scholarly journals Evaluation of Seasonal Variability of First-order Ionospheric Delay Correction at L5 and S1 Frequencies Using Dual-frequency Navic System

2021 ◽  
Author(s):  
Sharat chandra Bhardwaj ◽  
Anurag Vidyarthi ◽  
Bhajan Singh Jassal ◽  
Ashish kumar Shukla
Keyword(s):  
Seasonal Variability ◽  
Ionospheric Delay ◽  
Electron Content ◽  
Dual Frequency ◽  
Satellite Constellations ◽  
Total Electron ◽  
First Order ◽  
Seasonal Characteristics ◽  
Geosynchronous Satellites ◽  
Delay Correction

Abstract For the precise positioning application it is important to determine and eliminate the positioning error introduced by various sources such as the ionosphere. To develop a standalone precise navigation system, India has launched the seven satellite constellations of NavIC (Navigation with Indian Constellation) system to provide precision positioning over India and surrounded landmass. Since the ionospheric delay depends on the frequency of the satellite signal and NavIC systems work at different frequencies (L5 and S1) than GPS systems (L1 and L2), it is not possible to use the GPS data-driven study for NavIC based location calculations directly. Thus there is a need for a specialized ionospheric study for NavIC systems. In addition, the ionospheric delay is directly proportional to Slant Total Electron Content (STEC) which is dependent upon diurnal and seasonal solar activity. To achieve accurate positioning facilities, there is also a need for evaluation for seasonal variability of ionospheric delay correction for NavIC receivers. This paper deals with the STEC estimation; its smoothing, and removal of instrumental biases from STEC. The determined true STEC has been used to determine first-order ionospheric delay at L5 and S1 frequencies. The delay at S1 has been found less (2 to 7m) as compared to L5 (10 to 30m). Furthermore, the seasonal variability of ionospheric delay has been analyzed using about 19 months of data (from June 2017 to December 2018) and found that the ionospheric delay follows unique seasonal characteristics which can be utilized for delay modeling. It has been also observed that the geostationary satellites of the NavIC system are more appropriate than geosynchronous satellites for ionospheric related studies.

Performance Evaluation of USTEC Product for Single-Frequency Precise Point Positioning

GEOMATICA ◽  
2013 ◽  
Vol 67 (4) ◽  
pp. 253-257 ◽  
Author(s):  
Mahmoud Abd El-Rahman ◽  
Ahmed El-Rabbany
Keyword(s):  
Total Electron Content ◽  
Precise Point Positioning ◽  
Ionospheric Delay ◽  
Single Frequency ◽  
Electron Content ◽  
Dual Frequency ◽  
Total Electron ◽  
Gps Receivers ◽  
Mitigation Techniques ◽  
Point Positioning

Geodetic-grade dual-frequency GPS receivers are typically used for precise point positioning (PPP). Unfortunately, these receiver systems are expensive and may not provide a cost-effective solution in many instances. The use of low-cost single-frequency GPS receivers, on the other hand, are limited by the effect of ionospheric delay. A number of mitigation techniques have been proposed to account for the effect of ionospheric delay for single-frequency GPS users. Unfortunately, however, those mitigation techniques are not suitable for PPP. More recently, the U.S. Total Electron Content (USTEC) product has been developed by the National Oceanic and Atmospheric Administration (NOAA), which describes the ionospheric total electron content in high resolution over most of North America. This paper investigates the performance of USTEC and studies its effect on single-frequency PPP solution. A performance comparison with two widely-used ionospheric mitigation models is also presented.

scholarly journals Vertical Ionosphere Delay Estimation using Zero Difference GPS Phase Observation

2018 ◽  
Author(s):  
Ahmed Elsayed ◽  
Ahmed Sedeek ◽  
Mohamed Doma ◽  
Mostafa Rabah
Keyword(s):  
Carrier Phase ◽  
Free Carrier ◽  
Error Modeling ◽  
Ionospheric Delay ◽  
Electron Content ◽  
Gps Receiver ◽  
Dual Frequency ◽  
Total Electron ◽  
Longitudinal Gradients ◽  
Least Squares Adjustment

Abstract. An apparent delay is occurred in GPS signal due to both refraction and diffraction caused by the atmosphere. The second region of the atmosphere is the ionosphere. The ionosphere is significantly related to GPS and the refraction it causes in GPS signal is considered one of the main source of errors which must be eliminated to determine accurate positions. GPS receiver networks have been used for monitoring the ionosphere for a long time. The ionospheric delay is the most predominant of all the error sources. This delay is a function of the total electron content (TEC). Because of the dispersive nature of the ionosphere, one can estimate the ionospheric delay using the dual frequency GPS. In the current research our primary goal is applying Precise Point Positioning (PPP) observation for accurate ionosphere error modeling, by estimating Ionosphere delay using carrier phase observations from dual frequency GPS receiver. The proposed algorithm was written using MATLAB. The proposed Algorithm depends on the geometry-free carrier-phase observations after detecting cycle slip to estimates the ionospheric delay using a spherical ionospheric shell model, in which the vertical delays are described by means of a zenith delay at the station position and latitudinal and longitudinal gradients. Geometry-free carrier-phase observations were applied to avoid unwanted effects of pseudorange measurements, such as code multipath. The ionospheric estimation in this algorithm is performed by means of sequential least-squares adjustment. Finally, an adaptable user interface MATLAB software are capable of estimating ionosphere delay, ambiguity term and ionosphere gradient accurately.

Vertical ionospheric delay estimation for single-receiver operation

2019 ◽  
Vol 13 (2) ◽  
pp. 81-91 ◽  
Author(s):  
Ahmed Elsayed ◽  
Ahmed Sedeek ◽  
Mohamed Doma ◽  
Mostafa Rabah
Keyword(s):  
Carrier Phase ◽  
Free Carrier ◽  
Error Modeling ◽  
Ionospheric Delay ◽  
Electron Content ◽  
Gps Receiver ◽  
Dual Frequency ◽  
Total Electron ◽  
Longitudinal Gradients ◽  
Least Squares Adjustment

Abstract An apparent delay is occurred in GPS signal due to both refraction and diffraction caused by the atmosphere. The second region of the atmosphere is the ionosphere. The ionosphere is significantly related to GPS and the refraction it causes in GPS signal is considered one of the main source of errors which must be eliminated to determine accurate positions. GPS receiver networks have been used for monitoring the ionosphere for a long time. The ionospheric delay is the most predominant of all the error sources. This delay is a function of the total electron content (TEC). Because of the dispersive nature of the ionosphere, one can estimate the ionospheric delay using the dual frequency GPS. In the current research our primary goal is applying Precise Point Positioning (PPP) observation for accurate ionosphere error modeling, by estimating Ionosphere delay using carrier phase observations from dual frequency GPS receiver. The proposed algorithm was written using MATLAB and was named VIDE program. The proposed Algorithm depends on the geometry-free carrier-phase observations after detecting cycle slip to estimates the ionospheric delay using a spherical ionospheric shell model, in which the vertical delays are described by means of a zenith delay at the station position and latitudinal and longitudinal gradients. Geometry-free carrier-phase observations were applied to avoid unwanted effects of pseudorange measurements, such as code multipath. The ionospheric estimation in this algorithm is performed by means of sequential least-squares adjustment. Finally, an adaptable user interface MATLAB software are capable of estimating ionosphere delay, ambiguity term and ionosphere gradient accurately.

scholarly journals Functional model modification of precise point positioning considering the time-varying code biases of a receiver

2021 ◽  
Vol 2 (1) ◽  
Author(s):  
Baocheng Zhang ◽  
Chuanbao Zhao ◽  
Robert Odolinski ◽  
Teng Liu
Keyword(s):  
Precise Point Positioning ◽  
Functional Model ◽  
Geodetic Network ◽  
Temporal Variations ◽  
Gps Data ◽  
Electron Content ◽  
Time Varying ◽  
Dual Frequency ◽  
Total Electron ◽  
Point Positioning

AbstractPrecise Point Positioning (PPP), initially developed for the analysis of the Global Positing System (GPS) data from a large geodetic network, gradually becomes an effective tool for positioning, timing, remote sensing of atmospheric water vapor, and monitoring of Earth’s ionospheric Total Electron Content (TEC). The previous studies implicitly assumed that the receiver code biases stay constant over time in formulating the functional model of PPP. In this contribution, it is shown this assumption is not always valid and can lead to the degradation of PPP performance, especially for Slant TEC (STEC) retrieval and timing. For this reason, the PPP functional model is modified by taking into account the time-varying receiver code biases of the two frequencies. It is different from the Modified Carrier-to-Code Leveling (MCCL) method which can only obtain the variations of Receiver Differential Code Biases (RDCBs), i.e., the difference between the two frequencies’ code biases. In the Modified PPP (MPPP) model, the temporal variations of the receiver code biases become estimable and their adverse impacts on PPP parameters, such as ambiguity parameters, receiver clock offsets, and ionospheric delays, are mitigated. This is confirmed by undertaking numerical tests based on the real dual-frequency GPS data from a set of global continuously operating reference stations. The results imply that the variations of receiver code biases exhibit a correlation with the ambient temperature. With the modified functional model, an improvement by 42% to 96% is achieved in the Differences of STEC (DSTEC) compared to the original PPP model with regard to the reference values of those derived from the Geometry-Free (GF) carrier phase observations. The medium and long term (1 × 104 to 1.5 × 104 s) frequency stability of receiver clocks are also significantly improved.

scholarly journals Accuracy Analysis of International Reference Ionosphere 2016 and NeQuick2 in the Antarctic

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1551
Author(s):  
Zihuai Guo ◽  
Yibin Yao ◽  
Jian Kong ◽  
Gang Chen ◽  
Chen Zhou ◽  
...  
Keyword(s):  
Solar Radiation ◽  
International Reference Ionosphere ◽  
Electron Content ◽  
Observation Data ◽  
Dual Frequency ◽  
Total Electron ◽  
International Reference ◽  
Antarctic Continent ◽  
The Antarctic ◽  
Frequency Observation

Global navigation satellite system (GNSS) can provide dual-frequency observation data, which can be used to effectively calculate total electron content (TEC). Numerical studies have utilized GNSS-derived TEC to evaluate the accuracy of ionospheric empirical models, such as the International Reference Ionosphere model (IRI) and the NeQuick model. However, most studies have evaluated vertical TEC rather than slant TEC (STEC), which resulted in the introduction of projection error. Furthermore, since there are few GNSS observation stations available in the Antarctic region and most are concentrated in the Antarctic continent edge, it is difficult to evaluate modeling accuracy within the entire Antarctic range. Considering these problems, in this study, GNSS STEC was calculated using dual-frequency observation data from stations that almost covered the Antarctic continent. By comparison with GNSS STEC, the accuracy of IRI-2016 and NeQuick2 at different latitudes and different solar radiation was evaluated during 2016–2017. The numerical results showed the following. (1) Both IRI-2016 and NeQuick2 underestimated the STEC. Since IRI-2016 utilizes new models to represent the F2-peak height (hmF2) directly, the IRI-2016 STEC is closer to GNSS STEC than NeQuick2. This conclusion was also confirmed by the Constellation Observing System for Meteorology Ionosphere and Climate (COSMIC) occultation data. (2) The differences in STEC of the two models are both normally distributed, and the NeQuick2 STEC is systematically biased as solar radiation increases. (3) The root mean square error (RMSE) of the IRI-2016 STEC is smaller than that of the NeQuick2 model, and the RMSE of the two modeling STEC increases with solar radiation intensity. Since IRI-2016 relies on new hmF2 models, it is more stable than NeQuick2.

scholarly journals Seasonal dependence of the "forecast parameter" based on the EIA characteristics for the prediction of Equatorial Spread F (ESF)

2008 ◽  
Vol 26 (7) ◽  
pp. 1751-1757 ◽  
Author(s):  
S. V. Thampi ◽  
S. Ravindran ◽  
T. K. Pant ◽  
C. V. Devasia ◽  
R. Sridharan
Keyword(s):  
Seasonal Variability ◽  
Seasonal Pattern ◽  
Onset Time ◽  
Critical Value ◽  
Latitudinal Gradients ◽  
Electron Content ◽  
Total Electron ◽  
Equatorial Spread F ◽  
Spread F ◽  
Definite Role

Abstract. In an earlier study, Thampi et al. (2006) have shown that the strength and asymmetry of Equatorial Ionization Anomaly (EIA), obtained well ahead of the onset time of Equatorial Spread F (ESF) have a definite role on the subsequent ESF activity, and a new "forecast parameter" has been identified for the prediction of ESF. This paper presents the observations of EIA strength and asymmetry from the Indian longitudes during the period from August 2005–March 2007. These observations are made using the line of sight Total Electron Content (TEC) measured by a ground-based beacon receiver located at Trivandrum (8.5° N, 77° E, 0.5° N dip lat) in India. It is seen that the seasonal variability of EIA strength and asymmetry are manifested in the latitudinal gradients obtained using the relative TEC measurements. As a consequence, the "forecast parameter" also displays a definite seasonal pattern. The seasonal variability of the EIA strength and asymmetry, and the "forecast parameter" are discussed in the present paper and a critical value for has been identified for each month/season. The likely "skill factor" of the new parameter is assessed using the data for a total of 122 days, and it is seen that when the estimated value of the "forecast parameter" exceeds the critical value, the ESF is seen to occur on more than 95% of cases.

scholarly journals Analisis Total Electron Content (TEC) Menggunakan Continous Wavelet Transform Sebagai Indikator Prekursor Gempa Bumi Di Wilayah Provinsi Bengkulu

2019 ◽  
Vol 9 (2) ◽  
pp. 27-33
Author(s):  
Laksamana Agung Aprillo ◽  
Hendy Santosa ◽  
Faisal Hadi
Keyword(s):  
Wavelet Transform ◽  
Standard Deviation ◽  
Total Electron Content ◽  
Electromagnetic Waves ◽  
Electron Content ◽  
Observation Data ◽  
Dual Frequency ◽  
Total Electron ◽  
Gps Observation ◽  
Large Earthquakes

ABSTRACT Bengkulu is one of 34 provinces in Indonesia which is a megathrust region. So Bengkulu province is often hit by many large earthquakes with shallow depth. TEC anomaly was analyzed based on three electromagnetic waves radiated by an earthquake. The total electron content (TEC) anomaly is seen through the global positioning system (GPS) dual-frequency radio signal data. The continuous wavelet transform (CWT) method is used to divide the signal analysis into several sections according to the electromagnetic wave frequency range of acoustic (2.5 mHz) -3 mHz), gravity waves (1 mHz-2.8 mHz) and rayleigh waves (5 mHz-33 mHz). GPS observation data for 9 days is calculated using the Standard deviation (2?) method to see trends in data changes. The analysis shows anomalies in the September 12 2007 earthquake (7.9 Mw), the March 5 2010 earthquake (6.3 Mw) and the August 4 2011 earthquake (6.0 Mw). Anomalies are detected 1 to 5 hours before an earthquake occurs. TEC anomalies that occur may be related to the process of preseismic before the earthquake and may be an early sign of an earthquake.Keyword: earthquake, total electron content, continous wavelet transform, standard deviation

Validating the impact of various ionosphere correction on mid to long baselines and point positioning using GPS dual-frequency receivers

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Alaa A. Elghazouly ◽  
Mohamed I. Doma ◽  
Ahmed A. Sedeek
Keyword(s):  
Geomagnetic Storms ◽  
Global Navigation Satellite Systems ◽  
Electron Content ◽  
Assessment Procedure ◽  
Vertical Total Electron Content ◽  
Dual Frequency ◽  
Total Electron ◽  
Satellite Systems ◽  
Point Positioning ◽  
The Impact

Abstract Due to the ionosphere delay, which has become the dominant GPS error source, it is crucial to remove the ionospheric effect before estimating point coordinates. Therefore, different agencies started to generate daily Global Ionosphere Maps (GIMs); the Vertical Total Electron Content (VTEC) values represented in GIMs produced by several providers can be used to remove the ionosphere error from observations. In this research, An analysis will be carried with three sources for VTEC maps produced by the Center for Orbit Determination in Europe (CODE), Regional TEC Mapping (RTM), and the International Reference Ionosphere (IRI). The evaluation is focused on the effects of a specific ionosphere GIM correction on the precise point positioning (PPP) solutions. Two networks were considered. The first network consists of seven Global Navigation Satellite Systems (GNSS) receivers from (IGS) global stations. The selected test days are six days, three of them quiet, and three other days are stormy to check the influence of geomagnetic storms on relative kinematic positioning solutions. The second network is a regional network in Egypt. The results show that the calculated coordinates using the three VTEC map sources are far from each other on stormy days rather than on quiet days. Also, the standard deviation values are large on stormy days compared to those on quiet days. Using CODE and RTM IONEX file produces the most precise coordinates after that the values of IRI. The elimination of ionospheric biases over the estimated lengths of many baselines up to 1000 km has resulted in positive findings, which show the feasibility of the suggested assessment procedure.

scholarly journals Assessing Global Ionosphere TEC Maps with Satellite Altimetry and Ionospheric Radio Occultation Observations

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5489 ◽  
Author(s):  
Wei Li ◽  
Longqiang Huang ◽  
Shaocheng Zhang ◽  
Yanju Chai
Keyword(s):  
High Latitude ◽  
Satellite Altimetry ◽  
Radio Occultation ◽  
Lower Latitude ◽  
Electron Content ◽  
Dual Frequency ◽  
International Gnss Service ◽  
Night Time ◽  
Scaling Factors ◽  
Total Electron

As global navigation satellite system (GNSS)stations are sparsely distributed in oceanic area, oceanic areas usually have lower precision than continental areas on a global ionosphere maps (GIM). On the other hand, space-borne observations like satellite altimetry (SA) and ionospheric radio occultation (IRO) have substantial dual-frequency observations in oceanic areas, which could be used for total electron content (TEC) retrieval. In this paper, the Jason-2 SA and Constellation Observing System for Meteorology, Ionosphere, and Climate (COSMIC) IRO products were used to assess the precision of IGS GIM products. Both the systematic biases and scaling factors between the international GNSS service (IGS) GIM TEC and space-borne TEC were calculated, and the statistical results show that the biases and the scaling factors obviously vary under different temporal-spatial conditions. This analysis shows that these differences are variable with diurnal and latitude factors, that is, the differences in biases during the day time are higher than those during the night time, and larger biases are experienced at lower latitude areas than at high latitude areas. The results also show that in the southern hemisphere middle-high latitude area and some other central oceanic areas, the space-borne TEC values are even higher than GIM TEC values. As the precision of space-borne TEC should be evenly distributed around different areas on Earth, it can be explain that the TEC in these areas is undervalued by the current GIM model, and the space-borne SA and IRO techniques could be used as complementary observations to improve the accuracy and reliability of TEC values in these areas.

Sign in / Sign up

Export Citation Format

Share Document