Nanoscale Silica Coated Graphene Oxide and Its Demulsifying Performance in Water-in-oil and Oil-in-water Emulsions

Abstract In present study, GO@SiO2 nanocomposites was prepared by coating nanoscale silica onto graphene oxide (GO). The nanocomposites were characterized with scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (IF-IR). Additionally, the demulsifying performance of the nanocomposites was investigated by the bottle test method. The results showed that GO@SiO2 nanocomposites had a good demulsifying performance both in oil-in-water (O/W) and water-in-oil (W/O) emulsions. When the concentration of GO@SiO2 was 200 ppm in O/W emulsion, the optimal light transmittance of aqueous phase (LTA) and corresponding oil removal rate (ORR) at room temperature could reach 86.9% and 99.48%, respectively. Also, GO@SiO2 had an excellent salt tolerance under acidic condition. Furthermore, GO@SiO2 nanocomposites also could demulsify the W/O emulsion, and the efficiency at 70℃ could reach 80.5% when the concentration was 400 ppm.

Download Full-text

Preparation and Characterizations of Novel Near Room-Temperature Driven Fe/Sr2Bi2O5 Thermocatalyst

Materials Science Forum ◽

10.4028/www.scientific.net/msf.804.63 ◽

2014 ◽

Vol 804 ◽

pp. 63-66

Author(s):

Pei Wu ◽

Xue Gang Luo ◽

Xiao Yan Lin ◽

Ke Li

Keyword(s):

Room Temperature ◽

Negative Temperature Coefficient ◽

Removal Rate ◽

Negative Temperature ◽

X Ray Diffraction ◽

Total Removal ◽

Solid State Method ◽

X Ray ◽

Conventional Solid State Method ◽

Molar Percent

In this study, room-temperature driven thermocatalyst (Fe/Sr2Bi2O5 powder) with negative temperature coefficient resistor (NTC) characteristics was prepared by conventional solid state method at various temperatures. Fe/Sr2Bi2O5 powder was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy EDS. The results indicate that Fe/Sr2Bi2O5 powder was prepared and the Fe has been doped successfully in Sr2Bi2O5. The thermocatalyst powder obtained a particular and stable crystal style, meanwhile, besides, well distributed size and rough surface were also found in regard to the thermocatalyst above. On the other hand, the thermocatalyst reactions show that Fe/Sr2Bi2O5 powder has highest removal rate of degradation under the 0.75% (molar percent) content of Fe at 750 oC. The total removal rate of degradation arrives at 93.8% after 3h at 50 oC. Hence, Fe/Sr2Bi2O5 powder may be a potential thermocatalyst at room-temperature for wastewater treatment in the future.

Download Full-text

A Mild and Efficient Approach for the Reduction of Graphene Oxide

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.652-654.206 ◽

2013 ◽

Vol 652-654 ◽

pp. 206-209

Author(s):

Yu Feng Wang ◽

Chun Hua Han ◽

Bao Liu ◽

Dong Mei Zhao ◽

Dong Yu Zhao ◽

...

Keyword(s):

Graphene Oxide ◽

Photoelectron Spectroscopy ◽

Room Temperature ◽

X Ray Diffraction ◽

X Ray ◽

Efficient Approach ◽

Low Toxicity

A mild and efficient approach for the reduction of graphene oxide by NaHTe is reported in this work. This reductant is of low toxicity and nonvolatile and it reduce GO to graphene at room temperature in 2h. X-ray diffraction results showed that NaHTe can reduce GO completely in shorter time, comparing with hydroxylamine. Furthermore, X-ray photoelectron spectroscopy also indicates the reduction of GO to grapheme.

Download Full-text

An Improvement on Tracking Resistance of Silicone Rubber Filled with Micro-Wollastonite/Gehlenite Synthesized by Solid-State Reaction

Key Engineering Materials ◽

10.4028/www.scientific.net/kem.902.107 ◽

2021 ◽

Vol 902 ◽

pp. 107-111

Author(s):

Pattarabordee Khaigunha ◽

Tanakorn Wongwuttanasatian

Keyword(s):

Silicone Rubber ◽

Room Temperature ◽

Raw Materials ◽

Filler Loading ◽

Test Method ◽

X Ray Diffraction ◽

X Ray ◽

Surface Tracking ◽

Long Time ◽

Scanning Electron

Enhancement of the room temperature vulcanization silicone rubber (RTV) tracking resistance with various filler loadings of synthesized wollastonite against electrical surface tracking was prepared. The X-ray diffraction (XRD), Scanning electron microscope (SEM), and X-ray fluorescent (XRF) techniques were involved in characterizing the synthesized substances. The test method IEC-60587 standard was employed to evaluate the surface tracking resistance. The results obtained from the XRF technique confirmed that the raw materials could be synthesized for wollastonite, while the XRD and SEM techniques revealed the formation of wollastonite (CaSiO3) associated with gehlenite (Ca2Al2SiO7). Moreover, it was found that the electrical surface tracking resistance of composite insulation takes a long time to track when the filler loading is increased more than 5 phr.

Download Full-text

Electron Microscopy of Human Gallstones

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100065523 ◽

1971 ◽

Vol 29 ◽

pp. 296-297

Author(s):

C. Wolpers ◽

R. Blaschke

Keyword(s):

Electron Microscopy ◽

Room Temperature ◽

Bile Pigment ◽

X Ray Diffraction ◽

Triclinic Crystal System ◽

X Ray ◽

Follow Up Study ◽

Infra Red ◽

Main Components

Scanning microscopy was used to study the surface of human gallstones and the surface of fractures. The specimens were obtained by operation, washed with water, dried at room temperature and shadowcasted with carbon and aluminum. Most of the specimens belong to patients from a series of X-ray follow-up study, examined during the last twenty years. So it was possible to evaluate approximately the age of these gallstones and to get information on the intensity of growing and solving.Cholesterol, a group of bile pigment substances and different salts of calcium, are the main components of human gallstones. By X-ray diffraction technique, infra-red spectroscopy and by chemical analysis it was demonstrated that all three components can be found in any gallstone. In the presence of water cholesterol crystallizes in pane-like plates of the triclinic crystal system.

Download Full-text

Electron Microscope study of commensurate-incommensurate phase transition in BaZnGeO4

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100173996 ◽

1990 ◽

Vol 48 (4) ◽

pp. 172-173

Author(s):

Naoki Yamamoto ◽

Makoto Kikuchi ◽

Tooru Atake ◽

Akihiro Hamano ◽

Yasutoshi Saito

Keyword(s):

Phase Transition ◽

Electron Microscope Study ◽

Room Temperature ◽

Hexagonal Lattice ◽

Ferroelectric Materials ◽

Temperature Phase ◽

X Ray Diffraction ◽

X Ray ◽

Periodic Arrays ◽

Modulation Wave Vector

BaZnGeO4 undergoes many phase transitions from I to V phase. The highest temperature phase I has a BaAl2O4 type structure with a hexagonal lattice. Recent X-ray diffraction study showed that the incommensurate (IC) lattice modulation appears along the c axis in the III and IV phases with a period of about 4c, and a commensurate (C) phase with a modulated period of 4c exists between the III and IV phases in the narrow temperature region (—58°C to —47°C on cooling), called the III' phase. The modulations in the IC phases are considered displacive type, but the detailed structures have not been studied. It is also not clear whether the modulation changes into periodic arrays of discommensurations (DC’s) near the III-III' and IV-V phase transition temperature as found in the ferroelectric materials such as Rb2ZnCl4.At room temperature (III phase) satellite reflections were seen around the fundamental reflections in a diffraction pattern (Fig.1) and they aligned along a certain direction deviated from the c* direction, which indicates that the modulation wave vector q tilts from the c* axis. The tilt angle is about 2 degree at room temperature and depends on temperature.

Download Full-text

Xenon Trioxide Adducts of O-Donor Ligands; [(CH3)2CO]3XeO3, [(CH3)2SO]3(XeO3)2, (C5H5NO)3(XeO3)2, and [(C6H5)3PO]2XeO3

10.26434/chemrxiv.7092263.v1 ◽

2018 ◽

Author(s):

Katherine Marczenko ◽

James Goettel ◽

Gary Schrobilgen

Keyword(s):

Room Temperature ◽

Triphenylphosphine Oxide ◽

Donor Ligands ◽

Mechanical Shock ◽

X Ray Diffraction ◽

X Ray ◽

Oxygen Coordination ◽

Xenon Trioxide ◽

Distorted Octahedra ◽

Coordination Spheres

Oxygen coordination to the Xe(VI) atom of XeO3 was observed in its adducts with triphenylphosphine oxide, dimethylsulfoxide, pyridine-N-oxide, and acetone. The crystalline adducts were characterized by low-temperature, single-crystal X-ray diffraction and Raman spectroscopy. Unlike solid XeO3, which detonates when mechanically or thermally shocked, the solid [(C6H5)3PO]2XeO3, [(CH3)2SO]3(XeO3)2, and (C5H5NO)3(XeO3)2 adducts are insensitive to mechanical shock, but undergo rapid deflagration when ignited by a flame. Both [(C6H5)3PO]2XeO3 and (C5H5NO)3(XeO3)2 are air-stable whereas [(CH3)2SO]3(XeO3)2 slowly decomposes over several days and [(CH3)2CO]3XeO3 undergoes adduct dissociation at room temperature. The xenon coordination sphere of [(C6H5)3PO]2XeO3 is a distorted square pyramid which provides the first example of a five-coordinate XeO3 adduct. The xenon coordination spheres of the remaining adducts are distorted octahedra comprised of three Xe---O secondary contacts that are approximately trans to the primary Xe–O bonds of XeO3. Quantum-chemical calculations were used to assess the Xe---O adduct bonds, which are predominantly electrostatic σ-hole bonds between the nucleophilic oxygen atoms of the bases and the σ-holes of the xenon atoms.

Download Full-text

Effect of trytophan as dopant on potassium acid phthalate single crystals

10.31221/osf.io/cn28k ◽

2019 ◽

Author(s):

Chem Int

Keyword(s):

Single Crystals ◽

Room Temperature ◽

Visible Region ◽

X Ray Diffraction ◽

X Ray ◽

Slow Evaporation Technique ◽

Absorption Studies ◽

Evaporation Technique ◽

Potassium Acid Phthalate ◽

Acid Phthalate

Optically transparent single crystals of potassium acid phthalate (KAP, 0.5 g) 0.05 g and 0.1 g (1 and 2 mol %) trytophan were grown in aqueous solution by slow evaporation technique at room temperature. Single crystal X- ray diffraction analysis confirmed the changes in the lattice parameters of the doped crystals. The presence of functional groups in the crystal lattice has been determined qualitatively by FTIR analysis. Optical absorption studies revealed that the doped crystals possess very low absorption in the entire visible region. The dielectric constant has been studied as a function of frequency for the doped crystals. The thermal stability was evaluated by TG-DSC analysis.

Download Full-text

Structural and Enhanced Optical Properties of Stabilized γ‒Bi2O3 Nanoparticles: Effect of Oxygen Ion Vacancies

Nanomaterials ◽

10.3390/nano10061023 ◽

2020 ◽

Vol 10 (6) ◽

pp. 1023 ◽

Cited By ~ 2

Author(s):

Ashish Chhaganlal Gandhi ◽

Chia-Liang Cheng ◽

Sheng Yun Wu

Keyword(s):

Room Temperature ◽

Excess Oxygen ◽

Ambient Atmosphere ◽

Photoluminescence Spectra ◽

X Ray Diffraction ◽

X Ray ◽

Band Emission ◽

Oxygen Ion ◽

Integrated Intensity ◽

Effect Of Oxygen

We report the synthesis of room temperature (RT) stabilized γ–Bi2O3 nanoparticles (NPs) at the expense of metallic Bi NPs through annealing in an ambient atmosphere. RT stability of the metastable γ–Bi2O3 NPs is confirmed using synchrotron radiation powder X-ray diffraction and Raman spectroscopy. γ–Bi2O3 NPs exhibited a strong red-band emission peaking at ~701 nm, covering 81% integrated intensity of photoluminescence spectra. Our findings suggest that the RT stabilization and enhanced red-band emission of γ‒Bi2O3 is mediated by excess oxygen ion vacancies generated at the octahedral O(2) sites during the annealing process.

Download Full-text

Mechanical Alloying Behavior in the Nb-Si, Ta-Si, and Nb-Ta-Si Systems

MRS Proceedings ◽

10.1557/proc-133-415 ◽

1988 ◽

Vol 133 ◽

Cited By ~ 3

Author(s):

K. S. Kumar ◽

S. K. Mannan

Keyword(s):

High Temperature ◽

Mechanical Alloying ◽

Mechanical Milling ◽

Room Temperature ◽

Crystalline Compound ◽

X Ray Diffraction ◽

X Ray ◽

Β Phase ◽

Α Phase

ABSTRACTThe mechanical alloying behavior of elemental powders in the Nb-Si, Ta-Si, and Nb-Ta-Si systems was examined via X-ray diffraction. The line compounds NbSi2 and TaSi2 form as crystalline compounds rather than amorphous products, but Nb5Si3 and Ta5Si3, although chemically analogous, respond very differently to mechanical milling. The Ta5Si3 composition goes directly from elemental powders to an amorphous product, whereas Nb5Si3 forms as a crystalline compound. The Nb5Si3 compound consists of both the tetragonal room-temperature α phase (c/a = 1.8) and the tetragonal high-temperature β phase (c/a = 0.5). Substituting increasing amounts of Ta for Nb in Nb5Si3 initially stabilizes the α-Nb5Si3 structure preferentially, and subsequently inhibits the formation of a crystalline compound.

Download Full-text

Synthesis of Magnetic Ferrocene-Containing Polymer with Photothermal Effects for Rapid Degradation of Methylene Blue

Polymers ◽

10.3390/polym13040558 ◽

2021 ◽

Vol 13 (4) ◽

pp. 558

Author(s):

Wenhui Zhu ◽

Caiyun Zhang ◽

Yali Chen ◽

Qiliang Deng

Keyword(s):

Methylene Blue ◽

Photoelectron Spectroscopy ◽

Room Temperature ◽

Degradation Rate ◽

Model Compound ◽

Vibrating Sample Magnetometer ◽

Simulated Sunlight ◽

X Ray Diffraction ◽

X Ray ◽

Ft Ir

Photothermal materials are attracting more and more attention. In this research, we synthesized a ferrocene-containing polymer with magnetism and photothermal properties. The resulting polymer was characterized by Fourier-transform infrared (FT-IR), vibrating sample magnetometer (VSM), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Its photo-thermocatalytic activity was investigated by choosing methylene blue (MB) as a model compound. The degradation percent of MB under an irradiated 808 nm laser reaches 99.5% within 15 min, and the degradation rate is 0.5517 min−1, which is 145 times more than that of room temperature degradation. Under irradiation with simulated sunlight, the degradation rate is 0.0092 min−1, which is approximately 2.5 times more than that of room temperature degradation. The present study may open up a feasible route to degrade organic pollutants.

Download Full-text