scholarly journals Effect of Fiber on Residual Strength and High Temperature Burst Performance of Ultra High Performance Concrete

2021 ◽  
pp. 224-231
Author(s):  
Huijie Shang, Qianqian Peng
Keyword(s):  
Compressive Strength ◽  
High Temperature ◽  
Mass Loss ◽  
Ultrasonic Wave ◽  
Wave Velocity ◽  
Residual Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Ultra High Performance Concrete ◽  
Burst Performance

In this paper, the effects of fiber on the residual strength and high temperature burst performance of ultra-high performance concrete are studied. This paper analyzes the performance change law of concrete after high temperature from three aspects: mass loss, ultrasonic wave velocity and compressive strength. The results show that with the increase of heating temperature, the mass loss increases and the ultrasonic wave velocity decreases. The compressive strength of concrete increases gradually before 300 ℃ and decreases gradually after 400 ℃. Mixing PVA fiber and steel fiber can not only improve the burst resistance of ultra-high performance concrete at high temperature, but also have high residual strength. This paper discusses the high temperature burst mechanism of ultra-high performance concrete, which is caused by the change of steam pressure and microstructure.

Study on the Ultra High Performance Concrete Containing Limestone Powder

2011 ◽  
Vol 250-253 ◽  
pp. 686-689 ◽  
Author(s):  
Shu Hua Liu ◽  
Zhi Yang Gao ◽  
Mei Juan Rao
Keyword(s):  
Compressive Strength ◽  
High Temperature ◽  
High Performance ◽  
High Performance Concrete ◽  
Limestone Powder ◽  
Ultra High Performance Concrete ◽  
The Cost

A new kind of ultra high performance concrete containing limestone powder was studied in this paper. The results show that the compressive strength of the ultra high performance concrete containing limestone powder is higher than 120MPa; the hydration activity and the accelerating effect of limestone powder are obvious under the condition of high temperature. The limestone powder hydrated and formed calcium monocaboaluminate hydrates. The cost would be reduced when adding certain amount of limestone powder when confect ultra high performance concrete. It is economical and feasible.

scholarly journals Ultra-high-performance concrete with local high unburned carbon fly ash

DYNA ◽  
2021 ◽  
Vol 88 (216) ◽  
pp. 38-47
Author(s):  
Joaquín Abellán García ◽  
Nancy Torres Castellanos ◽  
Jaime Antonio Fernandez Gomez ◽  
Andres Mauricio Nuñez Lopez
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Performance ◽  
High Performance Concrete ◽  
Unburned Carbon ◽  
High Tech ◽  
Ultra High Performance Concrete ◽  
Conventional Concrete ◽  
The Cost

Ultra-high-performance concrete (UHPC) is a kind of high-tech cementitious material with superb mechanical and durability properties compared to other types of concrete. However, due to the high content of cement and silica fume used, the cost and environmental impact of UHPC is considerably higher than conventional concrete. For this reason, several efforts around the world have been made to develop UHPC with greener and less expensive local pozzolans. This study aimed to design and produce UHPC using local fly ash available in Colombia. A numerical optimization, based on Design of Experiments (DoE) and multi-objective criteria, was performed to obtain a mixture with the proper flow and highest compressive strength, while simultaneously having the minimum content of cement. The results showed that, despite the low quality of local fly ashes in Colombia, compressive strength values of 150 MPa without any heat treatment can be achieved.

scholarly journals Mechanical Properties and Environmental Evaluation of Ultra-High-Performance Concrete with Aeolian Sand

Materials ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3148 ◽  
Author(s):  
Hongyan Chu ◽  
Fengjuan Wang ◽  
Liguo Wang ◽  
Taotao Feng ◽  
Danqian Wang
Keyword(s):  
Compressive Strength ◽  
Environmental Impact ◽  
Young’S Modulus ◽  
High Performance ◽  
High Performance Concrete ◽  
Young's Modulus ◽  
Ultra High Performance Concrete ◽  
Aeolian Sand ◽  
Binder Ratio ◽  
Water Binder Ratio

Ultra-high-performance concrete (UHPC) has received increasing attention in recent years due to its remarkable ductility, durability, and mechanical properties. However, the manufacture of UHPC can cause serious environmental issues. This work addresses the feasibility of using aeolian sand to produce UHPC, and the mix design, environmental impact, and mechanical characterization of UHPC are investigated. We designed the mix proportions of the UHPC according to the modified Andreasen and Andersen particle packing model. We studied the workability, microstructure, porosity, mechanical performance, and environmental impact of UHPC with three different water/binder ratios. The following findings were noted: (1) the compressive strength, flexural strength, and Young’s modulus of the designed UHPC samples were in the ranges of 163.9–207.0 MPa, 18.0–32.2 MPa, and 49.3–58.9 GPa, respectively; (2) the compressive strength, flexural strength, and Young’s modulus of the UHPC increased with a decrease in water/binder ratio and an increase in the steel fibre content; (3) the compressive strength–Young’s modulus correlation of the UHPC could be described by an exponential formula; (4) the environmental impact of UHPC can be improved by decreasing its water/binder ratio. These findings suggest that it is possible to use aeolian sand to manufacture UHPC, and this study promotes the application of aeolian sand for this purpose.

The ability of high performance concrete to resist high temperature

2017 ◽  
Vol 8 (4) ◽  
pp. 392-401 ◽  
Author(s):  
Hassan A.M. Mhamoud ◽  
Jia Yanmin
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Mass Loss ◽  
High Performance ◽  
Elevated Temperatures ◽  
High Performance Concrete ◽  
Sharp Decrease ◽  
Test Results ◽  
Content Type ◽  
Chinese Standard

Purpose This study aims to focus on the resistance to elevated temperatures of up to 700ºC of high-performance concrete (HPC) compared to ordinary Portland concrete (OPC) with regards to mass loss and residual compressive and flexural strength. Design/methodology/approach Two mixtures were developed to test. The first mixture, OPC, was used as the control, and the second mixture was HPC. After 28 days under water (per Chinese standard), the samples were tested for compressive strength and residual strength. Findings The test results showed that at elevated temperatures of up to 500ºC, each mixture experienced mass loss. Below this temperature, the strength and the mass loss did not differ greatly. Originality/value When adding a 10 per cent silica fume, 25 per cent fly, 25 per cent slag to HPC, the compressive strength increased by 17 per cent and enhanced the residual compressive strength. A sharp decrease was observed in the residual flexural strength of HPC when compared to OPC after exposure to temperatures of 700ºC.

Material Properties of Ultra - High Performance Concrete in Extreme Conditions

2016 ◽  
Vol 711 ◽  
pp. 157-162 ◽  
Author(s):  
David Citek ◽  
Milan Rydval ◽  
Stanislav Rehacek ◽  
Jiří Kolísko
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Material Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Accurate Information ◽  
Extreme Conditions ◽  
Ultra High Performance Concrete ◽  
Freeze Thaw

The Ultra High Performance Concrete (UHPC) is a very promising material suitable for application in special structures. However, the knowledge of performance of this relatively new material is rather limited. The exceptional mechanical properties of UHPC allow for a modification of the design rules, which are applicable in ordinary or high strength concrete. This paper deals in more detail with impact of thermal stress on bond properties between prestressing strands and UHPC and an influence of high temperature to final material properties of different UHPC mixtures. Specimens in the first experimental part were subjected to the cycling freeze-thaw testing. The relationship between bond behavior of both type of material (UHPC and ordinary concrete) and effect of cycling freeze-thaw tests was investigated. The second part of experimental work was focused on mechanical properties of UHPC exposure to the high temperature (Tmax = 200°C to Tmax = 1000°C). Tested mechanical properties were compressive and flexural strengths, the fracture properties will be presented in the next paper. The obtained experimental data serve as a basis for further systematic experimental verification and more accurate information about the significantly higher material properties of UHP(FR)C and its behavior in extreme conditions.

Contribution of Reinforcing Fiber Types on the Mechanical Properties of High Performance Concrete Subjected to High Temperature

2013 ◽  
Vol 368-370 ◽  
pp. 1052-1055
Author(s):  
Seung Jo Lee ◽  
Jung Min Park
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Temperature ◽  
Weight Reduction ◽  
High Performance ◽  
High Performance Concrete ◽  
Reduction Ratio ◽  
Fiber Types ◽  
Residual Compressive Strength ◽  
Reinforcing Fiber

The aim of the study is to improve the understanding of the influence of reinforcing fiber types on the mechanical properties of high performance concretes (HPC) subjected to high temperature. The mechanical properties measured include residual compressive strength, weight reduction ratio, outward appearance property, and failure mode. Nylon, polypropylene, and steel fiber were added to enhance mechanical property of the concretes. After exposure to high temperatures ranged from 100 to 800°C, mechanical properties of fiber-toughened HPC were investigated. For HPC, although residual compressive strength was decreased by exposure to high temperature over 500°C, weight reduction ratio was significantly higher than that before heating temperature.

Study on the Compressive Strength and Mixing of Ultra-High Performance Concrete

2013 ◽  
Vol 357-360 ◽  
pp. 825-828
Author(s):  
Su Li Feng ◽  
Peng Zhao
Keyword(s):  
Compressive Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Strength Properties ◽  
Test Method ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Ultra High Performance Concrete ◽  
Mixture Ratio

The test in order to obtain liquidity, higher intensity ultra-high performance concrete(UHPC), in the course of preparation, high intensity quartz sand to replace the ordinary sand,reasonable mixture ratio control low water-cement ratio,the incorporation of part of the test piece ofsteel fibers, produced eight specimens . In the ordinary molding and the standard conservation 28d thecase, the ultra-high-performance concrete compressive strength of more than 170MPa.Thepreparation of the test method and test results will provide the basis for further study of the law of themechanical properties of ultra high strength properties of concrete.

Sign in / Sign up

Export Citation Format

Share Document