scholarly journals EFFECT OF DISPERSING LITHIUM GREASE BY CLAY PARTICLES

2021 ◽  
Vol 18 (4) ◽  
pp. 55-65
Keyword(s):  
Lithium Grease ◽  
Clay Particles

Application of a Simple Cold Stub to the Direct Observation of Frozen Hydrated Sand

1973 ◽  
Vol 31 ◽  
pp. 212-213
Author(s):  
John M. Wehrung ◽  
Richard J. Harniman
Keyword(s):  
United States ◽  
Surface Water ◽  
Direct Observation ◽  
Controlled Study ◽  
Clay Particles ◽  
Organic Debris ◽  
Rock Formations ◽  
Water Tables ◽  
Permeable Rock ◽  
Natural Means

Water tables in aquifer regions of the southwest United States are dropping off at a rate which is greater than can be replaced by natural means. It is estimated that by 1985 wells will run dry in this region unless adequate artificial recharging can be accomplished. Recharging with surface water is limited by the plugging of permeable rock formations underground by clay particles and organic debris.A controlled study was initiated in which sand grains were used as the rock formation and water with known clay concentrations as the recharge media. The plugging mechanism was investigated by direct observation in the SEM of frozen hydrated sand samples from selected depths.

Formulation and Evaluation of Chitosan-Polyaniline Nanocomposites for Controlled Release of Anticancer Drug Doxorubicin

2018 ◽  
Vol 8 (2) ◽  
Author(s):  
Dillip Kumar Behera ◽  
Kampal Mishra ◽  
Padmolochan Nayak
Keyword(s):  
Tensile Strength ◽  
Drug Release ◽  
Nanocomposite Films ◽  
Casting Method ◽  
Sustained Drug Release ◽  
In Vitro Drug Release ◽  
Clay Particles ◽  
Solution Casting Method ◽  
Nanoclay Content

In this present work, chitosan (CS) crosslink with polyaniline (PANI) with montmorilonite (MMT) called as (CSPANI/MMT) and CS crosslink with PANI without MMT called as (CS-PANI) were prepared by employing the solution casting method. Further the formation of nanocomposites CS-PANI/MMT and CS-PANI were investigated using XRD, FTIR, SEM and tensile strength. Water uptake and swelling ratio of the CS-PANI and CS-PANI/MMT were found to decrease with increase in concentration of clay. Mechanical properties of the CS-PANI and CS-PANI/MMT were assessed in terms of tensile strength and extensibility using texture analyzer. Increase in tensile strength and reduction in extensibility was reported with increase in the nanoclay content. In vitro drug release study on CS-PANI and CS-PANI/MMT indicated pronounced sustained release of doxorubicin by the incorporation of clay particles in the CS polymer matrix. Overall CSPANI/MMT nanocomposite films exhibited improved mechanical and sustained drug release properties than CS-PANI.

Depressed filtration ripening enhances removal of Cryptosporidium parvum

2002 ◽  
Vol 2 (3) ◽  
pp. 159-168 ◽  
Author(s):  
V. Gitis ◽  
R.C. Haught ◽  
R.M. Clark ◽  
E. Radha Krishnan
Keyword(s):  
Surface Water ◽  
Cryptosporidium Parvum ◽  
Pilot Scale ◽  
Kaolin Clay ◽  
Clay Particles ◽  
Physico Chemical ◽  
Cryptosporidium Parvum Oocysts ◽  
Granular Filtration ◽  
Electrostatic Adhesion ◽  
Innovative Concept

Pilot-scale experiments were conducted to investigate removal of Cryptosporidium parvum by contact granular filtration. The research demonstrated enhanced removal of Cryptosporidium parvum in the presence of kaolin particles. This is believed to be due electrostatic adhesion of Cryptosporidium parvum oocysts to the kaolin clay particles. The elementary physico-chemical interactions between filter granules and suspension particles will be discussed. This innovative concept was successfully implemented to reduce the ripening sequence of subsequent filtration experimental test runs by the addition of large surface area particles to slurry of kaolin and Cryptosporidium parvum in surface water.

Harnessing clay nano-particles for stem-cell driven tissue regeneration, EPSRC

Impact ◽  
2018 ◽  
Vol 2018 (3) ◽  
pp. 26-28
Author(s):  
Jonathan Dawson ◽  
Richard Oreffo
Keyword(s):  
Stem Cells ◽  
Stem Cell ◽  
Blood Vessels ◽  
The Body ◽  
Biological Molecules ◽  
Nano Particles ◽  
Clay Particles ◽  
Clay Nanoparticles ◽  
Signalling Molecules ◽  
The Right

Gels made from clay could provide an environment able to stimulate stem-cells due to their ability to bind biological molecules. That molecules stick to clay has been known by scientists since the 1960s. Doctors observed that absorption into the blood stream of certain drugs was severely reduced when patients were also receiving clay-based antacid or anti-diarrhoeal treatments. This curious phenomenon was realized to be due to binding of the drugs by clay particles. This interaction is now routinely harnessed in the design of tablets to carefully control the release and action of a drug. Dr Dawson now proposes to use this property of clay to create micro-environments that could stimulate stem cells to regenerate damaged tissues such as bone, cartilage or skin. The rich electrostatic properties of nano (1 millionth of a millimetre) -scale clay particles which mediate these interactions could allow two hurdles facing the development of stem-cell based regenerative therapies to be overcome simultaneously. The first challenge - to deliver and hold stem cells at the right location in the body - is met by the ability of clays to self-organise into gels via the electrostatic interactions of the particles with each other. Cells mixed with a low concentration (less than 4%) of clay particles can be injected into the body and held in the right place by the gel, eliminating, in many situations, the need for surgery. Clay particles can also interact with large structural molecules (polymers) which are frequently used in the development of materials (or 'scaffolds'), designed to host stem cells. These interactions can greatly improve the strength of such structures and could be applied to preserve their stability at the site of injury until regeneration is complete. While several gels and scaffold materials have been designed to deliver and hold stem cells at the site of regeneration, the ability of clay nanoparticles to overcome a second critical hurdle facing stem-cell therapy is what makes them especially exciting. Essential to directing the activity of stem-cells is the carefully controlled provision of key biological signalling molecules. However, the open structures of conventional scaffolds or gels, while essential for the diffusion of nutrients to the cells, means their ability to hold the signalling molecules in the same location as the cells is limited. The ability of clay nano-particles to bind biological molecules presents a unique opportunity to create local environments at a site of injury or disease that can stimulate and control stem-cell driven repair. Dr Dawson's early studies investigated the ability of clay gels to stimulate the growth of new blood vessels by incorporating a key molecular signal that stimulates this process, vascular endothelial growth factor (VEGF). In a manner reminiscent of the observations made in the 60s, Dr Dawson and colleagues observed that adding a drop of clay gel to a solution containing VEGF caused, after a few hours, the disappearance of VEGF from the solution as it became bound to the gel. When placed in an experimental injury model, the gel-bound VEGF stimulated a cluster of new blood vessels to form. These exciting results indicate the potential of clay nanoparticles to create tailor-made micro-environments to foster stem cell regeneration. Dr Dawson is developing this approach as a means of first exploring the biological signals necessary to successfully control stem cell behaviour for regeneration and then, using the same approach, to provide stem cells with these signals to stimulate regeneration in the body. The project will seek to test this approach to regenerate bone lost to cancer or hip replacement failure. If successful the same technology may be applied to harness stem cells for the treatment of a whole host of different scenarios, from burn victims to those suffering with diabetes or Parkinson's.

scholarly journals Tribological Properties of Al2O3 Nanoparticles as Lithium Grease Additives

Lubricants ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 9
Author(s):  
Ahmed Nabhan ◽  
Ahmed Rashed ◽  
Nouby M. Ghazaly ◽  
Jamil Abdo ◽  
M. Danish Haneef
Keyword(s):  
Tribological Properties ◽  
Wear Scar ◽  
Al2o3 Nanoparticles ◽  
Lithium Grease ◽  
Pin On Disc ◽  
Scar Width

The tribological properties of Lithium grease specimens with different concentrations of Al2O3 nanoparticles were investigated using a pin on disc apparatus under different sliding speeds and normal loads. Results showed that Al2O3 nanoparticles enhanced the tribological properties of lithium grease and reduced the COF and wear scar width by approximately 57.9% and 47.5% respectively.

scholarly journals In-Line Rheo-Optical Investigation of the Dispersion of Organoclay in a Polymer Matrix during Twin-Screw Compounding

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2128
Author(s):  
Paulo F. Teixeira ◽  
José A. Covas ◽  
Loïc Hilliou
Keyword(s):  
Local Heating ◽  
Polymer Nanocomposite ◽  
Structural Rearrangement ◽  
Particle Dispersion ◽  
Optical Investigation ◽  
Twin Screw Extrusion ◽  
Clay Particles ◽  
Clay Dispersion ◽  
Screw Extrusion ◽  
Twin Screw

The dispersion mechanisms in a clay-based polymer nanocomposite (CPNC) during twin-screw extrusion are studied by in-situ rheo-optical techniques, which relate the CPNC morphology with its viscosity. This methodology avoids the problems associated with post extrusion structural rearrangement. The polydimethylsiloxane (PDMS) matrix, which can be processed at ambient and low temperatures, is used to bypass any issues associated with thermal degradation. Local heating in the first part of the extruder allows testing of the usefulness of low matrix viscosity to enhance polymer intercalation before applying larger stresses for clay dispersion. The comparison of clay particle sizes measured in line with models for the kinetics of particle dispersion indicates that larger screw speeds promote the break-up of clay particles, whereas smaller screw speeds favor the erosion of the clay tactoids. Thus, different levels of clay dispersion are generated, which do not simply relate to a progressively better PDMS intercalation and higher clay exfoliation as screw speed is increased. Reducing the PDMS viscosity in the first mixing zone of the screw facilitates dispersion at lower screw speeds, but a complex interplay between stresses and residence times at larger screw speeds is observed. More importantly, the results underline that the use of larger stresses is inefficient per se in dispersing clay if sufficient time is not given for PDMS to intercalate the clay galleries and thus facilitate tactoid disruption or erosion.

Use of polysaccharide based surfactants to stabilize organically modified clay particles aqueous dispersion

2013 ◽  
Vol 94 (1) ◽  
pp. 687-694 ◽  
Author(s):  
Manja Kurečič ◽  
Majda Sfiligoj Smole ◽  
Karin Stana-Kleinschek
Keyword(s):  
Aqueous Dispersion ◽  
Clay Particles ◽  
Modified Clay ◽  
Organically Modified
Sign in / Sign up

Export Citation Format

Share Document