scholarly journals Modeling and Analysis of Diagnostic Fracture Injection Tests DFITs

2021 ◽  
Author(s):  
Recep Bakar ◽  
Erdal Ozkan ◽  
Hossein Kazemi
Keyword(s):  
Effective Permeability ◽  
Function Analysis ◽  
Fracture Network ◽  
Unconventional Reservoirs ◽  
Fracture Aperture ◽  
Modeling And Analysis ◽  
Matrix Permeability ◽  
Straight Line ◽  
Order Of Magnitude ◽  
The Impact

Abstract Diagnostic fracture injection tests (DFIT) are used as an indirect method to determine closure pressure and formation effective permeability in unconventional reservoirs as a first step in formation evaluation. The information obtained from DFIT is particularly useful because it is obtained before any production for a given well is available. In DFIT, a small fracture is created by injecting few barrels of completion fluid until formation breaks down and a fracture is initiated and propagates a short distance into the reservoir. Then, injection is stopped, and the pressure decline (or falloff) is monitored. From this pressure decline, the effective permeability of the formation is estimated by Nolte's G-function, log-log plot, or square root of time analysis. In this research, the viability of the common DFIT analysis techniques was investigated for unconventional reservoirs with and without micro-fractures by using a numerical hydraulic fracturing simulator, CFRAC. The results of numerical simulations were investigated to assess the impact of permeability, residual fracture aperture, and complex fracture networks on conventional DFIT interpretations. For the example considered in this work, the commonly used G-function analysis yielded estimates of permeability over an order of magnitude higher than the simulated matrix permeability. Error in the G-function estimates of permeability were higher for higher matrix permeability and in the existence of a fracture network. On the other hand, straight-line analysis of Ap versus G-time yielded much closer (in the same order of magnitude) estimates of permeability.

Numerical Simulation of the Impact of Natural Fracture on Fluid Composition Variation Through a Porous Medium

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Ali Papi ◽  
Ali Mohebbi ◽  
S. Ehsan Eshraghi
Keyword(s):  
Fracture Network ◽  
Natural Fracture ◽  
Computational Time ◽  
Single Fracture ◽  
Fracture Aperture ◽  
Fluid Composition ◽  
Composition Distribution ◽  
Engineering Software ◽  
Composition Variation ◽  
The Impact

In order to lessen the computational time in fractured oil reservoir simulations, all fractures are usually assumed to be as one equivalent fracture at the center or around the model. This, specially, has applications in industrial engineering software, where this assumption applies. In this study, using two general contradictory examples, it is shown that ignoring a fracture network and assuming an equivalent single-fracture has no logical justification and results in a considerable error. The effect of fracture aperture on composition distribution of a binary and a ternary mixture was also investigated. These mixtures were C1 (methane)/n-C4 (normal-butane) and C1 (methane)/C2 (ethane)/n-C4 (normal-butane), which were under diffusion and natural convection. Governing equations were numerically solved using matlab. One of the main relevant applications of this study is where permeability and temperature gradient are the key difference between reservoirs. Compositional distribution from this study could be used to estimate initial oil in place. Using this study, one can find the optimum permeability, namely the permeability at which the maximum species separation happens, and the threshold permeability (or fracture aperture), after which the convection imposes its effect on composition distribution. It is found that the threshold permeability is not constant from reservoir to reservoir. Also, one can find that full mixing happens in the model, namely heavy and light densities of top and bottom mix up together in the model. Furthermore, after maximum separation point, convection causes unification of components.

Pound Wise and Penny Foolish? Weight Loss and The Dynamics of Health Care Spending

2011 ◽  
Vol 14 (2) ◽  
Author(s):  
Thomas G Koch
Keyword(s):  
Weight Loss ◽  
Cost Savings ◽  
Cost Effective ◽  
Economic Consequences ◽  
Health Care Spending ◽  
Order Of Magnitude ◽  
Dynamic Measures ◽  
The Cost ◽  
The Impact ◽  
The Relationship

Current estimates of obesity costs ignore the impact of future weight loss and gain, and may either over or underestimate economic consequences of weight loss. In light of this, I construct static and dynamic measures of medical costs associated with body mass index (BMI), to be balanced against the cost of one-time interventions. This study finds that ignoring the implications of weight loss and gain over time overstates the medical-cost savings of such interventions by an order of magnitude. When the relationship between spending and age is allowed to vary, weight-loss attempts appear to be cost-effective starting and ending with middle age. Some interventions recently proven to decrease weight may also be cost-effective.

scholarly journals Ice Coverage Induced by Depositing a Water Drop onto the Supercooled Substrate at Extreme Low Vapor Pressure

Crystals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 691
Author(s):  
Yugang Zhao ◽  
Zichao Zuo ◽  
Haibo Tang ◽  
Xin Zhang
Keyword(s):  
Vapor Pressure ◽  
Substrate Temperature ◽  
Water Drop ◽  
Industrial Processes ◽  
Aircraft Icing ◽  
Ice Coverage ◽  
Fundamental Understanding ◽  
Order Of Magnitude ◽  
The Impact ◽  
Kinetics Of

Icing/snowing/frosting is ubiquitous in nature and industrial processes, and the accretion of ice mostly leads to catastrophic consequences. The existing understanding of icing is still limited, particularly for aircraft icing, where direct observation of the freezing dynamics is inaccessible. In this work, we investigate experimentally the impact and freezing of a water drop onto the supercooled substrate at extremely low vapor pressure, to mimic an aircraft passing through clouds at a relatively high altitude, engendering icing upon collisions with pendant drops. Special attention is focused on the ice coverage induced by an impinging drop, from the perimeter pointing outward along the radial direction. We observed two freezing regimes: (I) spread-recoil-freeze at the substrate temperature of Ts = −15.4 ± 0.2 °C and (II) spread (incomplete)-freeze at the substrate temperature of Ts = −22.1 ± 0.2 °C. The ice coverage is approximately one order of magnitude larger than the frozen drop itself, and counterintuitively, larger supercooling yields smaller ice coverage in the range of interest. We attribute the variation of ice coverage to the kinetics of vapor diffusion in the two regimes. This fundamental understanding benefits the design of new anti-icing technologies for aircraft.

scholarly journals Individual Condensation Trails in Aircraft Trajectory Optimization

2019 ◽  
Vol 11 (21) ◽  
pp. 6082 ◽  
Author(s):  
Judith Rosenow ◽  
Hartmut Fricke
Keyword(s):  
Global Warming ◽  
Trajectory Optimization ◽  
Wind Shear ◽  
Impact Factors ◽  
Factors Influencing ◽  
Order Of Magnitude ◽  
Aircraft Trajectory ◽  
The Impact ◽  
Arbitrary Trajectory ◽  
Significant Factors

Contrails are one of the driving contributors to global warming, induced by aviation. The quantification of the impact of contrails on global warming is nontrivial and requires further in-depth investigation. In detail, condensation trails might even change the algebraic sign between a cooling and a warming effect in an order of magnitude, which is comparable to the impact of aviation-emitted carbon dioxides and nitrogen oxides. This implies the necessity to granularly consider the environmental impact of condensation trails in single-trajectory optimization tools. The intent of this study is the elaboration of all significant factors influencing on the net effect of single condensation trails. Possible simplifications will be proposed for a consideration in single-trajectory optimization tools. Finally, the effects of the most important impact factors, such as latitude, time of the year, and time of the day, wind shear, and atmospheric turbulence as well as their consideration in a multi-criteria trajectory optimization tool are exemplified. The results can be used for an arbitrary trajectory optimization tool with environmental optimization intents.

Dual-Permeability Modeling of Capillary Diversion and Drift Shadow Effects in Unsaturated Fractured Rock

2009 ◽  
Vol 131 (10) ◽  
Author(s):  
Clifford K. Ho ◽  
Bill W. Arnold ◽  
Susan J. Altman
Keyword(s):  
Fractured Rock ◽  
Constitutive Relations ◽  
Water Flux ◽  
Fracture Network ◽  
Small Scale ◽  
Grid Refinement ◽  
Capillary Pressures ◽  
And Behavior ◽  
Capillary Pressure Curves ◽  
The Impact

The drift-shadow effect describes capillary diversion of water flow around a drift or cavity in porous or fractured rock, resulting in lower water flux directly beneath the cavity. This paper presents computational simulations of drift-shadow experiments using dual-permeability models, similar to the models used for performance assessment analyses of flow and seepage in unsaturated fractured tuff at Yucca Mountain. Comparisons were made between the simulations and experimental data from small-scale drift-shadow tests. Results showed that the dual-permeability models captured the salient trends and behavior observed in the experiments, but constitutive relations (e.g., fracture capillary-pressure curves) can significantly affect the simulated results. Lower water flux beneath the drift was observed in both the simulations and tests, and fingerlike flow patterns were seen to exist with lower simulated capillary pressures. The dual-permeability models used in this analysis were capable of simulating these processes. However, features such as irregularities along the top of the drift (e.g., from roof collapse) and heterogeneities in the fracture network may reduce the impact of capillary diversion and drift shadow. An evaluation of different meshes showed that at the grid refinement used, a comparison between orthogonal and unstructured meshes did not result in large differences.

A modified production function analysis of changing southern forest productivity

1991 ◽  
Vol 21 (8) ◽  
pp. 1278-1287 ◽  
Author(s):  
David H. Newman
Keyword(s):  
Production Function ◽  
Function Analysis ◽  
Public Lands ◽  
Forest Productivity ◽  
Southern States ◽  
The Past ◽  
Lower Productivity ◽  
Aggregate Production Function ◽  
The Impact ◽  
Productivity Gains

The analysis in this paper measures changes in forest productivity for 12 southern states using a modified, aggregate production function. The function combines cross section – time series, biological, and acreage data to estimate the shift in productivity, measured as either standing inventory plus removals or changes in inventory plus removals, over the past 4 decades. The annual shift in productivity is estimated to be approximately 0.5% for the standing volume measures used. However, productivity gains in the region have virtually stopped during the past decade. The largest contributions to productivity gains were from industrially owned lands and land managed as planted pine. Mixed pine–hardwood stands and public lands (except for plantations) showed lower productivity impacts. These results present an essential component for understanding the impact of technical change on aggregate forest productivity in the southern United States.

Discussion of Oxygen Threshold Level for Corrosion Management in Seawater Injection Systems

2021 ◽  
Author(s):  
Jean Vicente Ferrari
Keyword(s):  
Corrosion Rate ◽  
Oxygen Reduction ◽  
Water Injection ◽  
Steel Corrosion ◽  
Threshold Level ◽  
International Standards ◽  
Limiting Current ◽  
Order Of Magnitude ◽  
The Impact ◽  
Oxygen Concentrations

Abstract Generally, in water injection systems, oxygen levels starting from around eight ppm are deoxygenated to below 50 ppm, following international standards' guidelines. This work aims to discuss the impact of such a magnitude value of oxygen contamination on steel corrosion in seawater injection systems by analysing theoretical polarisation curves and results from published works with different approaches. Corrosion models consider mass-transfer controlled diffusion of oxygen to predict the maximum steel corrosion rate, which depends on the oxygen limiting current, which in turn is strongly influenced by flow velocity. The effect of free chlorine on corrosion in seawater injection systems has also been considered and included in an oxygen equivalent parameter. In such systems, where oxygen reduction is the key cathodic reaction, the corrosion process may be under cathodic activation control, independent of flow at higher velocities or when erosion-corrosion begins. In this work, theoretical polarisation curves were constructed by using published oxygen and chlorine cathodic limiting currents (iLc) on carbon steel and a noble metal electrode, respectively. Aerated (200 ppb and 9000 ppb of oxygen) and deaerated conditions (50 ppb of oxygen) and the presence of 300 ppb of chlorine were applied to the assumed exchange current densities (io). Neutral (pH 7) and acid (pH 4) conditions (considering the presence of CO2) were also assumed to be at room temperature and pressure. Since the corrosion rate in lower oxygen concentrations (ppb order of magnitude) may result in corrosion rates of the same order of magnitude than in higher oxygen concentrations (ppm order of magnitude) when comparing and analysing results from experimental, semi-empirical or mechanistic approaches, it is necessary to weigh up the effects of both steel surface (bare or scaled/corrosion products) and flow. At oxygen concentrations below 200 ppb and under acid conditions, the contribution of H+ reduction on corrosion rate starts to be higher than oxygen reduction, mainly in the absence of chlorine.

Local Mesh Refinement for Correlation of FEA Estimated Plastic Strain to Tests in Areas of High Plastic Strain

2018 ◽  
Author(s):  
Katharine Liu ◽  
Emma Xiao ◽  
Gregory Westwater ◽  
Christopher R. Johnson ◽  
J. Adin Mann
Keyword(s):  
Plastic Strain ◽  
Mesh Refinement ◽  
Sensitivity Study ◽  
Linear Elastic ◽  
Mesh Sensitivity ◽  
Local Mesh Refinement ◽  
Order Of Magnitude ◽  
High Plastic Strain ◽  
Stabilization Technique ◽  
The Impact

The total strain, elastic plus plastic, was measured with strain gages on valve bodies with internal pressure that caused surface yielding. The correlation of the simulated maximum principal strain was compared to strain gage data. A mesh sensitivity study shows that in regions of large plastic strain, mesh elements are required that are an order of magnitude smaller than what is used for linear elastic stress analysis for the same structure. A local mesh refinement was adequate to resolve the local high strain values. Both the location and magnitude of the maximum strain changed with a local mesh refinement. The local mesh refinement requirement was consistent over several structures that were tested. The test and simulation work will be presented along with the mesh sensitivity study. Some results on using an energy stabilization technique to aid convergence will be presented in terms of the impact on the predicted plastic strain.

Numerical modeling and analysis of the noncontacting impulse gas face seals

2018 ◽  
Vol 233 (8) ◽  
pp. 1139-1153
Author(s):  
Slawomir Blasiak
Keyword(s):  
Computer Software ◽  
Surface Modifications ◽  
Mechanical Seals ◽  
Face Surface ◽  
Modeling And Analysis ◽  
C Language ◽  
Model Studies ◽  
Face Seals ◽  
Radial Gap ◽  
The Impact

Noncontacting mechanical seals with various kinds of face surface modifications have established their position in the sealing technique. Over the last few years, a lot of works dedicated to the impact of various surface modifications on the dynamics of working rings have been created. This paper presents model studies regarding relatively unknown noncontacting impulse gas face seals. Here, a mathematical model of impulse gas face seals is developed including the nonlinear Reynolds equation and stator dynamics equations, which were solved simultaneously using numerical methods. An original computer software written in C + + language was developed. A number of numerical tests were conducted and the phenomena occurring in the radial gap during seal operation were analyzed. Final conclusions were drawn and several features were indicated characterizing impulse face seals. It should be emphasized that numerical research on this type of seals has not been published yet. The literature usually presents simplified models for the noncompressible medium, which can be solved with the use of analytical methods.

Sign in / Sign up

Export Citation Format

Share Document