Laboratory Investigation of Impact of Slickwater Composition on Multiphase Permeability Evolution in Tight Sandstones

2021 ◽  
pp. 1-15
Author(s):  
Kelvin Abaa ◽  
John Wang ◽  
Derek Elsworth ◽  
Mku Ityokumbul

Summary Fracturing fluid filtrate that leaks off during injection is imbibed by strong capillary forces present in low-permeability sandstones and may severely reduce the effective gas permeability during cleanup and post-fracture production. This work aims to investigate the role fracturing fluid filtrate from slickwater has on rock-fluid and fluid-fluid interactions and to quantify the resulting multiphase permeability evolution during imbibition and drainage of the filtrate by means of specialized core laboratory techniques. Three suites of experiments were conducted. In the first suite of experiments, a fluid leakoff test was conducted on selected core samples to determine the extent of polymer invasion and leakoff characteristics. In the second suite, multigas relative permeability measurements were conducted on sandstone plugs saturated with fracturing fluid filtrate. A combination of controlled fluid evaporation and pulse decay permeability technique was used to measure liquid and gas effective permeabilities for both drainage and imbibition cycles. These experiments aim to capture dynamic permeability evolution during invasion and cleanup of fracturing fluid (slickwater). The final suite of experiments consists of adsorption flow tests to investigate, identify, and quantify possible mechanisms for adsorption of the polymeric molecules of friction reducers present in the fluid filtrate to the pore walls of the rock sample. Imbibition tests and observations of contact angles were conducted to validate possible wettability changes. Results from multiphase permeability flow tests show an irreversible reduction in endpoint brine permeability and relative permeability with increasing concentration of friction reducer. Our results also show that effective gas permeability during drainage/cleanup of the imbibed slickwater fluid is controlled to a large degree by trapped gas saturation than by changes in interfacial tension. Adsorption flow tests identified adsorption of polymeric molecules of the friction reducer present in the fluid to the pore walls of the rock. The adsorption friction reducer increases the wettability of the rock surface and results in the reduction of liquid relative permeability. The originality of this work is to diagnose formation damage mechanisms from laboratory experiments that adequately capture multiphase permeability evolution specific to a slickwater fluid system, during imbibition and cleanup. This will be useful in optimizing fracturing fluid selection.

SPE Journal ◽  
2017 ◽  
Vol 22 (06) ◽  
pp. 1915-1928 ◽  
Author(s):  
Saeid Khorsandi ◽  
Liwei Li ◽  
Russell T. Johns

Summary Commercial compositional simulators commonly apply correlations or empirical relations that are based on fitting experimental data to calculate phase relative permeabilities. These relations cannot adequately capture the effects of hysteresis, fluid compositional variations, and rock-wettability alteration. Furthermore, these relations require phases to be labeled, which is not accurate for complex miscible or near-miscible displacements with multiple hydrocarbon phases. Therefore, these relations can be discontinuous for compositional processes, causing inaccuracies and numerical problems in simulation. This paper develops for the first time an equation-of-state (EOS) to model robustly and continuously the relative permeability as a function of phase saturations and distributions, fluid compositions, rock-surface properties, and rock structure. Phases are not labeled; instead, the phases in each gridblock are ordered on the basis of their compositional similarity. Phase compositions and rock-surface properties are used to calculate wettability and contact angles. The model is tuned to measured two-phase relative permeability curves with very few tuning parameters and then is used to predict relative permeability away from the measured experimental data. The model is applicable to all flow in porous-media processes, but is especially important for low-salinity polymer, surfactant, miscible gas, and water-alternating-gas (WAG) flooding. The results show excellent ability to match measured data, and to predict observed trends in hysteresis and oil-saturation trapping, including those from Land's model and for a wide range in wettability. The results also show that relative permeabilities are continuous at critical points and yield a physically correct numerical solution when incorporated within a compositional simulator (PennSim 2013). The model has very few tuning parameters, and the parameters are directly related to physical properties of rock and fluid, which can be measured. The new model also offers the potential for incorporating results from computed-tomography (CT) scans and pore-network models to determine some input parameters for the new EOS.


Water ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1653
Author(s):  
Guofu Li ◽  
Yi Wang ◽  
Junhui Wang ◽  
Hongwei Zhang ◽  
Wenbin Shen ◽  
...  

Deep coalbed methane (CBM) is widely distributed in China and is mainly commercially exploited in the Qinshui basin. The in situ stress and moisture content are key factors affecting the permeability of CH4-containing coal samples. Therefore, considering the coupled effects of compressing and infiltrating on the gas permeability of coal could be more accurate to reveal the CH4 gas seepage characteristics in CBM reservoirs. In this study, coal samples sourced from Tunlan coalmine were employed to conduct the triaxial loading and gas seepage tests. Several findings were concluded: (1) In this triaxial test, the effect of confining stress on the permeability of gas-containing coal samples is greater than that of axial stress. (2) The permeability versus gas pressure curve of coal presents a ‘V’ shape evolution trend, in which the minimum gas permeability was obtained at a gas pressure of 1.1MPa. (3) The gas permeability of coal samples decreased exponentially with increasing moisture content. Specifically, as the moisture content increasing from 0.18% to 3.15%, the gas permeability decreased by about 70%. These results are expected to provide a foundation for the efficient exploitation of CBM in Qinshui basin.


2022 ◽  
Vol 29 (1) ◽  
pp. 12
Author(s):  
Yin Zeng ◽  
Lu Wang ◽  
Chaofu Deng ◽  
Qiangxing Zhang ◽  
Zhide Wu ◽  
...  

2021 ◽  
Author(s):  
Xurong Zhao ◽  
Tianbo Liang ◽  
Jingge Zan ◽  
Mengchuan Zhang ◽  
Fujian Zhou ◽  
...  

Abstract Replacing oil from small pores of tight oil-wet rocks relies on altering the rock wettability with the injected fracturing fluid. Among different types of wettability-alteration surfactants, the liquid nanofluid has less adsorption loss during transport in the porous media, and can efficiently alter the rock wettability; meanwhile, it can also maintain a certain oil-water interfacial tension driving the water imbibition. In the previous study, the main properties of a Nonionic nanofluid-diluted microemulsion (DME) were evaluated, and the dispersion coefficient and adsorption rate of DME in tight rock under different conditions were quantified. In this study, to more intuitively show the change of wettability of DME to oil-wet rocks in the process of core flooding experiments and the changes of the water invasion front, CT is used to carry out on-line core flooding experiments, scan and calculate the water saturation in time, and compare it with the pressure drop in this process. Besides, the heterogeneity of rock samples is quantified in this paper. The results show that when the DME is used as the fracturing fluid additive, fingering of the water phase is observed at the beginning of the invasion; compared with brine, the fracturing fluid with DME has deeper invasion depth at the same time; the water invasion front gradually becomes uniform when the DME alters the rock wettability and triggers the imbibition; for tight rocks, DME can enter deeper pores and replace more oil because of its dominance. Finally, the selected nanofluids of DME were tested in two horizontal wells in the field, and their flowback fluids were collected and analyzed. The results show that the average droplet size of the flowback fluids in the wells using DME decreases with production time, and the altered wetting ability gradually returns to the level of the injected fracturing fluid. It can be confirmed that DME can migrate within the tight rock, make the rock surface more water-wet and enhance the imbibition capacity of the fracturing fluid, to reduce the reservoir pressure decline rate and increase production.


2020 ◽  
Vol 146 ◽  
pp. 03003
Author(s):  
M. Ben Clennell ◽  
Cameron White ◽  
Ausama Giwelli ◽  
Matt Myers ◽  
Lionel Esteban ◽  
...  

Standard test methods for measuring imbibition gas-brine relative permeability on reservoir core samples often lead to non-uniform brine saturation. During co-current flow, the brine tends to bank up at the sample inlet and redistributes slowly, even with fractional flow of gas to brine of 400:1 or more. The first reliable Rel Perm point is often only attained after a brine saturation of around Sw=40% is achieved, leaving a data gap between Swirr and this point. The consequent poor definition of the shape of the Rel Perm function can lead to uncertainty in the performance of gas reservoirs undergoing depletion drive with an encroaching aquifer or subjected to a water flood. We have developed new procedures to pre-condition brine saturation outside of the test rig and progress it in small increments to fill in the data gap at low Sw, before continuing with a co-current flood to the gas permeability end-point. The method was applied to series of sandstone samples from gas reservoirs from the NW Shelf of Australia, and a Berea standard. We found that the complete imbibition relative permeability curve is typically ‘S’ shaped or has a rolling over, convex-up shape that is markedly different from the concave-up, Corey Rel Perm curve usually fitted to SCAL test data. This finding may have an economic upside if the reservoir produces gas at a high rate for longer than was originally predicted based on the old Rel Perm curves.


Molecules ◽  
2020 ◽  
Vol 25 (13) ◽  
pp. 3030
Author(s):  
Amjed Hassan ◽  
Mohamed Mahmoud ◽  
Muhammad Shahzad Kamal ◽  
Syed Muhammad Shakil Hussain ◽  
Shirish Patil

Condensate accumulation in the vicinity of the gas well is known to curtail hydrocarbon production by up to 80%. Numerous approaches are being employed to mitigate condensate damage and improve gas productivity. Chemical treatment, gas recycling, and hydraulic fracturing are the most effective techniques for combatting the condensate bank. However, the gas injection technique showed temporary condensate recovery and limited improvement in gas productivity. Hydraulic fracturing is considered to be an expensive approach for treating condensate banking problems. In this study, a newly synthesized gemini surfactant (GS) was developed to prevent the formation of condensate blockage in the gas condensate reservoirs. Flushing the near-wellbore area with GS will change the rock wettability and thereby reduce the capillary forces holding the condensate due to the strong adsorption capacity of GS on the rock surface. In this study, several measurements were conducted to assess the performance of GS in mitigating the condensate bank including coreflood, relative permeability, phase behavior, and nuclear magnetic resonance (NMR) measurements. The results show that GS can reduce the capillary pressure by as much as 40%, increase the condensate mobility by more than 80%, and thereby mitigate the condensate bank by up to 84%. Phase behavior measurements indicate that adding GS to the oil–brine system could not induce any emulsions at different salinity levels. Moreover, NMR and permeability measurements reveal that the gemini surfactant has no effect on the pore system and no changes were observed in the T2 relaxation profiles with and without the GS injection. Ultimately, this work introduces a novel and effective treatment for mitigating the condensate bank. The new treatment showed an attractive performance in reducing liquid saturation and increasing the condensate relative permeability.


SPE Journal ◽  
2019 ◽  
Vol 24 (03) ◽  
pp. 1092-1107 ◽  
Author(s):  
M.. Tagavifar ◽  
M.. Balhoff ◽  
K.. Mohanty ◽  
G. A. Pope

Summary Surfactants induce spontaneous imbibition of water into oil-wet porous media by wettability alteration and interfacial-tension (IFT) reduction. Although the dependence of imbibition on wettability alteration is well-understood, the role of IFT is not as clear. This is partly because, at low IFT values, most water/oil/amphiphile(s) mixtures form emulsions and/or microemulsions, suggesting that the imbibition is accompanied by a phase change, which has been neglected or incorrectly accounted for in previous studies. In this paper, spontaneous displacement of oil from oil-wet porous media by microemulsion-forming surfactants is investigated through simulations and the results are compared with existing experimental data for low-permeability cores with different aspect ratios and permeabilities. Microemulsion viscosity and oil contact angles, with and without surfactant, were measured to better initialize and constrain the simulation model. Results show that with such processes, the imbibition rate and the oil recovery scale differently with core dimensions. Specifically, the rate of imbibition is faster in cores with larger diameter and height, but the recovery factor is smaller when the core aspect ratio deviates considerably from unity. With regard to the mechanism of water uptake, our results suggest, for the first time, that (i) microemulsion formation (i.e., fluid/fluid interface phenomenon) is fast and favored over the wettability alteration (i.e., rock-surface phenomenon) in short times; (ii) a complete wettability transition from an oil-wet to a mixed microemulsion-wet and surfactant-wet state always occurs at ultralow IFT; (iii) wettability alteration causes a more uniform imbibition profile along the core but creates a more diffused imbibition front; and (iv) total emulsification is a strong assumption and fails to describe the dynamics and the scaling of imbibition. Wettability alteration affects the imbibition dynamics locally by changing the composition path, and at a distance by changing the flow behavior. Simulations predict that even though water is not initially present, it forms inside the core. The implications of these results for optimizing the design of low-IFT imbibition are discussed.


2013 ◽  
Vol 65 (07) ◽  
pp. 28-30
Author(s):  
Geeta Nakra ◽  
Steven Wright ◽  
David Wright

Sign in / Sign up

Export Citation Format

Share Document