Parametric Influence Study for Laser Cutting on Acrylic

2021 ◽  
Author(s):  
Sandeep S. Wangikar ◽  
Manthan M Dixit ◽  
Saurabh G Wadekar ◽  
Harshal R Nagtilak ◽  
Nitin D Hingmire ◽  
...  
Keyword(s):  
Co2 Laser ◽  
Process Parameters ◽  
Laser Power ◽  
Laser Cutting ◽  
Scanning Speed ◽  
Laser Machining ◽  
Response Measure ◽  
Machining Processes ◽  
The One ◽  
Day By Day

Laser has been employed for producing the complex specimens very efficiently and magnificently. The use of acrylic components is becoming prevalent day by day. Hence it is required to study the various machining techniques for engraving or cutting of acrylic material. The one of the non-traditional machining processes which can be employed efficiently for machining of acrylic is CO2 laser machining. The parametric study of acrylic materials by using CO2 laser machining is discussed in this paper. The scanning speed and the laser power were considered as process parameters and the influence of these parameters is studied on the depth as response measure. The engraving depth is observed to be increasing with increase in power and noted to be decreasing with increase in the scanning speed.

EXPERIMENTAL STUDY ON THE CO2 LASER CUTTING OF NOVEL POLYAMIDE 6/FLUOROELASTOMER THERMOPLASTIC ELASTOMERIC BLENDS

2015 ◽  
Vol 88 (1) ◽  
pp. 125-137 ◽  
Author(s):  
Shib Shankar Banerjee ◽  
Anil K. Bhowmick
Keyword(s):  
Low Power ◽  
Co2 Laser ◽  
Process Parameters ◽  
Laser Power ◽  
Laser Cutting ◽  
Manufacturing Industry ◽  
Cutting Speed ◽  
Polyamide 6 ◽  
Thermoplastic Elastomers ◽  
Dynamic Vulcanization

ABSTRACT The application of the low-power CO2 laser-cutting process to fluoroelastomer (FKM), polyamide 6 (PA6), PA6/FKM thermoplastic elastomers (TPEs), and their thermoplastic vulcanizate (TPV) is reported. The main laser process parameters studied were laser power, cutting speed, and material thickness. The value of the top and bottom widths of the slit that were formed during laser cutting (kerf width), melted transverse area, and melted volume per unit time were measured and analyzed. Interestingly, TPE showed a smaller melted area and melted volume per unit time when compared with those values with PA6. Dynamic vulcanization further decreased these values. For example, the melted areas of PA6 and TPE were 510 × 10−3 mm2 and 305 × 10−3 mm2, respectively, which reduced to 238 × 10−3 mm2 for TPV at 40 W laser power. FKM showed the lowest value (melted area of 180 × 10−3 mm2). In addition, the output quality of the cut surface was examined by measuring the root mean square (RMS) roughness of the cut edges and heat-affected zone (HAZ). The obtained results indicated that the dimension of the HAZ and RMS roughness largely decreased in TPE when compared with PA6. For example, the HAZ of PA6 was 700 μm, which decreased to 230 μm for TPE at 40 W laser power. On the other hand, HAZ was nonexistent for FKM. Infrared spectroscopic analysis showed that there was no structural change of TPE or pristine polymers after applying the low-power CO2 laser on the surface of materials. CO2 laser cutting will be a new technique in this industry, and this analysis will assist the manufacturing industry to choose a suitable laser system with exhaustive information of process parameters for cutting or machining of rubber, TPEs, and TPVs.

scholarly journals Fabrication of Micro-channels using CO2 LASER Machining & Soft Lithography for Lab-on-Chip Applications

2021 ◽  
Author(s):  
Avinash K Parkhe ◽  
Amol Dhondiba Sul ◽  
Prathmesh Ramesh Kirgat ◽  
Atharv Santosh Joshi ◽  
Prakash Bhimrao Ghadage ◽  
...  
Keyword(s):  
Co2 Laser ◽  
Laser Power ◽  
Soft Lithography ◽  
Laser Scanning ◽  
Scanning Speed ◽  
Laser Machining ◽  
Lab On Chip ◽  
Micro Channels ◽  
Acrylic Sheet ◽  
On Chip

Microchannels are one of the most significant parts for the Lab-on-Chip applications. The microchannels fabrication is a crucial task. The Soft Lithography is one of the most favored methods of microchannel fabrication. The use of CO2 LASER machining for microchannel fabrication using Acrylic sheet is studied in this paper. The experimentation is carried out to see the effect of LASER scanning speed and laser power on the depth of the microchannel mold. It has observed that the channel depth is increasing linearly with increasing LASER power and decreasing with increase in speed. The straight microchannel configuration with Y shaped inlet having circular & elliptical obstacles has been fabricated using CO2 laser machining on acrylic sheet. Also, the fabricated molds are used to prepare the further microchannel molds using the Soft Lithography technique and then the microchannels prepared from Soft Lithography are used as a mold for the lab-on-chip applications like check the mixing length & mixing phenomenon etc.

Research on Warpage of Polystyrene in Selective Laser Sintering

2010 ◽  
Vol 43 ◽  
pp. 578-582 ◽  
Author(s):  
C.Y. Wang ◽  
Q. Dong ◽  
X.X. Shen
Keyword(s):  
Layer Thickness ◽  
Process Parameters ◽  
Laser Power ◽  
Selective Laser Sintering ◽  
Scanning Speed ◽  
Laser Sintering ◽  
Main Process ◽  
Influence Of Process Parameters ◽  
Temperature Changes ◽  
Hatch Spacing

Warpage is a crucial factor to accuracy of sintering part in selective laser sintering (SLS) process. In this paper, The influence of process parameters on warpage when sintering polystyrene(PS) materials in SLS are investigated. The laser power, scanning speed, hatch spacing, layer thickness as well as temperature of powder are considered as the main process parameters. The results showed that warpage increases with the increase of hatch space. Contary to it, warpage decreases with the increase of laser power. Warpage decreases with the increase of layer thickness between 0.16~0.18mm and changes little with increase of the thickness. Warpage increases along with the increase of scanning speed but decreases when the speed is over about 2000mm/s. When the temperature changes between 82°C-86°C, warpage decreases little with the increase of temperature. But further increase of temperature leads to warpage decreasing sharply when the temperature changes between 86°C-90°C.

Effect of CO2 laser cutting process parameters on edge quality and operating cost of AISI316L

2012 ◽  
Vol 44 (4) ◽  
pp. 1068-1082 ◽  
Author(s):  
H.A. Eltawahni ◽  
M. Hagino ◽  
K.Y. Benyounis ◽  
T. Inoue ◽  
A.G. Olabi
Keyword(s):  
Co2 Laser ◽  
Process Parameters ◽  
Laser Cutting ◽  
Operating Cost ◽  
Cutting Process ◽  
Edge Quality

EXPERIMENTAL EVALUATION OF CO2 LASER CUTTING QUALITY OF UHSS USING OXYGEN AS AN ASSISTED GAS

2016 ◽  
Vol 78 (7) ◽  
Author(s):  
Abdul Fattah Mohamad Tahir ◽  
Ahmad Razelan Rashid
Keyword(s):  
Co2 Laser ◽  
High Strength Steel ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
High Strength ◽  
Gas Pressure ◽  
Kerf Width ◽  
Boron Steel ◽  
Major Factors

Development of new material known as Ultra High Strength Steel (UHSS) able to improve the vehicle mass thus reflecting better fuel consumption. Transformation into high strength steel has been a significant drawback in trimming the UHSS into its final shape thus laser cutting process appeared to be the solution. This study emphasizes the relationship between Carbon Dioxide (CO2) laser cutting input parameters on 22MnB5 boron steel focusing on the kerf width formation and Heat Affected Zone (HAZ). Experimental research with variation of laser power, cutting speed and assisted gas pressure were executed to evaluate the responses. Metrological and metallographic evaluation of the responses were made on the outputs that are the kerf width formation and HAZ.  Positive correlation for power and negative interaction for cutting speed were found as the major factors on formation of the kerf. For the HAZ formation, thicker HAZ were formed as bigger laser power were applied to the material. Cutting speed and gas pressure does not greatly influence the HAZ formation for 22MnB5 boron steel.

scholarly journals Numerical Simulation of Moving Heat Flux during Selective Laser Melting of AlSi25 Alloy Powder

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 877
Author(s):  
Cong Ma ◽  
Xianshun Wei ◽  
Biao Yan ◽  
Pengfei Yan
Keyword(s):  
Numerical Simulation ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Molten Pool ◽  
Laser Power ◽  
Scanning Speed ◽  
Powder Layer ◽  
Maximum Temperature ◽  
Three Dimensional Model ◽  
Laser Melting

A single-layer three-dimensional model was created to simulate multi-channel scanning of AlSi25 powder in selective laser melting (SLM) by the finite element method. Thermal behaviors of laser power and scanning speed in the procedure of SLM AlSi25 powder were studied. With the increase of laser power, the maximum temperature, size and cooling rate of the molten pool increase, while the scanning speed decreases. For an expected SLM process, a perfect molten pool can be generated using process parameters of laser power of 180 W and a scanning speed of 200 mm/s. The pool is greater than the width of the scanning interval, the depth of the molten pool is close to scan powder layer thickness, the temperature of the molten pool is higher than the melting point temperature of the powder and the parameters of the width and depth are the highest. To confirm the accuracy of the simulation results of forecasting excellent process parameters, the SLM experiment of forming AlSi25 powder was carried out. The surface morphology of the printed sample is intact without holes and defects, and a satisfactory metallurgical bond between adjacent scanning channels and adjacent scanning layers was achieved. Therefore, the development of numerical simulation in this paper provides an effective method to obtain the best process parameters, which can be used as a choice to further improve SLM process parameters. In the future, metallographic technology can also be implemented to obtain the width-to-depth ratio of the SLM sample molten pool, enhancing the connection between experiment and theory.

scholarly journals Preliminary Testing to Determine the Best Process Parameters for Polymer Laser Sintering of a New Polypropylene Polymeric Material

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Fredrick M. Mwania ◽  
Maina Maringa ◽  
Jakobus. G. van der Walt
Keyword(s):  
Mechanical Properties ◽  
Polymeric Material ◽  
Process Parameters ◽  
Laser Power ◽  
Scanning Speed ◽  
Laser Sintering ◽  
Process Conditions ◽  
Preliminary Testing ◽  
Chamber Temperature ◽  
Suitable Process

Polymer laser sintering is an elaborate additive manufacturing technique because it is subject to process parameters and material properties. In this regard, each polymeric material necessitates a different set of process conditions. To this end, testing was done to determine the most suitable process parameters for a new commercially available polymer (Laser PP CP 60), from Diamond Plastics GmbH. It was established that the material requires slightly different settings from those provided by the supplier for the values for the removal chamber temperature, building chamber temperatures, and laser power to achieve the best mechanical properties (ultimate tensile strength). The preliminary testing indicates that the process parameters that yielded the best mechanical properties for the laser PP CP 60 powder were 125°C, 125°C, 0.15 mm, 250 μm, 4500 mm/s, 34.7 W, 1500 mm/s, and 21.3 W for the removal chamber temperature, building chamber temperature layer thickness, hatch distance, scanning speed fill, laser power fill, scanning speed contour, and laser power contour, respectively.

scholarly journals Multi-objective numerical simulation of geometrical characteristics of laser cladding of cobalt-based alloy based on response surface methodology

2020 ◽  
pp. 002029402094495
Author(s):  
Lu-jun Cui ◽  
Meng Zhang ◽  
Shi-Rui Guo ◽  
Yan-Long Cao ◽  
Wen-Han Zeng ◽  
...  
Keyword(s):  
Prediction Model ◽  
Response Surface ◽  
Laser Cladding ◽  
Process Parameters ◽  
Laser Power ◽  
Influence Factors ◽  
Scanning Speed ◽  
Laser Cladding Remanufacturing ◽  
Main Influence

The objectives of this study are to optimize the key process parameters of laser cladding remanufacturing parts, improve the sealing quality of the hemispherical valve and prolong and improve its service life and reliability. A high-power fiber-coupled semiconductor laser was used to fabricate a single Co-based alloy cladding layer on the pump valve material ZG45 plate. The key process parameters of laser power, scanning speed and powder feeding rate in the process of laser remanufacturing are taken as optimization variables, and the coating width, coating height, coating depth, aspect ratio and dilution rate are taken as response indexes. Based on the response surface analysis method, the central compound experiment is designed using Design-Expert software. The variance analysis of the experimental results is performed, and the regression prediction model of the process parameters relative to the corresponding index is established. Through analysis of the established perturbation diagram and three-dimensional response surface, it is concluded that the main influence factors of melting width and penetration depth are laser power and positive effect, and the main influence factors of melting height are scanning speed and negative effect. The average error of each regression prediction model is lower than 10%. The above research work has important guiding significance for optimizing the process parameters and improving the cladding quality of cobalt-based alloy on ZG45.

Sign in / Sign up

Export Citation Format

Share Document