Electroflocculation as potential pretreatment in colloid ultrafiltration

2006 ◽  
Vol 6 (1) ◽  
pp. 69-78 ◽  
Author(s):  
T. Harif ◽  
M. Hai ◽  
A. Adin
Keyword(s):  
Membrane Fouling ◽  
Colloidal Suspension ◽  
Membrane Surface ◽  
Constant Current ◽  
Permeate Flux ◽  
Batch Mode ◽  
Membrane Behavior ◽  
Flux Decline ◽  
Stainless Steel Cathode ◽  
Marginal Improvement

Electroflocculation (EF) is a coagulation/flocculation process in which active coagulant species are generated in situ by electrolytic oxidation of an appropriate anode material. The effect of colloidal suspension pretreatment by EF on membrane fouling was measured by flux decline at constant pressure. An EF cell was operated in batch mode and comprised two flat sheet electrodes, an aluminium anode and stainless steel cathode, which were immersed in the treated suspension, and connected to an external DC power supply. The cell was run at constant current between 0.06–0.2A. The results show that pre-EF enhances the permeate flux at pH 5 and 6.5, but only marginal improvement is observed at pH 8. At all pH values cake formation on the membrane surface was observed. The differences in membrane behavior can be explained by conventional coagulation theory and transitions between aluminium mononuclear species which affect particle characteristics and consequently cake properties. At pH 6.5, where sweep floc mechanism dominates due to increased precipitation of aluminium hydroxide, increased flux rates were observed. It is evident that EF can serve as an efficient pretreatment to ultrafiltration of colloid particles.

scholarly journals Studies of polypropylene membrane fouling during microfiltration of broth with Citrobacter freundii bacteria

2015 ◽  
Vol 17 (4) ◽  
pp. 56-64 ◽  
Author(s):  
Marek Gryta ◽  
Marta Waszak ◽  
Maria Tomaszewska
Keyword(s):  
Membrane Fouling ◽  
Membrane Surface ◽  
Transmembrane Pressure ◽  
Citrobacter Freundii ◽  
Permeate Flux ◽  
Process Duration ◽  
Polypropylene Membrane ◽  
Flux Decline ◽  
Cake Layer ◽  
Scanning Electron

Abstract In this work a fouling study of polypropylene membranes used for microfiltration of glycerol solutions fermented by Citrobacter freundii bacteria was presented. The permeate free of C. freundii bacteria and having a turbidity in the range of 0.72–1.46 NTU was obtained. However, the initial permeate flux (100–110 L/m2h at 30 kPa of transmembrane pressure) was decreased 3–5 fold during 2–3 h of process duration. The performed scanning electron microscope observations confirmed that the filtered bacteria and suspensions present in the broth formed a cake layer on the membrane surface. A method of periodical module rinsing was used for restriction of the fouling influence on a flux decline. Rinsing with water removed most of the bacteria from the membrane surface, but did not permit to restore the initial permeate flux. It was confirmed that the irreversible fouling was dominated during broth filtration. The formed deposit was removed using a 1 wt% solution of sodium hydroxide as a rinsing solution.

Membrane fouling mechanisms and permeate flux decline model in soy sauce microfiltration

2017 ◽  
Vol 41 (1) ◽  
pp. e12599 ◽  
Author(s):  
Ye Sun ◽  
Zhen Qin ◽  
Liming Zhao ◽  
Qiming Chen ◽  
Qingyun Hou ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Soy Sauce ◽  
Permeate Flux ◽  
Flux Decline

A Wall Film Model for Membrane Fouling

2018 ◽  
Author(s):  
Sina Jahangiri Mamouri ◽  
Volodymyr V. Tarabara ◽  
André Bénard
Keyword(s):  
Multiphase Flow ◽  
Membrane Fouling ◽  
Oil And Gas ◽  
Membrane Separation ◽  
Film Formation ◽  
Membrane Surface ◽  
Permeate Flux ◽  
Water Separation ◽  
Wall Film ◽  
Oil Water

Deoiling of produced or impaired waters associated with oil and gas production represents a significant challenge for many companies. Centrifugation, air flotation, and hydrocyclone separation are the current methods of oil removal from produced water [1], however the efficiency of these methods decreases dramatically for droplets smaller than approximately 15–20 μm. More effective separation of oil-water mixtures into water and oil phases has the potential to both decrease the environmental footprint of the oil and gas industry and improve human well-being in regions such as the Gulf of Mexico. New membrane separation processes and design of systems with advanced flow management offer tremendous potential for improving oil-water separation efficacy. However, fouling is a major challenge in membrane separation [2]. In this study, the behavior of oil droplets and their interaction with crossflow filtration (CFF) membranes (including membrane fouling) is studied using computational fluid dynamics (CFD) simulations. A model for film formation on a membrane surface is proposed for the first time to simulate film formation on membrane surfaces. The bulk multiphase flow is modeled using an Eulerian-Eulerian multiphase flow model. A wall film is developed from mass and momentum balances [3] and implemented to model droplet deposition and membrane surface blockage. The model is used to predict film formation and subsequent membrane fouling, and allow to estimate the actual permeate flux. The results are validated using available experimental data.

Investigation of membrane fouling by synthetic and natural particles

2004 ◽  
Vol 50 (12) ◽  
pp. 279-285 ◽  
Author(s):  
J.H. Kweon ◽  
D.F. Lawler
Keyword(s):  
Organic Matter ◽  
Natural Organic Matter ◽  
Membrane Fouling ◽  
Membrane Surface ◽  
Research Articles ◽  
Clay Material ◽  
Dramatic Effect ◽  
Flux Decline ◽  
Scanning Electron

The biggest impediment for applying membrane processes is fouling that comes from mass flux (such as particle and organic matter) to the membrane surface and its pores. Numerous research articles have indicated that either particles or natural organic matter (NOM) has been the most detrimental foulant. Therefore, the role of particles in membrane fouling was investigated with two synthetic waters (having either particles alone or particles with simple organic matter) and a natural water. Membrane fouling was evaluated with flux decline behavior and direct images from scanning electron microscopy. The results showed that the combined fouling by kaolin and dextran (a simple organic compound selected as a surrogate for NOM) showed no difference from the fouling with only the organic matter. The similarity might stem from the fact that dextran (i.e., polysaccharide) has no ability to be adsorbed on the clay material, so that the polysaccharide behaves the same with respect to the membrane with or without clay material being present. In contrast to kaolin, the natural particles showed a dramatic effect on membrane fouling.

Influence of humic acid on the long-term performance of direct contact membrane distillation

2018 ◽  
Vol 30 (1) ◽  
pp. 109-120 ◽  
Author(s):  
Dong-Wan Cho ◽  
Gihoon Kwon ◽  
Jeongmin Han ◽  
Hocheol Song
Keyword(s):  
Humic Acid ◽  
Membrane Fouling ◽  
Coalbed Methane ◽  
Direct Contact ◽  
Membrane Surface ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Direct Contact Membrane Distillation ◽  
High Level

In this study, the influence of humic acid on the treatment of coalbed methane water by direct contact membrane distillation was examined with bench-scale test unit. During short-term distillation (1000 min), high level of humic acid above 50 ppm resulted in significant decrease in permeate flux, while low level of humic acid (∼2 ppm) had little influence on the flux. For the long-term distillation (5000 min), the flux decline began at 3400 min in the presence of 5 ppm humic acid and 5 mM Ca2+, and decreased to ∼40% of initial flux at 5000 min. The spectroscopic analysis of the membrane used revealed that the surface was covered by hydrophilic layers mainly composed of calcite. The membrane fouling effect of humic acid became more significant in the presence of Ca2+ due to more facile calcite formation on the membrane surface. It was demonstrated that humic acid enhanced CaCO3 deposition on the membrane surfaces, thereby expediting the scaling phenomenon.

Investigation of membrane fouling in ultrafiltration using model organic compounds

2005 ◽  
Vol 51 (6-7) ◽  
pp. 101-106 ◽  
Author(s):  
J.H. Kweon ◽  
D.F. Lawler
Keyword(s):  
Organic Compounds ◽  
Membrane Fouling ◽  
Alginic Acid ◽  
Membrane Surface ◽  
Sem Images ◽  
Membrane Processes ◽  
Xps Spectra ◽  
Relative Composition ◽  
Flux Decline ◽  
The City

Natural organic matter (NOM) is known to be the worst foulant in the membrane processes, but the complexities of NOM make it difficult to determine its effects on membrane fouling. Therefore, simple organic compounds (surrogates for NOM) were used in this research to investigate the fouling mechanisms in ultrafiltration. Previous research on NOM components in membrane processes indicated that polysaccharides formed an important part of the fouling cake. Three polysaccharides (dextran, alginic acid, and polygalacturonic acid) and a smaller carbohydrate (tannic acid) were evaluated for their removal in softening (the treatment process in the City of Austin). Two polysaccharides (dextran and alginic acid) were selected and further investigated for their effects on membrane fouling. The two raw organic waters (4 mg/L C) showed quite different patterns of flux decline indicating different fouling mechanisms. Softening pretreatment was effective to reduce flux decline of both waters. The SEM images of the fouled membrane clearly showed the shapes of deposited foulants. The high resolution results of the XPS spectra showed substantially different spectra of carbon, C(1s), in the membrane fouled by two raw organic waters. The XPS was beneficial in determining the relative composition of each fouling material on the membrane surface.

Chemical pretreatment of feed water for membrane distillation

2008 ◽  
Vol 62 (1) ◽  
Author(s):  
Marek Gryta
Keyword(s):  
Membrane Fouling ◽  
Membrane Surface ◽  
Membrane Distillation ◽  
Feed Water ◽  
Chemical Pretreatment ◽  
Permeate Flux ◽  
Membrane Scaling ◽  
Water Pretreatment ◽  
Energy Dispersion Spectrometry ◽  
Process Operation

AbstractMembrane distillation was used to produce demineralized water from ground water. The influence of feed water pretreatment carried out in a contact clarifier (softening with Ca(OH)2 and coagulation with FeSO4 · 7H2O) followed by filtration, on the process effectiveness was evaluated. It was found that the chemical pretreatment decreased the membrane fouling; however, the degree of water purification was insufficient because precipitation of small amounts of deposit on the membrane surface during the process operation was still observed. The permeate flux was gradually decreasing as a result of scaling. The morphology and composition of the fouling layer were studied using scanning electron microscopy coupled with energy dispersion spectrometry. The presence of significant amounts of silica, apart from calcium and magnesium, was determined in the formed deposit. The removal of foulants by heterogeneous crystallization performed inside the filter (70 mesh), assembled directly at the module inlet, was found to be a solution preventing the membrane scaling.

A real trial of a long-term non-fouling membrane bioreactor for saline sewage treatment

2011 ◽  
Vol 63 (7) ◽  
pp. 1519-1523 ◽  
Author(s):  
Peng Bai ◽  
Jin Wang ◽  
Guang-Hao Chen
Keyword(s):  
Membrane Fouling ◽  
Membrane Bioreactor ◽  
Membrane Surface ◽  
Pilot Trial ◽  
Sewage Treatment ◽  
Power Source ◽  
Permeate Flux ◽  
Mixing Condition ◽  
Water Ratio

This paper reports on a pilot trial of a novel MBR developed with coarse-pore membrane module by the authors. The plant was operated for 370 days with up to 7 m3/d raw saline sewage after 3-mm screening. The plant performed successfully without membrane fouling for 270 days except an accidental power source failure for 30 h, during which membrane was fouled under no aeration and mixing condition. EPS increases in both the reactor and the bio-cake on the membrane surface explained this fouling. The average TSS, COD and TKN removal efficiency were 92, 90, and 93%, respectively, under a high effective permeate flux of 4.8 m/d and a low air-to-water ratio of 15.

scholarly journals Effect of on the Membrane Distillation of PVDF Membrane Material Enhanced by Gas-Liquid Two-Phase Flow

2018 ◽  
Vol 2 (1) ◽  
Keyword(s):  
Membrane Surface ◽  
Threshold Level ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
High Concentration ◽  
Two Phase ◽  
Flux Enhancement ◽  
Membrane Performance ◽  
Flux Decline ◽  
Sweeping Gas

This study investigates the membrane performance and fouling control in the bubble-assisted sweeping gas membrane distillation with high concentration saline (333 K saturated solution) as feed. The results show that longer bubbling interval (3 min) at a fixed bubbling duration of 30s can most efficiently increase the the flux enhancement ratio up to 1.518. Next, the flux increases with the gas flowrate under a relatively lower level, but tends to a plateau after the threshold level (1.2 L•min-1). Compared to non-bubbling case, the permeate flux reaches up to 1.623 fold at a higher bubble relative humidity of 80 %. It was also found that greater flux enhancement can be achieved and meanwhile dramatic flux decline can be delayed for an intermittent bubbling system with a smaller nozzle size. These results accord well with the observations of fouling deposition in situ on the membrane surface with SEM.

Effect of coagulation mechanisms on the fouling and ultrasonic cleaning of PTFE membrane

2012 ◽  
Vol 66 (11) ◽  
pp. 2291-2298 ◽  
Author(s):  
Meng-Wei Wan ◽  
Cybelle Morales Futalan ◽  
Cheng-Hung Chang ◽  
Chi-Chuah Kan
Keyword(s):  
Membrane Fouling ◽  
Permeate Flux ◽  
Cleaning Efficiency ◽  
Ultrasonic Cleaning ◽  
Ptfe Membrane ◽  
Pore Blocking ◽  
Dead End ◽  
Flux Decline ◽  
Cake Formation ◽  
Scanning Electron

In this study, the effect of coagulation pretreatment on membrane fouling and ultrasonic cleaning efficiency was investigated using a dead-end polytetrafluoroethylene (PTFE) microfiltration system. The extent of membrane fouling was examined under different coagulation mechanisms such as charge neutralization (CN), electrostatic patch effect (EPE) and sweep flocculation (SW). Fouling through EPE mechanism provided the greatest flux decline and least permeate flux recovery over CN and SW. EPE produces more stable, smaller and more compact flocs while CN and SW have large, easily degraded and highly-branched structured flocs. The predominant fouling mechanism of EPE, CN and SW is pore blocking, a combination of pore blocking and cake formation, and cake formation, respectively. Better permeate flux recovery is observed with SW over CN and EPE, which implies formation of less dense and more porous cake deposits. The morphology of fouled membranes was examined using scanning electron microscopy (SEM).

Sign in / Sign up

Export Citation Format

Share Document