):  
Carlos Quiterio Gómez Muñoz ◽  
Gabriel Zamacola Alcalde ◽  
Fausto Pedro García Márquez
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Materials ◽  
Low Cost ◽  
Clean Energy ◽  
Lead Zirconate ◽  
Piezoelectric Transducers ◽  
Piezoelectric Energy ◽  
Pressure Cycle ◽  
Low Consumption

The main drawback in many electronic devices is the duration of their batteries. Energy harvesting provides a solution for these low-consumption devices. Piezoelectric energy harvesting use is growing because it collects small amounts of clean energy and transforms it to electricity. Synthetic piezoelectric materials are a feasible alternative to generate energy for low consumption systems. In addition to the energy generation, each pressure cycle in the piezoelectric material can provide information for the device, for example, counting the passage of people. The main contribution of this work is to study, build, and test a low-cost energy harvesting floor using piezoelectric transducers to estimate the amount of energy that could be produced for a connected device. Several piezoelectric transducers have been employed and analyzed, providing accurate results.

scholarly journals Soft and Hard Piezoelectric Ceramics for Vibration Energy Harvesting

Crystals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 907
Author(s):  
Xiaodong Yan ◽  
Mupeng Zheng ◽  
Mankang Zhu ◽  
Yudong Hou
Keyword(s):  
Power Generation ◽  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Lead Zirconate ◽  
Vibration Energy ◽  
Vibration Energy Harvesting ◽  
Low Frequencies ◽  
Vibration Energy Harvester

The question as to which piezoelectric composition is favorable for energy harvesting has been addressed in the past few years. However, discussion on this topic continues. In this work, an answer is provided through a feasible method which can be used in selecting piezoelectric material. The energy harvesting behavior of hard (P4 and P8) and soft (P5 and P5H) lead zirconate titanate (PZT) ceramics was investigated. The results show that the maximum piezoelectric voltage coefficient g33 and transduction coefficient d33 × g33 were obtained in P5 ceramic. Meanwhile, the power generation characteristics at low frequencies were compared by the vibration energy harvester with a cantilever beam structure. The results indicate that the energy harvester fabricated by the P5 ceramic with the maximum d33 × g33 values also demonstrated the best power generation characteristics. The results unambiguously demonstrate that the power density and energy conversion efficiency of the energy harvesting devices are dominated by the d33 × g33 value of the piezoelectric materials.

Performance of lead-free piezoelectric materials in cantilever-based energy harvesting devices

2014 ◽  
Vol 03 (02) ◽  
pp. 1450010 ◽  
Author(s):  
Anuruddh Kumar ◽  
Rajeev Kumar ◽  
Vishal S. Chauhan ◽  
Rahul Vaish
Keyword(s):  
Energy Harvesting ◽  
Power Density ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Materials ◽  
Lead Zirconate ◽  
Lead Free ◽  
Frequency Range ◽  
Mean Power ◽  
Piezoelectric Energy ◽  
Energy Harvesting Devices

Energy harvesting is one of the emerging applications of piezoelectric materials. In order to replace conventional lead-based materials with lead-free materials, it is important to evaluate their performance for such applications. In the present study, finite element method-based simulation shows mean power density produced from ( K 0.475 Na 0.475 Li 0.05)( Nb 0.92 Ta 0.05 Sb 0.03) O 3 add with 0.4 wt.% CeO 2 and 0.4 wt.% MnO 2 (KNLNTS) bimorph is 96.64% of lead zirconate titanate ( Pb [ Zr x Ti 1-x] O 3) (PZT) ceramics. Load resistance (R), length of proof mass (Lm) and thickness of host layer (th) are optimized (using genetic algorithm) for maximum power density and tuning the operating frequency range which is near to natural frequency of the structure. The lead-free piezoelectric material KNLNTS has comparable results to that of PZT for piezoelectric energy harvester in the ambient frequency range of 90 Hz to 110 Hz. Results show that KNLNTS ceramics can be potentially used in energy harvesting devices.

Multifunctional composite nanofibers with shape memory and piezoelectric properties for energy harvesting

2020 ◽  
Vol 31 (7) ◽  
pp. 956-966 ◽  
Author(s):  
Xiaoyu Guan ◽  
Hairong Chen ◽  
Hong Xia ◽  
Yaqin Fu ◽  
Yiping Qiu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Shape Memory ◽  
Lead Zirconate Titanate ◽  
Composite Nanofibers ◽  
Piezoelectric Materials ◽  
Lead Zirconate ◽  
Silane Coupling Agents ◽  
Zirconate Titanate ◽  
Shape Memory Effects ◽  
Shape Memory Polyurethane

Although many kinds of flexible piezoelectric materials have been developed, there were few reports on flexible multifunctional nanofibers for energy harvesting. In this study, we prepared multifunctional nanofibers from lead zirconate titanate particles and shape memory polyurethane by electrospinning. The resulting nanofibers had both piezoelectric and shape memory effects. To improve the dispersion, lead zirconate titanate particles were modified by silane coupling agents. The lead zirconate titanate/shape memory polyurethane nanofibers were used to harvest energy from sinusoidal vibrations, and the lead zirconate titanate 80 wt% sample produced voltages of 120.3 mV (peak-to-peak). Taking advantage of the shape memory effect, the lead zirconate titanate/shape memory polyurethane nanofibers can be easily deformed into desired shapes and revealed the potential for realizing energy harvesting in complex structures.

scholarly journals Modeling, Simulation and Performance Analysis of Multichannel Mems Piezoelectric Cantilevers for Cochlear Implantable Module

2021 ◽  
Vol 11 (2) ◽  
pp. 510-530
Author(s):  
J. Abdul Aziz Khan ◽  
P. Shanmugaraja ◽  
S. Kannan
Keyword(s):  
Von Mises Stress ◽  
Frequency Range ◽  
Piezoelectric Cantilever ◽  
Audible Frequency ◽  
And Performance ◽  
Piezoelectric Cantilevers ◽  
Von Mises ◽  
Implantable Sensor ◽  
Complete Frequency ◽  
The Brain

This work presents the enhanced area-efficient Multi-channel MEMS (Micro-Electrical Mechanical System) piezoelectric cantilever device (PCD) for a fully cochlear implantable sensor that works within the audible frequency range of 300-4800 Hz. The sound pressure level (SPL) of 95 dB, 100 dB, and 110 dB input is given in order to resonates the audible frequency range of the device which is placed on the eardrum. This stimulates the auditory nerve via the cochlea to send information to the brain. As a result, the Multi-channel MEMS piezoelectric cantilever device generates the highest potential voltage of 870 mV at 110-dB SPL and is detected under the excitation of 300 Hz. The output parameters such as von Mises stress, displacement, and the complete frequency bandwidth performance are analyzed using COMSOL Multiphysics.

scholarly journals Power-Generation Optimization Based on Piezoelectric Ceramic Deformation for Energy Harvesting Application with Renewable Energy

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2171
Author(s):  
Hyeonsu Han ◽  
Junghyuk Ko
Keyword(s):  
Power Generation ◽  
Renewable Energy ◽  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Ceramic ◽  
Piezoelectric Element ◽  
Piezoelectric Ceramics ◽  
Lead Zirconate ◽  
Piezoelectric Energy

Along with the increase in renewable energy, research on energy harvesting combined with piezoelectric energy is being conducted. However, it is difficult to predict the power generation of combined harvesting because there is no data on the power generation by a single piezoelectric material. Before predicting the corresponding power generation and efficiency, it is necessary to quantify the power generation by a single piezoelectric material alone. In this study, the generated power is measured based on three parameters (size of the piezoelectric ceramic, depth of compression, and speed of compression) that contribute to the deformation of a single PZT (Lead zirconate titanate)-based piezoelectric element. The generated power was analyzed by comparing with the corresponding parameters. The analysis results are as follows: (i) considering the difference between the size of the piezoelectric ceramic and the generated power, 20 mm was the most efficient piezoelectric ceramic size, (ii) considering the case of piezoelectric ceramics sized 14 mm, the generated power continued to increase with the increase in the compression depth of the piezoelectric ceramic, and (iii) For piezoelectric ceramics of all diameters, the longer the depth of deformation, the shorter the frequency, and depending on the depth of deformation, there is a specific frequency at which the charging power is maximum. Based on the findings of this study, PZT-based elements can be applied to cases that receive indirect force, including vibration energy and wave energy. In addition, the power generation of a PZT-based element can be predicted, and efficient conditions can be set for maximum power generation.

Energy Harvesting From Pneumatic Tires Using Piezoelectric Transducers

2008 ◽  
Author(s):  
Farbod Khameneifar ◽  
Siamak Arzanpour
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Ground Surface ◽  
Lead Zirconate ◽  
Electrical Circuit ◽  
Piezoelectric Transducers ◽  
Vehicle Speed ◽  
Mechanical Motion ◽  
The Road ◽  
Optimum Load

The concept of harvesting energy in our surrounding has recently drawn global attention. Harvesting the ambient energy of the deflected tire and convert it to electricity is discussed in this paper. An Elastic pneumatic tire deflects due to the load it carries. This deflection appears as a contact patch to the road surface. Initially, the concept of the tire deflection will be discussed. This deflection is then related to the wasted energy used for deflection. The dependency of this energy to some important parameters such as the tire air pressure, vehicle speed and tire geometry and forces are primarily discussed. To harvest the deflection energy different well established methods are exists. Due to the tire environment, piezoelectric transducers can serve as the best option. Those transducers are traditionally used to produce mechanical motion due to the applied electrical charges. This material is also capable of generating electrical charges by mechanical motion and deflections. For the tire energy harvesting application, the piezoelectric stacks can be mounted inside a tire structure such that electric charge is generated therein as the wheel assembly moves along a ground surface. For this application, lead-zirconate-titanate (PZT) is selected. The PZT inside the tire is modeled as a cantilever beam vibration in its first mode of vibration. The frequency of vibration is calculated based on the car speed, tire size, and PZT stack length. A mathematical model for this energy harvesting application is derived. Based on this model, the optimum load of the electrical circuit is also found. Finally the amount of energy harvested from tire using PZT is calculated. Although this energy is not significantly high, it will be enough to provide power for wireless sensors applications.

Fabrication of Thick, Sol Gel Pzt Films: Applications to Macroscopic Piezoelectric Devices

1994 ◽  
Vol 360 ◽  
Author(s):  
D.A. Barrow ◽  
T.E. Petroff ◽  
M. Sayer
Keyword(s):  
Lead Zirconate Titanate ◽  
Sol Gel ◽  
Low Frequency ◽  
Lead Zirconate ◽  
Resonant Vibrations ◽  
Pzt Film ◽  
Sol Gel Process ◽  
Pzt Films ◽  
High Frequency Resonance ◽  
Piezoelectric Devices

AbstractLead zirconate titanate (PZT) films of up to 60 μm in thickness have been fabricated on a wide variety of substrates using a new sol gel process. The dielectric properties (∈ = 900), ferroelectric (Ec = 16 kV/cm and Pr = 35 μC/cm 2) and piezoelectric properties are comparable to bulk values. The characteristic Curie point of these films is at 420 °C. Piezoelectric actuators have been developed by depositing thick PZT films on both planar and coaxial substrates. Stainless steel cantilevers and optical fibres coated with a PZT film exhibit flexure mode resonant vibrations observable with the naked eye. A low frequency in-line fibre optic modulator has been developed using a PZT coated optical fibre. The high frequency resonance of a 60 μm film on a aluminum substrate has been observed.

Study of Cantilever Structures Based on Piezoelectric Materials for Energy Harvesting at Low Frequency of Vibration

2014 ◽  
Vol 976 ◽  
pp. 159-163 ◽  
Author(s):  
Roberto Ambrosio ◽  
Hector Gonzalez ◽  
Mario Moreno ◽  
Alfonso Torres ◽  
Rafael Martinez ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Lead Zirconate Titanate ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electrical Contacts ◽  
Piezoelectric Energy Harvesting ◽  
Maximum Output ◽  
Coupling Coefficients ◽  
Piezoelectric Energy

In this work is presented a study of a piezoelectric energy harvesting device used for low power consumption applications operating at relative low frequency. The structure consists of a cantilever beam made by Lead Zirconate Titanate (PZT) layer with two gold electrodes for electrical contacts. The piezoelectric material was selected taking into account its high coupling coefficients. Different structures were analyzed with variations in its dimensions and shape of the cantilever. The devices were designed to operate at the resonance frequency to get maximum electrical power output. The structures were simulated using finite element (FE) software. The analysis of the harvesting devices was performed in order to investigate the influence of the geometric parameters on the output power and the natural frequency. To validate the simulation results, an experiment with a PZT cantilever with brass substrate was carried out. The experimental data was found to be very close to simulation data. The results indicate that large structures, in the order of millimeters, are the ideal for piezoelectric energy harvesting devices providing a maximum output power in the range of mW

Sign in / Sign up

Export Citation Format

Share Document