scholarly journals The Evaluation of apically extruded debris during root canal preparation using Pro-Taper Universal, ProTaper Gold and Reciproc Blue system: An in-vitro comparative Study

2020 ◽  
Vol 6 (2) ◽  
pp. 11-15
Author(s):  
Padma Chandra ◽  
Rajesh Prasad ◽  
Surendra Kumar Mishra ◽  
Jagdish Chandra
Keyword(s):  
File System ◽  
In Vitro Study ◽  
Nickel Titanium ◽  
Root Canal Preparation ◽  
Human Teeth ◽  
Significance Level ◽  
Significant Difference ◽  
Bonferroni Test ◽  
Post Hoc

ABSTRACT Aims & Objectives: The purpose of this study was to compare the amount of apically extruded debris with four nickel-titanium instruments i.e ProTaper Universal, ProTaper Gold, and Reciproc Blue system, Hand K file System. Methods: Eighty extracted single-rooted mandibular premolar human teeth were randomly assigned to 4 groups (n = 20). The canals were instrumented using 1 of the following instruments: ProTaper Universal, ProTaper Gold, and Reciproc Blue system, Hand K file System. Apically extruded debris during instrumentation was collected into preweighed Eppendorf tubes. The weight of the extruded debris was calculated by subtracting the weight of the empty tubes from that of the tubes containing the debris. The data were analyzed statistically using the analysis of variance (ANOVA) and Post-hoc bonferroni test at a significance level of P < .05. Results: All the instrumentation systems resulted in production of extruded debris. The amount of extruded debris was significantly more in Hand K file than PTU, PTG and Reciproc Blue (P<0.05). The PTU system was associated with significantly more extruded debris than the PTG(P=0.041), Reciproc Blue systems (P=`0.011), whereas no significant difference was found in the amount of the debris extruded between PTG and Reciproc Blue (P=0.271). The amount of extruded debris was least in Reciproc Blue in comparison to all used system. Conclusions: Within the limitations of this in vitro study, the amount of apically extruded debris registered for the different files tested was highest for hand file, Protaper Universal, followed by the ProTaper Gold and least in Reciproc Blue.

scholarly journals INFLUÊNCIA DA MODIFICAÇÃO DA BASE DE COLAGEM E DA CONTAMINAÇÃO SALIVAR NA RESISTÊNCIA DE UNIÃO DE TUBOS ORTODÔNTICOS COLADOS AO ESMALTE HUMANO

2021 ◽  
Vol 58 (1) ◽  
pp. eUJ3657
Author(s):  
Germano Brandão ◽  
◽  
Liliana Ávila Maltagliati ◽  
Ana Carla Raphaelli Nahás-Scocate ◽  
Murilo Matias ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Statistical Significance ◽  
Testing Machine ◽  
In Vitro Study ◽  
Metal Mesh ◽  
Human Teeth ◽  
Significance Level ◽  
Significant Difference

The objective of this in vitro study was to assess and compare the shear bond strength of conventional and modified orthodontic tubes bonded to the surface of dry and saliva-contaminated enamel. The sample consisted of 40 human teeth, which were randomly divided into four groups according to attachment base and presence or absence of saliva contamination as follows: Group CB, conventional orthodontic tubes without salivary contamination; Group CB-S, conventional orthodontic tubes with salivary contamination; Groups BM, orthodontic tubes modified by welding a metal mesh to their base without salivary contamination; and Group BM-S, modified orthodontic tubes with salivary contamination. Shear bond strength test was performed in a universal testing machine and analysis of the adhesive remnant index (ARI) by optical microscopy. Two-way ANOVA was used, followed by Tukey’s test at a statistical significance level of 5%. The ARI results were analysed descriptively. There was statistically significant difference between the groups regarding the shear bond strength values, with conventional tubes presenting significantly higher values (P < 0.05). In addition, the presence of salivary contamination interfered negatively with the behaviour of conventional tubes only (P < 0.05). Shear bond strength was not improved by increasing the area of the orthodontic tubes. Moreover, salivary contamination influenced negatively the SBS values, but only when conventional tubes were used.

scholarly journals The effect of one-step and multi-step polishing systems on the surface roughness and microhardness of novel resin composites

2012 ◽  
Vol 06 (02) ◽  
pp. 198-205 ◽  
Author(s):  
Ugur Erdemir ◽  
Hande Sar Sancakli ◽  
Esra Yildiz
Keyword(s):  
Surface Roughness ◽  
Resin Composite ◽  
In Vitro Study ◽  
Resin Composites ◽  
Significance Level ◽  
Significant Difference ◽  
One Step ◽  
Wet Ground ◽  
Post Hoc

ABSTRACTObjectives: The objective of this in vitro study was to evaluate the surface roughness and microhardness of three novel resin composites containing nanoparticles after polishing with one-step and conventional multi-step polishing systems.Methods: A total of 126 specimens (10 X 2 mm) were prepared in a metal mold using three nanocomposites (Filtek Supreme XT, Ceram-X, and Grandio), 21 specimens of each resin composite for both tests (n=63 for each test). Following light curing, seven specimens from each group received no polishing treatment and served as controls for both tests. The specimens were randomly polished using PoGo and Sof-Lex systems for 30 seconds after being wet-ground with 1200-grit silicon carbide paper. The mean surface roughness of each polished specimen was determined with a profilometer. The microhardness was determined using a Vickers hardness measuring instrument with a 200-g load and 15 seconds dwell time. The data were analyzed using the Kruskal-Wallis test and the post hoc Dunn's multiple comparison tests at a significance level of .05.Results: Among all materials, the smoothest surfaces were obtained under a matrix strip (control) (P<.05). There were no statistically significant differences among polishing systems in the resin composites for surface roughness (P>.05). The lowest hardness values for the three resin composites were obtained with a matrix strip, and there was a statistically significant difference compared with other polishing systems (P<.05) whereas no statistically significant differences were observed between the polishing systems (P<.05).Conclusion: The current one-step polishing system appears to be as effective as multi-step systems and may be preferable for polishing resin composite restorations. (Eur J Dent 2012;6:198-205)

scholarly journals The Antibacterial Efficacy of Biopure MTAD in Root Canal Contaminated with Enterococcus faecalis

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Blerim Kamberi ◽  
Donika Bajrami ◽  
Miranda Stavileci ◽  
Shuhreta Omeragiq ◽  
Fatmir Dragidella ◽  
...  
Keyword(s):  
In Vitro Study ◽  
Sodium Hypochlorite Solution ◽  
Antibacterial Efficacy ◽  
Human Teeth ◽  
Exact Test ◽  
Hypochlorite Solution ◽  
Root Canals ◽  
Significant Difference ◽  
Level Of Significance

Aim. The purpose of this in vitro study was to assess the antimicrobial efficacy of Biopure MTAD against E. faecalis in contaminated root canals. Materials and Methods. Forty-two single rooted extracted human teeth were inoculated with E. faecalis and incubated for four weeks. The samples were divided in two control and five experimental groups irrigated with 1.5% sodium hypochlorite solution (NaOCl); 3% NaOCl; BioPure MTAD; 1.5% NaOCl/17% EDTA; or 3% NaOCl/17% EDTA. After a one-week incubation, complete disinfection was confirmed by the absence of turbidity in the incubation media. Dentin shavings were taken from samples with no turbidity to verify whether E. faecalis was present in dentin tubules. Results were analyzed statistically using Fisher's exact test, with the level of significance set at . Results. Statistical analysis of the data obtained at Day 7 and after dentin shaving analysis showed that BioPure MTAD had significantly greater antibacterial activity than 1.5% NaOCl, 1.5% NaOCl/17% EDTA and 3% NaOCl/17% EDTA. No significant difference was detected between MTAD and 3% NaOCl. Conclusions. These findings suggest that BioPure MTAD possesses superior bactericidal activity compared with NaOCl and EDTA against E. faecalis.

scholarly journals Effectiveness of a silicon-based root canal sealer for filling of simulated lateral canals

2007 ◽  
Vol 18 (1) ◽  
pp. 20-23 ◽  
Author(s):  
João Vicente Baroni Barbizam ◽  
Matheus Souza ◽  
Doglas Cecchin ◽  
Jakob Dabbel
Keyword(s):  
Root Canal ◽  
In Vitro Study ◽  
Root Canal Sealer ◽  
Human Teeth ◽  
Significance Level ◽  
Working Length ◽  
Group 3 ◽  
Group 2 ◽  
Silicon Based

The purpose of this in vitro study was to evaluate the ability of a silicon-based root canal sealer, compared to zinc oxide and eugenol and an epoxy resin-based sealers, for filling of simulated lateral canals. Thirty extracted single-rooted human teeth were selected, conventional access was made and the working length was established 1 mm from the apical foramen. Three simulated lateral canals, one in each root third (coronal, middle and apical) were prepared in both the mesial and distal surfaces of each tooth using a size 15 reamer adapted to a low-speed handpiece. Each root canal was instrumented using ProTaper rotary files up to file F3 at the working length, and then irrigated with 2.5% NaOCl followed by EDTA. The teeth were assigned to 3 groups (n=10), according to the root canal sealer: Roeko Seal (Group 1), Sealer 26 (group 2) and Grossman's sealer (Group 3). Gutta-percha cold lateral condensation technique was performed in all groups. Postoperative radiographs were taken and the images were projected for evaluation of the quality of lateral canal filling. Data were submitted to statistical analysis by Kruskal Wallis test at 5% significance level. The results showed that Grossman's sealer filled a larger number of lateral canals than Roeko Seal (p<0.05) and Sealer 26 (p<0.01). It may be concluded that Roeko Seal silicone-based root canal sealer was not as effective as the Grossman's sealer for filling of simulated lateral canals. The lateral canals localized in the apical third of the root were more difficult to be filled.

scholarly journals The Effect of the Bioactive Glass and the Er:YAG Laser on the Remineralization of the Affected Dentin: A Comparative In Vitro Study

2020 ◽  
Vol 11 (2) ◽  
pp. 160-166
Author(s):  
Mohammad Javad Moghaddas ◽  
Horieh Moosavi ◽  
Sara Yaghoubirad ◽  
Nasim Chiniforush
Keyword(s):  
Bioactive Glass ◽  
In Vitro Study ◽  
Control Group ◽  
Dentinal Tubule ◽  
Glass Ionomer ◽  
Significant Difference ◽  
Post Hoc ◽  
Caries Lesions ◽  
Cavity Floor

Introduction: The purpose of this study was to compare the effect of the bioactive glass, the glass ionomer, and the Erbium YAG laser as liners on the remineralization of the affected dentin. Methods: The present study was conducted on 64 healthy extracted human molars divided into 4 groups, 1 control group and 3 experimental groups. After artificially inducing dentinal caries lesions, each of the experimental groups was applied to the cavity floor and then restored with a composite. The samples were stored after thermocycling in an incubator for two months. Finally, the hardness of the cavity floor was measured at 3 depths of 20, 50 and 100 μm by the Vickers microhardness tester. The dentin conditions underneath the liners were also evaluated with FESEM. Statistical analysis was performed by two-way ANOVA and the post-hoc Games-Howell test (P<0.05). Results: Among the groups, the lowest microhardness value was in the control group (P<0.05) except at a depth of 100 μm; therefore, there was no significant difference between the control group and the bioactive glass (P>0.05). The laser group had the highest microhardness value, which was significantly different from the control group (P<0.05). There was a significant difference between the laser and bioactive glass (P<0.05), except at a depth of 20 μm. The laser and glass ionomer had only a significant difference at a depth of 100 μm (P<0.05). The microhardness value induced by glass ionomer was higher than bioactive glass, which in no depth was significant (P>0.05). Partial dentinal tubule occlusion was observed with FESEM in each of the experimental groups as compared to the control group. Conclusion: The microhardness values were higher in all groups than in the control group. The laser might be more successful in remineralization than the other ones.

scholarly journals Comparative Evaluation of The Efficacy Of Rotary file system (Kedo-S) Vs Hand K-Files In Root Canal Preparation Of Primary Teeth Using Cone Beam Computed Tomography (CBCT) - An In Vitro Study

2019 ◽  
Vol 22 (2) ◽  
pp. 197-202
Author(s):  
Abhinaya Srinivas ◽  
LGanesh Jeevanandan ◽  
Lavanya Govindaraju ◽  
Erulappan Muthu Ganapathi Subramanian
Keyword(s):  
Computed Tomography ◽  
Cone Beam Computed Tomography ◽  
Primary Teeth ◽  
File System ◽  
In Vitro Study ◽  
Cone Beam ◽  
Root Canal Preparation ◽  
Group I ◽  
Shaping Ability

Objective: To evaluate the efficacy of rotary Kedo-S and hand K-files in shaping ability in primary canines using cone beam computed tomography. Materials and Methods: Thirty extracted primary maxillary and mandibular canines were selected. Using cone beam computed tomography the teeth were scanned before instrumentation. In Group I, the teeth were prepared using stainless steel K file up to the size of 40. In the Group II teeth, U1 size Kedo-S rotary file was used in crown down technique. The instrumented teeth were scanned again with cone beam computed tomography and the images were compared. Results: The canal taper was more conical for rotary Kedo-S files as compared to K-files, which was statistically significant. Conclusion:  Canal preparation with Rotary files resulted in more conical canals when compared to manual instrumentation in primary teeth that contributes to more uniform obturation.KeywordsCBCT; Hand K-files; Kedo-S file system; Primary teeth; Pulpectomy; Rotary instrumentation.

Force and vibration analysis in biomechanical preparation of root canals using reciprocating endodontic file system: In vitro study

2021 ◽  
pp. 095441192110442
Author(s):  
Vinod Singh Thakur ◽  
Pavan Kumar Kankar ◽  
Anand Parey ◽  
Arpit Jain ◽  
Prashant Kumar Jain
Keyword(s):  
Root Canal ◽  
Vibration Analysis ◽  
File System ◽  
In Vitro Study ◽  
Root Canal Preparation ◽  
Root Canals ◽  
Improper Use ◽  
Four Levels ◽  
Root Canal Instrumentation

The shaping and cleaning of the root canal are very important in root canal treatment. The excessive force and vibration during biomechanical preparation of the root canal may result in failure of the endodontic file. In this study, force and vibration analysis was carried out during root canal preparation. The samples of human extracted (premolar) teeth were provided by the College of Dental Science and Hospital. Endodontic instruments for reciprocating motion, such as the WaveOne Gold file system, had been used for root canal preparation. Force and vibration signals were recorded by dynamometer and accelerometer, respectively. The acquired signals were denoised using the db4 (SWT denoising 1-D) wavelet. Four levels of decomposition were carried out for each signal. The signal denoising technique was used to remove unwanted noise from the acquired signal. FESEM analysis was used to visualize the levels of severity of endodontic files during the cleaning and shaping of the root canal. In most of the cases, the failure occurred due to the improper use of the root canal instrumentation. The optimum amount of force was used to avoid the file failure and provided the proper instrumentation. The curve fitting regression model was used to find the interdependency between force and vibration.

scholarly journals Superelasticity and force plateau of nickel-titanium springs: an in vitro study

2016 ◽  
Vol 21 (3) ◽  
pp. 46-55 ◽  
Author(s):  
Camila Ivini Viana Vieira ◽  
Sergei Godeiro Fernandes Rabelo Caldas ◽  
Lídia Parsekian Martins ◽  
Renato Parsekian Martins
Keyword(s):  
Analysis Of Variance ◽  
In Vitro Study ◽  
Nickel Titanium ◽  
Vitro Study ◽  
Lack Of Information ◽  
Activation Force ◽  
Post Hoc

abstract Objective: This paper analyzed whether nickel-titanium closed coil springs (NTCCS) have a different superelastic (SE) behavior according to activation and whether their force plateau corresponds to that informed by the manufacturer. Methods: A total of 160 springs were divided into 16 subgroups according to their features and activated proportionally to the length of the extensible part (NiTi) of the spring (Y). The force values measured were analyzed to determine SE rates and force plateaus, which were mathematically calculated. These plateaus were compared to those informed by the manufacturer. Analysis of variance was accomplished followed by Tukey post-hoc test to detect and analyze differences between groups. Results: All subgroups were SE at the activation of 400% of Y length, except for: subgroups 4B and 3A, which were SE at 300%; subgroups 4E and 4G, which were SE at 500%; and subgroup 3C, which was SE at 600%. Subgroup 3B did not show a SE behavior. Force plateaus depended on activation and, in some subgroups and some activations, were similar to the force informed. Conclusions: Most of the springs showed SE behavior at 400% of activation. Force plateaus are difficult to compare due to lack of information provided by manufacturers.

scholarly journals Influence of calcium hydroxide points on the quality of intracanal dressing filling

2006 ◽  
Vol 14 (3) ◽  
pp. 219-223 ◽  
Author(s):  
Nicole de Mello Rahde ◽  
José Antonio Poli Figueiredo ◽  
Elias Pandonor Motcy Oliveira
Keyword(s):  
Calcium Hydroxide ◽  
Root Canal Filling ◽  
Human Teeth ◽  
Significance Level ◽  
Root Canals ◽  
Gutta Percha ◽  
Group 2 ◽  
Post Hoc

PURPOSE: The aim of this study was to evaluate, in vitro, the quality of calcium hydroxide [Ca(OH)2] paste filling (Ultracal, Ultradent) associated or not with Ca(OH)2-containing gutta-percha points (Calcium Hydroxide Plus PointsTM, Roeko) in curved root canals. MATERIAL AND METHODS: One hundred and twenty roots of extracted human teeth, randomly divided into three curvature ranges (mild - 0 to 14º; moderate - 15º to 29º; severe - >30º) were used. After chemomechanical preparation, the roots were assigned to 4 groups (n=30), according to the technique of intracanal dressing placement: group 1 - Ca(OH)2 paste was applied with a lentulo spiral; group 2 - Ca(OH)2 paste was applied with a lentulo spiral and a Ca(OH)2 point was inserted into the canal; group 3 - Ca(OH)2 paste was applied with a NavitipTM tip (supplied with Ultracal system); group 4 - Ca(OH)2 paste was applied with a NavitipTM tip and a Ca(OH)2 point was inserted into the canal. The roots were cleared and the quality of apical third filling was assessed by a calibrated experienced examiner. The specimens were examined under stereomicroscopy and scored 1 to 4 (i.e., from inadequate to complete root canal filling). The results were analyzed statistically by ANOVA and Duncan's post hoc test at 5% significance level. RESULTS: There were no statistically significant differences (p>0.05) among the curvature degrees in groups 1, 3 and 4. Severely curved roots in group 2 presented bordering significance (p=0.05). The groups that associated the use of Ca(OH)2 paste and points (2 and 4) showed better apical filling than the other groups, but this difference was statistically significant (p<0.001) only for roots with severe curvature. CONCLUSION: According to the results of this study, the curvature degree did not influence the quality of filling. The techniques that used Ca(OH)2-containing gutta-percha points yielded better filling of the apical third in roots with severe curvature.

Sign in / Sign up

Export Citation Format

Share Document