scholarly journals CUTTING CERAMIC DURABILITY IN MACHINING PROCESS OF BEARINGS STEEL 100CR6

2016 ◽  
Vol 2016 (04) ◽  
pp. 1060-1065 ◽  
Author(s):  
Anton Panda ◽  
Jan Duplak ◽  
Michal Hatala
Keyword(s):  
Machining Process ◽  
Cutting Ceramic

The Comprehensive Comparison of the Selected Cutting Materials with Standard ISO 3685 in Machining Process of Steel C60

2014 ◽  
Vol 718 ◽  
pp. 93-98 ◽  
Author(s):  
Ján Duplák ◽  
Michal Hatala ◽  
Jozef Zajac ◽  
Karol Vasilko ◽  
Miroslav Kormoš ◽  
...  
Keyword(s):  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Machining Process ◽  
Engineering Practice ◽  
Technical Standards ◽  
Sintered Carbide ◽  
Cutting Ceramic ◽  
Comprehensive Comparison ◽  
Steel Cutting

The main part of Standard ISO 3685 is T-vc dependence for various cutting materials. The Standard ISO 3685 contains main properties and characteristics for three most important cutting materials those are used in engineering practice. These cutting materials are used for cutting tools made of high speed steel, cutting ceramic and sintered carbide. Some types of cutting materials are defined by means of descriptions in standards ISO, some types by means of catalogues from the manufacturer. There are a lot of types of cutting materials they have not been defined theirs properties exactly yet and theirs properties have to be defined on experiments. There is a presumption that descriptions in standards ISO are not correct and these standards have to be examined and verified, because that this fact have to be confirmed or disproved. Accuracy and completeness technical standards ISO are very important part quality of manufacturing. Article describes process how to define T-vc dependence for cutting tools made of high speed steel, cutting ceramic and sintered carbide, because were found deficiencies in valid standard ISO 3685.

Comprehensive Durability Identification of Ceramic Cutting Materials in Machining Process of Steel 80MoCrV4016

2015 ◽  
Vol 669 ◽  
pp. 286-293 ◽  
Author(s):  
Anton Panda ◽  
Ján Duplák ◽  
Miroslav Kormoš ◽  
Juraj Ružbarský
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Machining Process ◽  
Technological Operation ◽  
Technical Science ◽  
Cutting Ceramic ◽  
Comprehensive Information ◽  
Cutting Speeds ◽  
Tool Durability

Specification cutting tools durability made of cutting ceramic in machining process of steel 80MoCrV4016 is very important for economics of small and medium-sized enterprises, because cutting tool durability is factor that significantly affects the budget of these enterprises. This problematic is determined for small and medium-sized manufacturers of bearings, because steel 80MoCrV4016 is most commonly used for production of bearings. Durability of cutting tool defines lifetime of this cutting tool and it determines its suitability for select technological operation. Especially for cutting ceramic is necessary to define durability dependence on available set of cutting speeds and to determine lifetime of tools made of cutting ceramic. Technical science defines a lot of different factors, that they may be cause of shorter cutting tool lifetime. For increase cutting tool durability is necessary maximally possible elimination of these factors. Determination of cutting tool durability is very important, because provides comprehensive information how to determine appropriate technological conditions for selected cutting tool. In engineering is for determination of cutting tools durability usedT-vcdependence. The article describes process how to create durability dependence for cutting tools made of cutting ceramic by means ofT-vcdependence in machining process of steel 80MoCrV4016.

Tapered Roller Bearing and Comprehensive Durability Identification of Ceramic Cutting Materials in Machining Process of Steel 80MoCrV4016

2013 ◽  
Vol 415 ◽  
pp. 606-609
Author(s):  
Anton Panda ◽  
Ján Duplák ◽  
Jozef Jurko
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Roller Bearing ◽  
Machining Process ◽  
Technical Science ◽  
Tapered Roller Bearing ◽  
Cutting Ceramic ◽  
Tapered Roller ◽  
Tool Durability

Specification cutting tools durability made of cutting ceramic in machining process of steel 80MoCrV4016 is very important for economics of small and medium-sized enterprises, because cutting tool durability is factor that significantly affects the budget of these enterprises. This problematic is determined for small and medium-sized manufacturers of bearings, because steel 80MoCrV4016 is most commonly used for production of bearings. Durability of cutting tool defines lifetime of this cutting tool and it determines its suitability for select technological operation. Especially for cutting ceramic is necessary to define durability dependence on available set of cutting speeds and to determine lifetime of tools made of cutting ceramic. Technical science defines a lot of different factors, that they may be cause of shorter cutting tool lifetime. For increase cutting tool durability is necessary maximally possible elimination of these factors. Determination of cutting tool durability is very important, because provides comprehensive information how to determine appropriate technological conditions for selected cutting tool. In engineering is for determination of cutting tools durability used T-vc dependence. The article describes process how to create durability dependence for cutting tools made of cutting ceramic by means of T-vc dependence in machining process of steel 80MoCrV4016.

Analysis of Selected Properties of Cutting Ceramics at Machining Process of Bearing Steel 100Cr6

2014 ◽  
Vol 616 ◽  
pp. 308-316 ◽  
Author(s):  
Anton Panda ◽  
Ján Duplák ◽  
Marek Prislupčák ◽  
Pavol Kokuľa
Keyword(s):  
High Speed ◽  
Cutting Tool ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Bearing Steel ◽  
Machining Process ◽  
Cutting Ceramic ◽  
Cutting Ceramics ◽  
Bearing Rings ◽  
Tool Durability

Cutting tool durability is very important cutting tool property. Especially for cutting ceramic is necessary to define durability dependence on available set of cutting speeds and to determine lifetime of tools made of cutting ceramic. Durability of cutting tools is defined in standard ISO 3685. In standard ISO 3685 is defined T-vc dependence for different cutting materials and standard included process evaluation of tool durability for cutting materials made of high speed steel, sintered carbide and cutting ceramic. Specification cutting tools durability made of cutting ceramic in machining process of steel 100Cr6 is very important for economics of small and medium-sized enterprises, because cutting tool durability is factor that significantly affects the budget of these enterprises. This problematic is determined for small and medium-sized manufacturers of bearings, because steel 100Cr6 is most commonly used for production of bearing rings 100 mm in diameter. This material is usable for actuator (actuators and reduction gears) too. Description of cutting ceramic durability could mean for bearings manufacturer determination of optimal cutting parameter with maximum possible use of tool lifetime. Standard ISO 3685 contains instructions how to create T-vc dependence for cutting tools made of cutting ceramic. In this standard are only instructions how to create T-vc dependence according to Taylor. The article compares T-vc dependencies for various cutting ceramics (Al2O3, Al2O3+ZrO2, Al2O3+TiCN) with T-vc dependence defined in standard ISO 3685, because this standard describes T-vc dependence for all entered cutting materials together.

The Analysis of Ceramic Cutting Tools Durability in Machining Process of Steel C60 Applied According to Standard ISO 3685

2013 ◽  
Vol 275-277 ◽  
pp. 2190-2194 ◽  
Author(s):  
Anton Panda ◽  
Ján Duplák ◽  
Jozef Jurko ◽  
Marcel Behún ◽  
Marek Jančík
Keyword(s):  
Cutting Tool ◽  
Cutting Tools ◽  
Machining Process ◽  
Technological Operation ◽  
Technical Science ◽  
Cutting Ceramic ◽  
Comprehensive Information ◽  
Tool Durability

Very important cutting tool property is its durability. Durability of cutting tool defines lifetime of this cutting tool and it determines its suitability for select technological operation. Technical science defines a lot of different factors, that they may be cause of shorter cutting tool lifetime. For increase cutting tool durability is necessary maximally possible elimination of these factors. Determination of cutting tool durability is very important, because provides comprehensive information how to determine appropriate technological conditions for selected cutting tool. In engineering is for determination of cutting tools durability used T-vc dependence. The article describes process how to create durability dependence for cutting tools made of cutting ceramic by means of T-vc dependence in machining process of C60.

The Comparison of Durability Ceramic Cutting Tools in Turning Process of Steel 80MoCrV4016

2014 ◽  
Vol 718 ◽  
pp. 110-115
Author(s):  
Michal Hatala ◽  
Ján Duplák ◽  
Marek Kočiško ◽  
Miroslav Kormoš ◽  
Miroslav Mičko ◽  
...  
Keyword(s):  
Main Part ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Machining Process ◽  
Engineering Practice ◽  
Technological Operation ◽  
Turning Process ◽  
Cutting Ceramic ◽  
Tool Durability ◽  
Inputs And Outputs

Every experiment has inputs and outputs. Inputs are defined before experiment and they are accurately determined and described. Outputs have to be measured and described after experiment. It is very difficult to describe and express parameters that are base of experiments. Tested parameters and theirs dependencies are very often described by means of graphs, tables or definitions. Lot of parameters and their dependencies in engineering practice are not described by means of formula. Very important and often used standard ISO in engineering practice is standard ISO 3685. This standard includes characteristics for various cutting materials. The main part of this standard is T-vc dependence for cutting materials. One of the cutting materials contained in standard ISO 3685 is cutting ceramic. There are instructions obtained in standard ISO 3685 for creation of T-vc dependence. Specification cutting tools durability made of cutting ceramic in machining process of steel 80MoCrV4016 is very important for economics of small and medium-sized enterprises, because cutting tool durability is factor that significantly affects the budget of these enterprises. This problematic is determined for small and medium-sized manufacturers of bearings, because steel 80MoCrV4016 is most commonly used for production of bearings. Durability of cutting tool defines lifetime of this cutting tool and it determines its suitability for select technological operation. The article describes process how to create durability dependence for cutting tools made of cutting ceramic by means of T-vc dependence in machining process of steel 80MoCrV4016.

Deformation Replication

1970 ◽  
Vol 28 ◽  
pp. 280-281
Author(s):  
J. Temple Black
Keyword(s):  
Cutting Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Rake Face ◽  
Orthogonal Machining ◽  
Aluminum Chips ◽  
Before And After ◽  
Materials Used ◽  
Glass Knife ◽  
Very High

Tool materials used in ultramicrotomy are glass, developed by Latta and Hartmann (1) and diamond, introduced by Fernandez-Moran (2). While diamonds produce more good sections per knife edge than glass, they are expensive; require careful mounting and handling; and are time consuming to clean before and after usage, purchase from vendors (3-6 months waiting time), and regrind. Glass offers an easily accessible, inexpensive material ($0.04 per knife) with very high compressive strength (3) that can be employed in microtomy of metals (4) as well as biological materials. When the orthogonal machining process is being studied, glass offers additional advantages. Sections of metal or plastic can be dried down on the rake face, coated with Au-Pd, and examined directly in the SEM with no additional handling (5). Figure 1 shows aluminum chips microtomed with a 75° glass knife at a cutting speed of 1 mm/sec with a depth of cut of 1000 Å lying on the rake face of the knife.

Performance Analysis on Eco-friendly Machining of Ti6Al4V using Powder Mixed with Different Dielectrics in WEDM

2020 ◽  
Vol 17 (3) ◽  
pp. 8128-8139
Author(s):  
S. Chakraborty ◽  
S. Mitra ◽  
D. Bose
Keyword(s):  
Metal Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Process Efficiency ◽  
Machining Parameters ◽  
Dielectric Fluids ◽  
High Emission ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process

The recent scenario of modern manufacturing is tremendously improved in the sense of precision machining and abstaining from environmental pollution and hazard issues. In the present work, Ti6Al4V is machined through wire EDM (WEDM) process with powder mixed dielectric and analyzed the influence of input parameters and inherent hazard issues. WEDM has different parameters such as peak current, pulse on time, pulse off time, gap voltage, wire speed, wire tension and so on, as well as dielectrics with powder mixed. These are playing an essential role in WEDM performances to improve the process efficiency by developing the surface texture, microhardness, and metal removal rate. Even though the parameter’s influencing, the study of environmental effect in the WEDM process is very essential during the machining process due to the high emission of toxic vapour by the high discharge energy. In the present study, three different dielectric fluids were used, including deionised water, kerosene, and surfactant added deionised water and analysed the data by taking one factor at a time (OFAT) approach. From this study, it is established that dielectric types and powder significantly improve performances with proper set of machining parameters and find out the risk factor associated with the PMWEDM process.

Modeling of Self-Induced Vibrations that Occur During the Machining Process of Casting Patterns with the Use of The Fuzzy-Neural Networks Method

2013 ◽  
Vol 58 (3) ◽  
pp. 871-875
Author(s):  
A. Herberg
Keyword(s):  
Neural Networks ◽  
Control System ◽  
Network Structure ◽  
Fuzzy Systems ◽  
Fuzzy Neural Networks ◽  
Cnc Machining ◽  
Machining Process ◽  
Modeling Process ◽  
Fuzzy Neural ◽  
Takagi Sugeno

Abstract This article outlines a methodology of modeling self-induced vibrations that occur in the course of machining of metal objects, i.e. when shaping casting patterns on CNC machining centers. The modeling process presented here is based on an algorithm that makes use of local model fuzzy-neural networks. The algorithm falls back on the advantages of fuzzy systems with Takagi-Sugeno-Kanga (TSK) consequences and neural networks with auxiliary modules that help optimize and shorten the time needed to identify the best possible network structure. The modeling of self-induced vibrations allows analyzing how the vibrations come into being. This in turn makes it possible to develop effective ways of eliminating these vibrations and, ultimately, designing a practical control system that would dispose of the vibrations altogether.

SURFACE IRREGULARITIES AS A COMPLEX SIGNAL OF TOOL REPRESENTATION TOGETHER WITH UNEVEN DISPLACEMENT IN RESPECT TO THE WORKPIECE

2014 ◽  
Vol 21 (1) ◽  
pp. 133-144 ◽  
Author(s):  
Adam Boryczko ◽  
Wojciech Rytlewski
Keyword(s):  
Machining Process ◽  
Surface Irregularity ◽  
Complex Signal ◽  
Complex Phenomenon ◽  
Tool Profile ◽  
Surface Irregularities ◽  
The Individual ◽  
Frequency Functions

Abstract In a dynamic machining process, distortion in surface irregularity is a very complex phenomenon. Surface irregularities form a periodic representation of the tool profile with various kinds of disturbance in a broad range of changes in the height and length of the profile. To discern these irregularity disturbances, interactions of the tool in the form of changes perpendicular and parallel relative to the workpiece were analyzed and simulated. The individual kinds of displacement of the tool relative to the workpiece introduce distortions in the changes of height and length. These changes are weakly represented in standard height and length irregularity parameters and their discernment has been found through amplitude-frequency functions.

Sign in / Sign up

Export Citation Format

Share Document