scholarly journals RESEARCH OF FUNCTIONAL AND TECHNOLOGICAL PARAMETERS OF HIGH PRESSURE PROCESSED MEAT

2020 ◽  
Vol 5 (1) ◽  
pp. 17-21 ◽  
Author(s):  
Irina A. Prokopenko
Keyword(s):  
High Pressure ◽  
Hydrostatic Pressure ◽  
High Hydrostatic Pressure ◽  
Broiler Chickens ◽  
Binding Capacity ◽  
High Pressure Processing ◽  
Raw Material ◽  
Poultry Meat ◽  
Processed Meat ◽  
Water Binding

High hydrostatic pressure (ННP) technology has been widely used in the developed countries food industry for production and preservation of raw materials and products. In our country the possibility of a new processing method is being now tested only on experimental installations. For research we selected a pressure range from 200 to 700 MPa, the exposure duration at room temperature was 20 minutes. This article presents the results of the high pressure impact on pH, water-binding capacity of broiler chickens meat, moreover comparative assessment of range of losses that occur during heat treatment and high hydrostatic pressure were analyzed. The dynamics of change of the ultimate sheer stress depending on the ННP value is shown. It is established that the new technology in the selected range does not significantly affect the pH value. However the value of water-binding capacity increases along with increasing of pressure: during processing by 200 MPa it increases by 10.5%, within the range of 200–300 MPa it increases by additional 3.0%, and within the range from 300 to 700 MPa the value increased only slightly. Significant changes were observed in the determination of losses while technological processing of meat. Thus the losses during conventional boiling of broiler chickens fillets were 28.5% higher than during high-pressure processing. It is noted that within the range of 200–700 MPa this parameter increases by only 4.8%. As the pressure increased, the texture of the meat becomes denser, as evidenced by the results of the study of the structural and mechanical properties of the raw material. Based on the results of the implemented work, it is recommended to use ННP technology within the range of 600–700 MPa, processing time of 20 min at 20±1 ºС for production of poultry meat products.

Effects of high hydrostatic pressure on Campylobacter jejuni in poultry meat

2015 ◽  
Vol 18 (2) ◽  
pp. 261-266 ◽  
Author(s):  
A. Jackowska-Tracz ◽  
M. Tracz
Keyword(s):  
High Pressure ◽  
Hydrostatic Pressure ◽  
Campylobacter Jejuni ◽  
High Hydrostatic Pressure ◽  
High Pressure Processing ◽  
Poultry Meat ◽  
Chicken Breast ◽  
Regression Equations ◽  
Dependent Manner ◽  
Piston Cylinder

Abstract Campylobacter jejuni inactivation by high pressure processing (HPP) in poultry meat (chicken breast) was investigated. The pressure was created by high hydrostatic pressure piston-cylinder food processor. Contaminated with C. jejuni (108 CFU g−1) samples of ground poultry meat were hermetically sealed in a polyamide-polyethylene bags and exposed to HPP for 9 different combinations of pressure (200 MPa, 300 MPa and 400 MPa) and time (5 min, 10 min and 15 min). Quantitative bacteriological analysis was carried out in order to determine the number of surviving C. jejuni cells. The obtained results showed that C. jejuni is relatively sensitive to high pressure treatment as compared to other food-borne pathogens. The loss of C. jejuni viability increased in a dose- and time-dependent manner. On the basis of the results, D-values were calculated. For reduction C. jejuni in poultry meat by 6 log units (6D-values), considered as sufficient for consumer protection, the application of 300 MPa for 8.73 min, or 400 MPa for 4.37 min is needed. The linear regression equations, which has been calculated on the basis of this study, allows to determine the degree of C. jejuni reduction in poultry meat for any selected duration of pressurization in a given pressure range.

Effect of High Hydrostatic Pressure on Salmonella Inoculated into Creamy Peanut Butter with Modified Composition

2014 ◽  
Vol 77 (10) ◽  
pp. 1664-1668 ◽  
Author(s):  
TANYA D'SOUZA ◽  
MUKUND KARWE ◽  
DONALD W. SCHAFFNER
Keyword(s):  
High Pressure ◽  
Hydrostatic Pressure ◽  
Water Activity ◽  
High Hydrostatic Pressure ◽  
Peanut Butter ◽  
High Pressure Processing ◽  
Peanut Oil ◽  
Peanut Flour ◽  
Log Reduction ◽  
High Hydrostatic Pressure Processing

Peanut butter has been associated with several large foodborne salmonellosis outbreaks. This research investigates the potential of high hydrostatic pressure processing (HPP) for inactivation of Salmonella in peanut butter of modified composition, both by modifying its water activity as well by the addition of various amounts of nisin. A cocktail of six Salmonella strains associated with peanut butter and nut-related outbreaks was used for all experiments. Different volumes of sterile distilled water were added to peanut butter to increase water activity, and different volumes of peanut oil were added to decrease water activity. Inactivation in 12% fat, light roast, partially defatted peanut flour, and peanut oil was also quantified. Nisaplin was incorporated into peanut butter at four concentrations corresponding to 2.5, 5.0, 12.5, and 25.0 ppm of pure nisin. All samples were subjected to 600 MPa for 18 min. A steady and statistically significant increase in log reduction was seen as added moisture was increased from 50 to 90%. The color of all peanut butter samples containing added moisture contents darkened after high pressure processing. The addition of peanut oil to further lower the water activity of peanut butter further reduced the effectiveness of HPP. Just over a 1-log reduction was obtained in peanut flour, while inactivation to below detection limits (2 log CFU/g) was observed in peanut oil. Nisin alone without HPP had no effect. Recovery of Salmonella after a combined nisin and HPP treatment did show increased log reduction with longer storage times. The maximum log reduction of Salmonella achieved was 1.7 log CFU/g, which was comparable to that achieved by noncycling pressure treatment alone. High pressure processing alone or with other formulation modification, including added nisin, is not a suitable technology to manage the microbiological safety of Salmonella-contaminated peanut butter.

scholarly journals Evaluating the Anti-Inflammatory and Antioxidant Effects of Broccoli Treated with High Hydrostatic Pressure in Cell Models

Foods ◽  
2021 ◽  
Vol 10 (1) ◽  
pp. 167
Author(s):  
Yi-Yuan Ke ◽  
Yuan-Tay Shyu ◽  
Sz-Jie Wu
Keyword(s):  
High Pressure ◽  
Hydrostatic Pressure ◽  
High Hydrostatic Pressure ◽  
High Pressures ◽  
High Pressure Processing ◽  
Total Phenolic ◽  
Anti Inflammatory ◽  
Functional Components ◽  
Antioxidant Effects ◽  
Myrosinase Activity

Isothiocyanates (ITCs) are important functional components of cruciferous vegetables. The principal isothiocyanate molecule in broccoli is sulforaphane (SFN), followed by erucin (ERN). They are sensitive to changes in temperature, especially high temperature environments where they are prone to degradation. The present study investigates the effects of high hydrostatic pressure on isothiocyanate content, myrosinase activity, and other functional components of broccoli, and evaluates its anti-inflammatory and antioxidant effects. Broccoli samples were treated with different pressures and for varying treatment times; 15 min at 400 MPa generated the highest amounts of isothiocyanates. The content of flavonoids and vitamin C were not affected by the high-pressure processing strategy, whereas total phenolic content (TPC) exhibited an increasing tendency with increasing pressure, indicating that high-pressure processing effectively prevents the loss of the heat-sensitive components and enhances the nutritional content. The activity of myrosinase (MYR) increased after high-pressure processing, indicating that the increase in isothiocyanate content is related to the stimulation of myrosinase activity by high-pressure processing. In other key enzymes, the ascorbate peroxidase (APX) activity was unaffected by high pressure, whereas peroxidase (POD) and polyphenol oxidase (PPO) activity exhibited a 1.54-fold increase after high-pressure processing, indicating that high pressures can effectively destroy oxidases and maintain food quality. With regards to efficacy evaluation, NO production was inhibited and the expression levels of inducible nitric oxide synthase (iNOS) and Cyclooxygenase-2 (COX-2) were decreased in broccoli treated with high pressures, whereas the cell viability remained unaffected. The efficacy was more significant when the concentration of SFN was 60 mg·mL−1. In addition, at 10 mg·mL−1 SFN, the reduced/oxidized glutathione (GSH/GSSG) ratio in inflammatory macrophages increased from 5.99 to 9.41. In conclusion, high-pressure processing can increase the isothiocyanate content in broccoli, and has anti-inflammatory and anti-oxidant effects in cell-based evaluation strategies, providing a potential treatment strategy for raw materials or additives used in healthy foods.

Effect of High Hydrostatic Pressure and Pressure Cycling on a Pathogenic Salmonella enterica Serovar Cocktail Inoculated into Creamy Peanut Butter

2012 ◽  
Vol 75 (1) ◽  
pp. 169-173 ◽  
Author(s):  
TANYA D'SOUZA ◽  
MUKUND KARWE ◽  
DONALD W. SCHAFFNER
Keyword(s):  
High Pressure ◽  
Hydrostatic Pressure ◽  
High Hydrostatic Pressure ◽  
Salmonella Enterica ◽  
Salmonella Enteritidis ◽  
Peanut Butter ◽  
High Pressure Processing ◽  
High Moisture ◽  
Pressure Cycling ◽  
High Hydrostatic Pressure Processing

The ability of Salmonella enterica serovars to survive in high fat content, low water activity foods like peanut butter has been demonstrated by large foodborne illness outbreaks in recent years. This study investigates the potential of high hydrostatic pressure processing, including pressure cycling, to inactivate Salmonella inoculated into creamy peanut butter. A cocktail of pathogenic strains of Salmonella Enteritidis PT30, Salmonella Tennessee, Salmonella Oranienburg, Salmonella Anatum, Salmonella Enteritidis PT 9c, and Salmonella Montevideo obtained from peanut butter– and nut-related outbreaks was inoculated (106 to 107 CFU/g) into creamy peanut butter and high pressure processed under five different sets of conditions, which varied from 400 to 600 MPa and from 4 to 18 min. The log CFU reductions achieved varied from 1.6 to 1.9. Control experiments in which Salmonella was inoculated (109 CFU/g) into 0.1% peptone buffer and high pressure processed at 600 MPa for 18 min showed inactivation to below the detection limit of 100 CFU/g, confirming that high pressure processing is effective at destroying Salmonella in high-moisture environments. Pressure cycling under three sets of conditions consisting of pressures from 400 to 600 MPa, 3 to 10 pressure cycles, and hold times of 6 min for each cycle showed reductions similar to those seen in noncycling experiments. The results of our experiments suggest that the peanut butter food matrix facilitates the survival of Salmonella when exposed to high hydrostatic pressure processing.

scholarly journals High Pressure Processing of Meat and Meat Products: Application Aspects and Prospects of Use

2020 ◽  
Vol 222 ◽  
pp. 03011
Author(s):  
Alexey Volkov ◽  
Lyudmila Donskova ◽  
Victoria Kotkova
Keyword(s):  
High Pressure ◽  
Hydrostatic Pressure ◽  
High Hydrostatic Pressure ◽  
Meat Products ◽  
High Pressure Processing ◽  
Research Database ◽  
Technical Parameters ◽  
High Hydrostatic Pressure Processing ◽  
Minced Meat ◽  
The Impact

The authors consider the technology of processing meat and meat products using high hydrostatic pressure (HHP). Based on the results of research carried out in different countries in different years and the results of our own research, the effectiveness of the use of high pressure and its role in the control and stabilization of the microflora of finished meat products and increasing their shelf life is shown. Research data indicating the possibility of using high pressure in the processing of minced meat and beef trimmings are presented. Differences in the technical parameters of the HHP technology have been established, the results show the possibility of applying a pressure value of 250 MPa, in contrast to 300-600 MPa used in research by foreign scientists. The results obtained on the protein component of cooked sausage products exposed to high pressure are of applied research interest and expand the research database. The authors consider the continuation of research in determining the optimal parameters of this technology, identifying the impact on the consumer properties of meat products, and developing organizational and methodological measures to increase the commercialization of high hydrostatic pressure processing to be promising areas.

Predictive Model for Inactivation of Campylobacter spp. by Heat and High Hydrostatic Pressure

2007 ◽  
Vol 70 (9) ◽  
pp. 2023-2029 ◽  
Author(s):  
SEHAM LORI ◽  
ROMAN BUCKOW ◽  
DIETRICH KNORR ◽  
VOLKER HEINZ ◽  
ANSELM LEHMACHER
Keyword(s):  
High Pressure ◽  
Hydrostatic Pressure ◽  
High Hydrostatic Pressure ◽  
Poultry Meat ◽  
Inactivation Kinetics ◽  
Order Kinetic ◽  
Pressure Treatment ◽  
Short Term ◽  
Short Term Treatment ◽  
High Pressure Treatment

Campylobacter represents one of the leading causes of foodborne enteritis. Poultry and its products frequently transmit the pathogen. The objective of the present study was to model predictively the short-term inactivation of Campylobacter in a ready-to-eat poultry product to develop an economic high-pressure treatment. We inactivated baroresistant strains of Campylobacter jejuni and Campylobacter coli, grown to stationary phase on nutrient agar and inoculated in poultry meat slurry, by heat and high hydrostatic pressure. Incubation at ambient pressure at 70°C for 1 min and at 450 MPa at 15°C for 30 s inactivated more than 6 log CFU of this foodborne pathogen per ml of poultry meat slurry. Thermal and pressure inactivation kinetics of C. coli and C. jejuni in poultry meat slurry were accurately described by a first-order kinetic model. A mathematical model was developed from 10 to 65°C and from ambient to 500 MPa that predicts the reduction in numbers of Campylobacter in response to the combination of temperature, pressure, and treatment time. We suggest the high-pressure treatment of foods to avoid health risks caused by Campylobacter. The nonthermal short-term treatment of the examined food model system represents a successful step to an economic high-pressure procedure.

Application and possible benefits of high hydrostatic pressure or high-pressure homogenization on beer processing: A review

2017 ◽  
Vol 23 (7) ◽  
pp. 561-581 ◽  
Author(s):  
Lígia MR Santos ◽  
Fabiano A Oliveira ◽  
Elisa HR Ferreira ◽  
Amauri Rosenthal
Keyword(s):  
High Pressure ◽  
Hydrostatic Pressure ◽  
High Hydrostatic Pressure ◽  
Sensory Quality ◽  
Alcoholic Beverage ◽  
Protein Structures ◽  
High Pressure Processing ◽  
Sensory Characteristics ◽  
High Pressure Homogenization ◽  
Barley Malt

Beer is the most consumed beverage in the world, especially in countries such as USA, China and Brazil.It is an alcoholic beverage made from malted cereals, and the barley malt is the main ingredient, added with water, hops and yeast. High-pressure processing is a non-traditional method to preserve food and beverages. This technology has become more interesting compared to heat pasteurization, due to the minimal changes it brings to the original nutritional and sensory characteristics of the product, and it comprises two processes: high hydrostatic pressure, which is the most industrially used process, and high-pressure homogenization. The use of high pressure almost does not affect the molecules that are responsible for the aroma and taste, pigments and vitamins compared to the conventional thermal processes. Thus, the products processed by high-pressure processing have similar characteristics compared to fresh products, including beer. The aim of this paper was to review what has been investigated about beer processing using this technology regarding the effects on physicochemical, microbiology and sensory characteristics and related issues. It is organized by processing steps, since high pressure can be applied to malting, mashing, boiling, filtration and pasteurization. Therefore, the beer processed with high-pressure processing may have an extended shelf-life because this process can inactivate beer spoilage microorganisms and result in a superior sensory quality related to freshness and preservation of flavors as it does to juices that are already commercialized. However, beyond this application, high-pressure processing can modify protein structures, such as enzymes that are present in the malt, like α- and β-amylases. This process can activate enzymes to promote, for example, saccharification, or instead inactivate at the end of mashing, depending on the pressure the product is submitted, besides being capable of isomerizing hops to raise beer bitterness. As a consequence, the process may reduce steam demand and residue generation. Therefore, the use of high-pressure processing can potentially replace or be combined with heat processes usually applied to beer, thus bringing benefits to the sensory quality of the product and to the environment.

Impact of high-pressure homogenization on the microstructure and rheological properties of citrus fiber

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Dianbin Su ◽  
Xin-Di Zhu ◽  
Yong Wang ◽  
Dong Li ◽  
Li-Jun Wang
Keyword(s):  
Particle Size ◽  
High Pressure ◽  
Rheological Properties ◽  
Binding Capacity ◽  
Loss Modulus ◽  
High Pressure Homogenization ◽  
Carreau Model ◽  
Hydration Properties ◽  
Water Binding ◽  
Water Holding

Abstract Citrus fiber dispersion with different concentrations (5–25 g/kg) was treated by high-pressure homogenization (90 and 160 MPa) for two cycles. The particle size distribution, hydration properties of powders, morphology and rheological measurements were carried out to study the microstructure and rheological properties changes by high-pressure homogenization (HPH). In conclusion, the HPH can reduce the particle size of fiber, improve the water holding capacity and water binding capacity. Furthermore, fiber shape can be modified from globular cluster to flake-like slices, and tiny pores can be formed on the surface of citrus fiber. The apparent viscosity, storage modulus and loss modulus were increased by HPH whereas the activation energy was reduced. The Hershcel–Bulkley model, Carreau model and Power Law mode were selected to evaluate the rheological properties.

Sign in / Sign up

Export Citation Format

Share Document