scholarly journals Radiative Flux of a Spectral Distribution at the Surface of a TPV Thermal Emitter Resulting from the Combustion of Biomass: Case of Palms Nut Shells

2021 ◽  
Vol 39 (4) ◽  
pp. 1351-1357
Author(s):  
Leonard Ribot Chuisseu Nguewo ◽  
Marcel Brice Obounou Akong ◽  
Clement Tchawoua ◽  
Prosper Gopdjim Noumo ◽  
Fabrice Mbakop Kwefeu ◽  
...  
Keyword(s):  
Heat Flux ◽  
Waste Heat ◽  
Wave Length ◽  
Electrical Energy ◽  
Biomass Combustion ◽  
Maximum Heat ◽  
Average Temperature ◽  
Cogeneration System ◽  
Thermal Emitter ◽  
Artificial Heat

Thermo PhotoVoltaic (TPV) system convert into electrical energy the radiation emitted from an artificial heat source (i.e., solar or combustion) by the use of photovoltaic cells. In the last decade, TPV system has gained an increasing attention as cogeneration system for the distributed generation sector. Nevertheless, these systems are not fully developed and studied: several aspects need to be further investigated and completely understood. In this study, we modeled and investigated by performing numerical simulation on the feasibility of the TPV system exploiting waste heat energy during biomass combustion. To achieve this goal, we considered a TPV system in which we evaluated and analyzed the waste heat flux resulting from the combustion of the palm nuts shells as well as the corresponding temperature received at the surface of the TPV Thermal-emitter. Furthermore, we evaluated the heat intensity. Results obtained shows that the average temperature at the TPV absorber-emitter is around 1600k. Different variation of the net heat flux at the TPV absorber-emitter are observed for different position. The maximum heat intensity is around 15*1010 W.m-2.µm-1 for a wave length of 2000 nm. These results indicate that the model presented herein is therefore suitable for the design of the TPV system.

Laboratory Control and Measurement System of a Dual-Fuel Compression Ignition Combustion Engine Operating in a Cogeneration System

2013 ◽  
Vol 210 ◽  
pp. 200-205 ◽  
Author(s):  
Sławomir Wierzbicki
Keyword(s):  
Waste Heat ◽  
Combustion Engine ◽  
Renewable Energy Sources ◽  
Electrical Energy ◽  
Dual Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Laboratory Control ◽  
Cogeneration System ◽  
Electrical Energy Production

Electrical energy production from renewable energy sources is currently one of the key directions of conducted research. This paper describes a developed laboratory control system for the operation of a dual-fuel compression ignition engine in which the main fuel charge is fed in the form of biogas with variable composition, it also describes a system enabling the measurement of waste heat from this engine.

Effect of Electron-Phonon Coupling on Transport Properties of Monolayers of ZrS2, BiI3 and PbI2: A thermoelectric Perspective

2021 ◽  
Author(s):  
Gautam Sharma ◽  
Vineet Kumar Pandey ◽  
Shouvik Datta ◽  
Prasenjit Ghosh
Keyword(s):  
Relaxation Time ◽  
Band Structure ◽  
Transport Properties ◽  
Thermoelectric Properties ◽  
Thermoelectric Materials ◽  
Waste Heat ◽  
Transport Coefficients ◽  
Electrical Energy ◽  
Phonon Coupling ◽  
Electron Phonon Coupling

Thermoelectric materials are used for conversion of waste heat to electrical energy. The transport coefficients that determine their thermoelectric properties depend on the band structure and the relaxation time of...

scholarly journals Thermoelectric Properties of Carbon Nanotubes

Energies ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 4561 ◽  
Author(s):  
Nguyen T. Hung ◽  
Ahmad R. T. Nugraha ◽  
Riichiro Saito
Keyword(s):  
Carbon Nanotubes ◽  
Figure Of Merit ◽  
Waste Heat ◽  
Quantum Confinement Effect ◽  
Electrical Energy ◽  
High Seebeck Coefficient ◽  
Te Material ◽  
P Type ◽  
State Device ◽  
Solid State Device

Thermoelectric (TE) material is a class of materials that can convert heat to electrical energy directly in a solid-state-device without any moving parts and that is environmentally friendly. The study and development of TE materials have grown quickly in the past decade. However, their development goes slowly by the lack of cheap TE materials with high Seebeck coefficient and good electrical conductivity. Carbon nanotubes (CNTs) are particularly attractive as TE materials because of at least three reasons: (1) CNTs possess various band gaps depending on their structure, (2) CNTs represent unique one-dimensional carbon materials which naturally satisfies the conditions of quantum confinement effect to enhance the TE efficiency and (3) CNTs provide us with a platform for developing lightweight and flexible TE devices due to their mechanical properties. The TE power factor is reported to reach 700–1000 W / m K 2 for both p-type and n-type CNTs when purified to contain only doped semiconducting CNT species. Therefore, CNTs are promising for a variety of TE applications in which the heat source is unlimited, such as waste heat or solar heat although their figure of merit Z T is still modest (0.05 at 300 K). In this paper, we review in detail from the basic concept of TE field to the fundamental TE properties of CNTs, as well as their applications. Furthermore, the strategies are discussed to improve the TE properties of CNTs. Finally, we give our perspectives on the tremendous potential of CNTs-based TE materials and composites.

scholarly journals Pool Boiling of Nanofluids on Biphilic Surfaces: An Experimental and Numerical Study

Nanomaterials ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 125
Author(s):  
Eduardo Freitas ◽  
Pedro Pontes ◽  
Ricardo Cautela ◽  
Vaibhav Bahadur ◽  
João Miranda ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Numerical Model ◽  
Heat Dissipation ◽  
Numerical Study ◽  
Pool Boiling ◽  
Temperature Drop ◽  
Surface Cooling ◽  
Average Temperature ◽  
Gold Silver

This study addresses the combination of customized surface modification with the use of nanofluids, to infer on its potential to enhance pool-boiling heat transfer. Hydrophilic surfaces patterned with superhydrophobic regions were developed and used as surface interfaces with different nanofluids (water with gold, silver, aluminum and alumina nanoparticles), in order to evaluate the effect of the nature and concentration of the nanoparticles in bubble dynamics and consequently in heat transfer processes. The main qualitative and quantitative analysis was based on extensive post-processing of synchronized high-speed and thermographic images. To study the nucleation of a single bubble in pool boiling condition, a numerical model was also implemented. The results show an evident benefit of using biphilic patterns with well-established distances between the superhydrophobic regions. This can be observed in the resulting plot of the dissipated heat flux for a biphilic pattern with seven superhydrophobic spots, δ = 1/d and an imposed heat flux of 2132 w/m2. In this case, the dissipated heat flux is almost constant (except in the instant t* ≈ 0.9 when it reaches a peak of 2400 W/m2), whilst when using only a single superhydrophobic spot, where the heat flux dissipation reaches the maximum shortly after the detachment of the bubble, dropping continuously until a new necking phase starts. The biphilic patterns also allow a controlled bubble coalescence, which promotes fluid convection at the hydrophilic spacing between the superhydrophobic regions, which clearly contributes to cool down the surface. This effect is noticeable in the case of employing the Ag 1 wt% nanofluid, with an imposed heat flux of 2132 W/m2, where the coalescence of the drops promotes a surface cooling, identified by a temperature drop of 0.7 °C in the hydrophilic areas. Those areas have an average temperature of 101.8 °C, whilst the average temperature of the superhydrophobic spots at coalescence time is of 102.9 °C. For low concentrations as the ones used in this work, the effect of the nanofluids was observed to play a minor role. This can be observed on the slight discrepancy of the heat dissipation decay that occurred in the necking stage of the bubbles for nanofluids with the same kind of nanoparticles and different concentration. For the Au 0.1 wt% nanofluid, a heat dissipation decay of 350 W/m2 was reported, whilst for the Au 0.5 wt% nanofluid, the same decay was only of 280 W/m2. The results of the numerical model concerning velocity fields indicated a sudden acceleration at the bubble detachment, as can be qualitatively analyzed in the thermographic images obtained in this work. Additionally, the temperature fields of the analyzed region present the same tendency as the experimental results.

Experimental Research of Energy Harvesting and Storage Based on Ferroelectric Materials

2012 ◽  
Vol 476-478 ◽  
pp. 1336-1340
Author(s):  
Kai Feng Li ◽  
Rong Liu ◽  
Lin Xiang Wang
Keyword(s):  
Energy Harvesting ◽  
Electromagnetic Waves ◽  
Vibrational Energy ◽  
Waste Heat ◽  
Mechanical Strain ◽  
Electrical Potential ◽  
Electrical Energy ◽  
Ferroelectric Materials ◽  
Energy Scavenging ◽  
And Storage

The concept of energy harvesting works towards developing self-powered devices that do not require replaceable power supplies. Energy scavenging devices are designed to capture the ambient energy surrounding the electronics and convert it into usable electrical energy. A number of sources of harvestable ambient energy exist, including waste heat, vibration, electromagnetic waves, wind, flowing water, and solar energy. While each of these sources of energy can be effectively used to power remote sensors, the structural and biological communities have placed an emphasis on scavenging vibrational energy with ferroelectric materials. Ferroelectric materials have a crystalline structure that provide a unique ability to convert an applied electrical potential into a mechanical strain or vice versa. Based on the properties of the material, this paper investigates the technique of power harvesting and storage.

Analysis of Surface Waste Heat Recovery in IC Engine by Using TEG

2015 ◽  
Vol 787 ◽  
pp. 782-786 ◽  
Author(s):  
R. Prakash ◽  
D. Christopher ◽  
K. Kumarrathinam
Keyword(s):  
Waste Heat ◽  
Electrical Power ◽  
Electrical Energy ◽  
Surface Heat ◽  
Heat Energy ◽  
Ic Engine ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Power Point ◽  
Heat Energy Recovery

The prime objective of this paper is to present the details of a thermoelectric waste heat energy recovery system for automobiles, more specifically, the surface heat available in the silencer. The key is to directly convert the surface heat energy from automotive waste heat to electrical energy using a thermoelectric generator, which is then regulated by a DC–DC Cuk converter to charge a battery using maximum power point tracking. Hence, the electrical power stored in the battery can be maximized. Also the other face of the TEG will remain cold. Hence the skin burn out accidents can be avoided. The experimental results demonstrate that the proposed system can work well under different working conditions, and is promising for automotive industry.

Boiling Heat Transfer Characteristics of Rotary Hollow Cylinders with In-Line and Staggered Multiple Arrays of Water Jets

2021 ◽  
Author(s):  
Mohammad Jahedi ◽  
Bahram Moshfegh
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Stagnation Point ◽  
Surface Heat Flux ◽  
Surface Heat ◽  
Maximum Heat ◽  
Water Jets ◽  
Maximum Heat Flux ◽  
Inner Surface ◽  
Hollow Cylinders

Abstract Transient heat transfer studies of quenching rotary hollow cylinders with in-line and staggered multiple arrays of jets have been carried out experimentally. The study involves three hollow cylinders (Do/d = 12 to 24) with rotation speed 10 to 50 rpm, quenched by subcooled water jets (ΔTsub=50-80 K) with jet flow rate 2.7 to 10.9 L/min. The increase in area-averaged and maximum heat flux over quenching surface (Af) has been observed in the studied multiple arrays with constant Qtotal compared to previous studies. Investigation of radial temperature distribution at stagnation point of jet reveals that the footprint of configuration of 4-row array is highlighted in radial distances near the outer surface and vanishes further down toward the inner surface. The influence of the main quenching parameters on local average surface heat flux at stagnation point is addressed in all the boiling regimes where the result indicates jet flow rate provides strongest effect in all the boiling regimes. Effectiveness of magnitude of maximum heat flux in the boiling curve for the studied parameters is reported. The result of spatial and temporal heat flux by radial conduction in the solid presents projection depth of cyclic variation of surface heat flux in the radial axis as it disappears near inner surface of hollow cylinder. In addition, correlations are proposed for area-averaged Nusselt number as well as average and maximum local heat flux at stagnation point of jet for the in-line and staggered multiple arrays.

Optimization of a radiant system for hydrothermal performance using Taguchi and utility concept

2021 ◽  
pp. 1-29
Author(s):  
Ratnadeep Nath ◽  
Vikas Verma ◽  
Rahul Tarodiya
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Temperature Difference ◽  
Wall Temperature ◽  
Thermal Parameters ◽  
Conventional Heating ◽  
Geometrical Parameters ◽  
Maximum Heat ◽  
Utility Concept ◽  
Heating Mode

Abstract Radiant floor panel technology is gaining popularity as an alternative system over conventional heating, ventilation and, air conditioning system (HVAC) to maintain the room temperature for the desired comfort. This research paper aims to optimize the hydrothermal performance of a radiant system by implementing the Taguchi technique and utility concept for cooling and heating mode of operation. Five geometrical and thermal parameters such as pipe diameter, pipe spacing, concrete layer thickness, wall temperature, and inlet and outlet water temperature difference with three levels are chosen as controlling factors to perform optimization. Considering five parameters and three levels, a total of 27 trial runs (L27) are constructed and computed by mathematical calculation. Two different sets of optimum parameters are obtained for maximizing heat flux and minimizing pressure drop. Further, the utility concept is employed to get a single set of parameters to achieve maximum utilization of the radiant system. Taguchi analysis revealed that thermal parameters like temperature difference and wall temperature are the most influential parameters to reach maximum heat transfer and minimum pressure drop followed by geometrical parameters like pipe spacing and diameter for heat flux and pressure drop, respectively. Providing more weightage to heat flux than pressure drop, utility analysis showed 32% and 42% augmentation in heat flux for cooling and heating mode respectively, at the cost of an increase in pressure drop.

Sign in / Sign up

Export Citation Format

Share Document