scholarly journals Research on the stages of the wear of the tip cutting edge with a rounding radius based on the mathematical and geometric model

Mechanik ◽  
2019 ◽  
Vol 92 (11) ◽  
pp. 704-706
Author(s):  
Borys Storch ◽  
Łukasz Żurawski
Keyword(s):  
Geometric Model ◽  
Cutting Tools ◽  
Cutting Edge ◽  
Wear Model ◽  
Machined Surface ◽  
Edge Wear

In modern multiuse cutting tools with exchange plate (e.g. with superfinishing edge or Wiper), the cutting edge is made without documenting the basis for optimizing its dimensions. The article presents a generalized edge wear model surrounded by a rounded tip. The proposed solution allows such a modification of edge corner – by determining the conditions of its work – to adapt the tool to stabilize the process of shaping the machined surface.

scholarly journals Reamers cutting edge preparation for improvement the GGG 40 machining

2018 ◽  
Vol 178 ◽  
pp. 01014
Author(s):  
Ioan-Doru Voina ◽  
Stefan Sattel ◽  
Glad Contiu ◽  
Adrian Faur ◽  
Bogdan Luca
Keyword(s):  
Wear Resistance ◽  
Coating Layer ◽  
Cutting Tools ◽  
Cutting Edge ◽  
Abrasive Jet Machining ◽  
Edge Wear ◽  
Solid Carbide ◽  
Cutting Edge Preparation ◽  
Machining Strategies ◽  
Edge Preparation

The improvement of the microgeometry became a subject of a great interest in cutting tools optimization. This paper approaches the process of cutting edge preparation of solid carbide reamers. It has been analyzed the evolution of cutting edge wear resistance in the material GGG 40 using the scanning electron microscope (SEM). The work also compared the rounded cutting edge reamers realized using wet abrasive jet machining with standard unprepared cutting edge. To obtain different microgeometries were experienced a number of machining strategies, which resulted in four combinations of roundness and forms for the cutting edge. In order to validate the results, the author studied the wear resistance during the reaming tests, the influence of prepared surface of the cutting edge on metallic coating layer adhesion. The final purpose was to determinate the optimal strategy of cutting edge preparation considering the evolution of wear during the reaming process.

Effect of tool wear on chip formation during dry machining of Ti-6Al-4V alloy, part 2: Effect of tool failure modes

2015 ◽  
Vol 231 (9) ◽  
pp. 1575-1586 ◽  
Author(s):  
Shoujin Sun ◽  
Milan Brandt ◽  
Matthew S Dargusch
Keyword(s):  
Plastic Deformation ◽  
Tool Wear ◽  
Failure Modes ◽  
Flank Wear ◽  
Cutting Tools ◽  
Cutting Edge ◽  
Machined Surface ◽  
Tool Failure ◽  
Geometric Ratio ◽  
Cutting Speeds

Variation in the geometric and surface features of segmented chips with an increase in the volume of material removed and tool wear has been investigated at cutting speeds of 150 and 220 m/min at which the cutting tools fail due to gradual flank wear and plastic deformation of the cutting edge, respectively. Among the investigated geometric variables of the segmented chips, slipping angle, undeformed surface length, segment spacing, degree of segmentation and chip width showed the different variation trends with an increase in the volume of material removed or flank wear width, and achieved different values when tool failed at different cutting speeds. However, the chip geometric ratio showed a similar variation trend with an increase in the volume of material removed and flank wear width, and achieved the similar value at the end of tool lives at cutting speeds of both 150 and 220 m/min regardless of the different tool failure modes. Plastic deformation of the tool cutting edge results in severe damage on the machined surface of the chip and significant compression deformation on the undeformed surface of the chip.

On the Influence of the Speed-Feed Interaction on the Wear Rate and Life of Multiple Coated Carbide Inserts Considering Rough Turning Process

2014 ◽  
Vol 575 ◽  
pp. 431-436 ◽  
Author(s):  
M.S. Alajmi ◽  
S.E. Oraby
Keyword(s):  
Wear Rate ◽  
Cutting Speed ◽  
Dimensional Accuracy ◽  
Cutting Edge ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Edge Wear ◽  
The Impact ◽  
Rough Turning ◽  
Coated Carbide

The impact of the cutting parameters; speed, feed, and depth of cut on the wear and the life of the cutting edge has long been a matter of debate among researchers. The cutting speed has long been agreed to have a prime influence in such a way that increasing speed leads to higher wear rate. Depth of cut has been concluded by majority of studies to have insignificant or negligible impact on edge wear and deformation. Despite its long established influence on the roughness of the machined surface, the effect of cutting feed on edge wear and deformation still requires more explanation. Cutting feed is a crucial parameter governing the product surface finish and dimensional accuracy and, therefore, its attitude during machining should be fully understood. This study presents experimental and modeling approach to detect the feed-wear functional interrelation considering various domains of the cutting speed. Results showed that the impact of the cutting feed is firmly associated with the level of cutting speed employed. Speed-feed interaction proved to be responsible for the performance of the cutting edge during machining.

scholarly journals Feasibility of Cobalt-Free Nanostructured WC Cutting Inserts for Machining of a TiC/Fe Composite

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3432
Author(s):  
Edwin Gevorkyan ◽  
Mirosław Rucki ◽  
Tadeusz Sałaciński ◽  
Zbigniew Siemiątkowski ◽  
Volodymyr Nerubatskyi ◽  
...  
Keyword(s):  
Cubic Boron Nitride ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Machined Surface ◽  
Powder Consolidation ◽  
Plasma Sintering ◽  
Cutting Inserts ◽  
Spark Plasma ◽  
And Performance ◽  
Nanostructured Tungsten Carbide

The paper presents results of investigations on the binderless nanostructured tungsten carbide (WC) cutting tools fabrication and performance. The scientific novelty includes the description of some regularities of the powder consolidation under electric current and the subsequent possibility to utilize them for practical use in the fabrication of cutting tools. The sintering process of WC nanopowder was performed with the electroconsolidation method, which is a modification of spark plasma sintering (SPS). Its advantages include low temperatures and short sintering time which allows retaining nanosize grains of ca. 70 nm, close to the original particle size of the starting powder. In respect to the application of the cutting tools, pure WC nanostructure resulted in a smaller cutting edge radius providing a higher quality of TiC/Fe machined surface. In the range of cutting speeds, vc = 15–40 m/min the durability of the inserts was 75% of that achieved by cubic boron nitride ones, and more than two times better than that of WC-Co cutting tools. In additional tests of machining 13CrMo4 material at an elevated cutting speed of vc = 100 m/min, binderless nWC inserts worked almost three times longer than WC-Co composites.

Cutting edge wear in high-speed stainless steel end milling

2021 ◽  
Author(s):  
Mohammad Malekan ◽  
Camilla D. Bloch-Jensen ◽  
Maryam Alizadeh Zolbin ◽  
Klaus B. Ørskov ◽  
Henrik M. Jensen ◽  
...  
Keyword(s):  
Stainless Steel ◽  
High Speed ◽  
End Milling ◽  
Cutting Edge ◽  
Edge Wear

scholarly journals The Comparative Study on Cutting Performance of Different-Structure Milling Cutters in Machining CFRP

2018 ◽  
Vol 8 (8) ◽  
pp. 1353
Author(s):  
Tao Chen ◽  
Fei Gao ◽  
Suyan Li ◽  
Xianli Liu
Keyword(s):  
Carbon Fiber ◽  
Cutting Force ◽  
Surface Quality ◽  
Cutting Edge ◽  
Cutting Performance ◽  
Machining Process ◽  
Carbon Fiber Composites ◽  
Machined Surface ◽  
Milling Cutter ◽  
Machined Surface Quality

Carbon fiber reinforced plastic (CFRP) is typically hard to process, because it is easy for it to generate processing damage such as burrs, tears, delamination, and so on in the machining process. Consequently, this restricts its wide spread application. This paper conducted a comparative experiment on the cutting performance of the two different-structure milling cutters, with a helical staggered edge and a rhombic edge, in milling carbon fiber composites; analyzed the wear morphologies of the two cutting tools; and thus acquired the effect of the tool structure on the machined surface quality and cutting force. The results indicated that in the whole cutting, the rhombic milling cutter with a segmented cutting edge showed better wear resistance and a more stable machined surface quality. It was not until a large area of coating shedding occurred, along with chip clogging, that the surface quality decreased significantly. At the stage of coating wear, the helical staggered milling cutter with an alternately arranged continuous cutting edge showed better machined surface quality, but when the coating fell off, its machined surface quality began to reveal damage such as groove, tear, and fiber pullout. Meanwhile, burrs occurred at the edge and the cutting force obviously increased. By contrast, for the rhombic milling cutter, both the surface roughness and cutting force increased relatively slowly.

What Sound Can Be Expected From a Worn Tool?

1969 ◽  
Vol 91 (3) ◽  
pp. 525-534 ◽  
Author(s):  
E. J. Weller ◽  
H. M. Schrier ◽  
Bjorn Weichbrodt
Keyword(s):  
Machine Tool ◽  
Detection System ◽  
Cutting Edge ◽  
Cemented Carbide ◽  
Electronic Unit ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
Edge Wear ◽  
Sonic Detection ◽  
1045 Steel

This paper describes an electronic-mechanical system which utilizes sonic signals to detect the degree of cutting edge wear in metalworking tools and automatically trigger a cutting edge change. A packaged electronic unit reads out sonic vibrations from an instrumented machine-tool workpiece cutting-tool system to determine degree of cutting edge wear during a turning cut. At a predetermined comparative sonic ratio, the electronic unit commands stoppage of the machine tool feed, retraction of the tool and automatic index of the cemented carbide insert to the next good cutting edge. The latter function is performed by a prototype mechanical device. The paper describes the system and cites data generated during use of the sonic detection system with five grades of cemented carbide cutting AISI 1045 steel. Results under varying cutting conditions are reported. The authors speculate on the possibility of combining such a wear detection and cutting edge indexing arrangement with a computer to provide a complete system for optimum productivity and economy in a completely automatic operation.

Kantenpräparation durch Formschleifprozesse*/Cutting edge preparation by form grinding

2017 ◽  
Vol 107 (06) ◽  
pp. 453-460
Author(s):  
E. Prof. Uhlmann ◽  
J. Bruckhoff
Keyword(s):  
Tool Life ◽  
Cutting Tools ◽  
Cutting Edge ◽  
Grinding Processes ◽  
Form Grinding ◽  
Cutting Edge Preparation ◽  
Edge Preparation

Angesichts steigender Anforderungen an Zerspanwerkzeuge nimmt die Schneidkantenpräparation einen immer größer werdenden Stellenwert ein, da sich so die Standzeit von Zerspanwerkzeugen erhöhen lässt. Die bisher eingesetzten Präparationsverfahren eignen sich meist nur für einfache Verrundungen an der Schneidkante. In umfangreichen Untersuchungen wurde die Eignung von Formschleifprozessen zur Herstellung definierter Schneidkantenmikrogeometrien anhand von Arbeitsergebnissen analysiert.   Due to increasing demands on cutting tools cutting edge preparation has a high priority because it influences the tool life. Current cutting edge preparation processes can only generate simple roundings on the cutting edge. By extensive investigations the suitability of form grinding processes for the production of defined microgeometries on the cutting edge was analysed.

scholarly journals Obtaining Various Shapes of Machined Surface Using a Tool with a Multi-Insert Cutting Edge

2019 ◽  
Vol 9 (5) ◽  
pp. 880 ◽  
Author(s):  
Tadeusz Mikolajczyk ◽  
Danil Pimenov ◽  
Catalin Pruncu ◽  
Karali Patra ◽  
Hubert Latos ◽  
...  
Keyword(s):  
Cutting Edge ◽  
Machined Surface ◽  
Wide Range ◽  
Complex Shapes ◽  
Functional Features ◽  
Tool Set ◽  
The Individual ◽  
Milling Tools ◽  
Novel Design ◽  
Positive Results

A novel design of a universal form tool is presented for machining complex planar and axisymmetric surfaces. The geometric and kinematic flexibility (GKF) of this tool type means that it can machine a wide range of profiles using a single setup. The operating principle of this multi-insert tool is its combination of single cutting edges, each of which form the individual details of the machined surface. The structure and application of both turning and milling multi-insert tools with combinations of single edges are described in the paper. Complex shapes and forms can be machined by changing the cutting-edge positions. The number of combinations of a given tool set can be determined by using the relations detailed in this study. Both turning and milling tools are utilized in a unique tool holder that clamps the inserts into position and allows their adjustment that is facilitated by special prepared analytical software to the desired object profiles. It is possible to use these tools in machining both wood and aluminum alloys. Finally, the design of the multi-insert tools for turning and milling and its functional features were experimentally verified with positive results.

Sign in / Sign up

Export Citation Format

Share Document