Cysteine-modified orange peel for removal of Cu(II) from aqueous solutions

2013 ◽  
Vol 67 (11) ◽  
pp. 2444-2450 ◽  
Author(s):  
Mingdeng Liu ◽  
Qunhui Yuan ◽  
Hanzhong Jia ◽  
Shouzhu Li ◽  
Xiaohuan Wang ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Contact Time ◽  
Orange Peel ◽  
Aqueous System ◽  
Order Equation ◽  
Initial Ph ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Influential Parameters ◽  
Better Than

In the present work, cysteine-modified orange peel (COP) for the removal of Cu(II) from aqueous solutions has been developed and comparatively studied with diethylenetriamine-modified orange peel (DOP). Both COP and DOP were systematically evaluated via their capabilities for adsorbing Cu(II), including the key influential parameters such as initial pH, contact time and initial Cu(II) concentration. Further studies suggest that the sorption of Cu(II) onto both COP and DOP fits well with the pseudo-second-order equation, and the corresponding sorption isotherm can be classified to a Langmuir isotherm model. COP appears more advantageous over DOP and far better than that of unmodified OP in removal of Cu(II) from aqueous system. The maximum capacities of COP and DOP for adsorbing Cu(II) are 95.23 and 83.68 mg/g, respectively, about three times higher than that of unmodified OP. The sorption efficiency of COP drops by merely about 3% after five cycles, implying a promising usage in the removal of Cu(II) from wastewater in practice.

scholarly journals Husk of Agarwood Fruit-Based Hydrogel Beads for Adsorption of Cationic and Anionic Dyes in Aqueous Solutions

Molecules ◽  
2021 ◽  
Vol 26 (5) ◽  
pp. 1437
Author(s):  
Chih Ming Ma ◽  
Bo-Yuan Yang ◽  
Gui-Bing Hong
Keyword(s):  
Aqueous Solutions ◽  
Selective Adsorption ◽  
Order Model ◽  
Anionic Dyes ◽  
Adsorption Selectivity ◽  
Hydrogel Beads ◽  
Batch System ◽  
Initial Ph ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

Hydrogel beads based on the husk of agarwood fruit (HAF)/sodium alginate (SA), and based on the HAF/chitosan (CS) were developed for the removal of the dyes, crystal violet (CV) and reactive blue 4 (RB4), in aqueous solutions, respectively. The effects of the initial pH (2–10) of the dye solution, the adsorbent dosage (0.5–3.5 g/L), and contact time (0–540 min) were investigated in a batch system. The dynamic adsorption behavior of CV and RB4 can be represented well by the pseudo-second-order model and pseudo-first-order model, respectively. In addition, the adsorption isotherm data can be explained by the Langmuir isotherm model. Both hydrogel beads have acceptable adsorption selectivity and reusability for the study of selective adsorption and regeneration. Based on the effectiveness, selectivity, and reusability of these hydrogel beads, they can be treated as potential adsorbents for the removal of dyes in aqueous solutions.

Removal of Cr(VI) from Aqueous Solutions Using Clay from Calumbi Geological Formation, N. Sra. Socorro, SE State, Brazil

2018 ◽  
Vol 912 ◽  
pp. 1-6 ◽  
Author(s):  
J.C.T. Rezende ◽  
V.H.S. Ramos ◽  
H.A. Oliveira ◽  
Rosane Maria Pessoa Betânio Oliveira ◽  
E. Jesus
Keyword(s):  
Aqueous Solutions ◽  
Contact Time ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Initial Ph ◽  
Geological Formation ◽  
Langmuir Isotherm Model

Conventional processes for heavy metal removal are costly. Natural and modified clay with quaternary ammonium salt were used as adsorbent for the removal of Cr (VI) from aqueous solutions. Clays were characterized using Fourier transform infrared spectroscopy FTIR, thermal analysis (TG/DTA) and X-ray diffraction (XRD). Cr (VI) determination was conducted by ultraviolet-visible spectrophotometry, using complexation with 1,5-diphenylcarbazide. Absorbance was measured at the wavelength of 540 nm. The experiments were conducted at 25 ± 1 °C; initial Cr (VI) concentration of 4 to 25 mg L-1; initial pH of 2, agitation of 150 rpm; contact time of 120 minutes and clay mass of 0.1 g. Natural and modified clays exhibited a maximum adsorption capacity of 2.548 mg g-1 and 17.24 mg g-1, respectively, in accordance with the Langmuir isotherm model. X-ray diffraction analysis of clay indicated that the sample consists mainly of kaolinite and montmorillonite.

Removal of Methyl Red from Aqueous Solution by Adsorption onto Mg-Al HTLc

2013 ◽  
Vol 750-752 ◽  
pp. 1426-1429
Author(s):  
Yun Bo Zang
Keyword(s):  
Aqueous Solution ◽  
Aqueous Solutions ◽  
Contact Time ◽  
Adsorption Process ◽  
Bulk Solution ◽  
Methyl Red ◽  
Initial Ph ◽  
Pseudo Second Order ◽  
Ph Range ◽  
Percent Removal

In this study, removal of Methyl Red from aqueous solutions by synthetic Mg-Al-HTlc was investigated as a function of contact time, pH and temperature. It is found that HTlc could reduced Methyl Red concentration effectively. The kinetic process which reached equilibrium at about 2h can be fitted by pseudo-second order kinetics. The percent removal of MR by the HTlc was dependent on the initial pH of bulk solution. There was no much changes in amount of adsorption in the initial pH range of 6-8, while it reached maxium at about of 9. The adsorption process was endothermic.

Adsorption of enrofloxacin from aqueous solution by bentonite

Clay Minerals ◽  
2013 ◽  
Vol 48 (4) ◽  
pp. 627-637 ◽  
Author(s):  
J. X. Zhang ◽  
Q. X. Zhou ◽  
W. Li
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Adsorption Equilibrium ◽  
Order Kinetic ◽  
Batch Experiments ◽  
Freundlich Model ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Better Than

AbstractThe removal of enrofloxacin, a fluoroquinolone antibiotic, from aqueous solution by adsorption onto bentonite was investigated in this study. The effects of initial concentrations, contact time and temperature on the adsorption of enrofloxacin were studied via batch experiments. The adsorption equilibrium was achieved within 60 min for all studied concentrations. The adsorption capacity increased with the increase of initial concentration within a concentration range. Higher temperatures were favourable for the adsorption. The change of Gibbs free energy (ΔG°), change of enthalpy (ΔH°) and change of entropy (ΔS°) were evaluated and the results indicate that the adsorption should be an endothermic and spontaneous process. The Langmuir isotherm model fitted to the experimental data better than the Freundlich model. The adsorption follows the pseudo-second order kinetic model.

Adsorption of Cr (VI) from Aqueous Solution by Purified Attapulgite

2014 ◽  
Vol 1051 ◽  
pp. 583-587
Author(s):  
Ling Tao ◽  
Xiao Wei Song ◽  
Jian Li Yuan ◽  
Jun Ren ◽  
Yan Zhuo Zhang
Keyword(s):  
Aqueous Solution ◽  
Adsorption Isotherm ◽  
Aqueous Solutions ◽  
Contact Time ◽  
Order Equation ◽  
Langmuir Model ◽  
Initial Concentration ◽  
Pseudo Second Order ◽  
Equilibrium Adsorption Isotherm ◽  
Good Agreement

Adsorption of Cr6+ onto purified attapulgite was investigated with respect to temperature, initial concentration and contact time. The kinetics data related to the adsorption of chromium from aqueous solutions are in good agreement with the pseudo-second order equation in ranges of initial concentration of 20~200 mg/L, and temperature of 298~328K. The thermodynamic experiment results show that the equilibrium adsorption isotherm was closely fitted with the Langmuir model.

Nano-ZrO2/TiO2 Impregnated Orange Wood Sawdust and Peach Stone Shell Adsorbents for Cr (VI) Removal

2020 ◽  
Vol 16 (7) ◽  
pp. 880-892
Author(s):  
Şerife Parlayıcı ◽  
Kübra Tuna Sezer ◽  
Erol Pehlivan
Keyword(s):  
Contact Time ◽  
Ph Value ◽  
Order Kinetic ◽  
Adsorption Parameters ◽  
Wood Sawdust ◽  
Adsorption Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Equilibrium Status

Background: In this work, Cr (VI) adsorption on nano-ZrO2๏TiO2 impregnated orange wood sawdust (Zr๏Ti/OWS) and nano-ZrO2๏TiO2 impregnated peach stone shell (Zr๏Ti/PSS) was investigated by applying different adsorption parameters such as Cr (VI) concentrations, contact time, adsorbent dose, and pH for all adsorbents. Methods: The adsorbents were characterized by SEM and FT-IR. The equilibrium status was achieved after 120 min of contact time and optimum pH value around 2 were determined for Cr (VI) adsorption. Adsorption data in the equilibrium is well-assembled by the Langmuir model during the adsorption process. Results: Langmuir isotherm model showed a maximum adsorption value of OWS: 21.65 mg/g and Zr๏Ti/OWS: 27.25 mg/g. The same isotherm displayed a maximum adsorption value of PSS: 17.64 mg/g, and Zr๏Ti/PSS: 31.15 mg/g. Pseudo-second-order kinetic models (R2=0.99) were found to be the best models for describing the Cr (VI) adsorption reactions. Conclusıon: Thermodynamic parameters such as changes in ΔG°, ΔH°, and ΔS° have been estimated, and the process was found to be spontaneous.

Biosorption of As(V) from aqueous solutions by living cells of Bacillus cereus

2012 ◽  
Vol 66 (8) ◽  
pp. 1699-1707 ◽  
Author(s):  
A. K. Giri ◽  
R. K. Patel ◽  
P. C. Mishra
Keyword(s):  
Aqueous Solutions ◽  
Bacillus Cereus ◽  
Contact Time ◽  
Living Cells ◽  
Optimum Conditions ◽  
Order Model ◽  
Initial Concentration ◽  
Pseudo Second Order ◽  
Biomass Dosage ◽  
Batch Biosorption

In this work, the biosorption of As(V) from aqueous solutions by living cells of Bacillus cereus has been reported. The batch biosorption experiments were conducted with respect to biosorbent dosage 0.5 to 15 g/L, pH 2 to 9, contact time 5 to 90 min, initial concentration 1 to 10 mg/L and temperature 10 to 40 °C. The maximum biosorption capacity of B. cereus for As(V) was found to be 30.04 at pH 7.0, at optimum conditions of contact time of 30 min, biomass dosage of 6 g/L, and temperature of 30 ± 2 °C. Biosorption data were fitted to linearly transformed Langmuir isotherms with R2 (correlation coefficient) >0.99. Bacillus cereus cell surface was characterized using AFM and FTIR. The metal ions were desorbed from B. cereus using both 1 M HCl and 1 M HNO3. The pseudo-second-order model was successfully applied to predict the rate constant of biosorption.

scholarly journals Photocatalytic Degradation of Naphthalene By UV/Zno: Kinetics, Influencing Factors and Mechanisms

2021 ◽  
Vol 37 (1) ◽  
pp. 65-70
Author(s):  
Aram Dokht Khatibi ◽  
Kethineni Chandrika ◽  
Ferdos Kord Mostafapour ◽  
Ali Akbar Sajadi ◽  
Davoud Balarak
Keyword(s):  
Wastewater Treatment ◽  
Reaction Time ◽  
Aqueous Solutions ◽  
Aromatic Hydrocarbons ◽  
Contact Time ◽  
Initial Concentration ◽  
Applied Study ◽  
Batch System ◽  
Initial Ph ◽  
Conventional Wastewater Treatment

Conventional wastewater treatment is not able to effectively remove Aromatic hydrocarbons such as Naphthalene, so it is important to remove the remaining antibiotics from the environment. The aim of this study was to evaluate the efficiency of UV/ZnOphotocatalytic process in removing naphthalene antibiotics from aqueous solutions.This was an experimental-applied study that was performed in a batch system on a laboratory scale. The variables studied in this study include the initial pH of the solution, the dose of ZnO, reaction time and initial concentration of Naphthalene were examined. The amount of naphthalene in the samples was measured using GC.The results showed that by decreasing the pH and decreasing the initial concentration of naphthalene and increasing the contact time, the efficiency of the process was developed. However, an increase in the dose of nanoparticles to 0.8 g/L had enhance the efficiency of the process was enhanced, while increasing its amount to values higher than 0.8 g/L has been associated with a decrease in removal efficiency.The results of this study showed that the use of UV/ZnOphotocatalytic process can be addressed as a well-organized method to remove naphthalene from aqueous solutions.

scholarly journals Utilization of Lapindo Volcanic Mud for Enhanced Sono-sorption Removal of Acid Orange 52

2019 ◽  
Vol 14 (1) ◽  
pp. 189
Author(s):  
Nur Hidayatul Nazirah Kamarudin ◽  
Herma Dina Setiabudi ◽  
Aishah Abdul Jalil ◽  
Siti Hazirah Adam ◽  
Nur Fatien Muhamad Salleh
Keyword(s):  
Adsorption Process ◽  
Order Equation ◽  
Reaction Engineering ◽  
Adsorption Method ◽  
Adsorption Ability ◽  
Acid Orange ◽  
Isotherm Study ◽  
Sorption Method ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

This study applied ultrasonic irradiation technique to remove acid orange 52 (AO52) and in the meantime utilizing the potential adsorbent, Lapindo volcanic mud (LVM). LVM was collected from the erupted mud in Sidoarjo, Indonesia and calcined prior the adsorption process. Previously in another study, Lapindo was proven to be efficient for adsorption of dyes in single adsorption method. In this study, the combination of adsorption with ultrasound, or as known as sono-sorption shows that the adsorptivity increased from 95.54 mg/g to 129.5 mg/g. The isotherm study shows that this process obeyed Langmuir isotherm model with adsorption capacity of 833.33 mg/g. The enhancement of sono-sorption method as compared to conventional method is believed to be resulted from the facilitated mass transfer driven by the ultrasound, along with the adsorption ability of LVM. The kinetic study fit to the pseudo second order equation. Copyright © 2019 BCREC Group. All rights reservedReceived: 1st October 2018; Revised: 22nd December 2018; Accepted: 7th January 2019; Available online: 25th January 2019; Published regularly: April 2019How to Cite: Kamarudin, N.H.N., Setiabudi, H.D., Jalil, A.A., Adam, S.H., Salleh, N.F.M. (2019). Utilization of Lapindo Volcanic Mud for Enhanced Sono-sorption Removal of Acid Orange 52. Bulletin of Chemical Reaction Engineering & Catalysis, 14 (1): 189-195 (doi:10.9767/bcrec.14.1.3326.189-195)Permalink/DOI: https://doi.org/10.9767/bcrec.14.1.3326.189-195  

scholarly journals Adsorption of Lead (II) from Aqueous Solution with High Efficiency by Hydrothermal Biochar Derived from Honey

2020 ◽  
Vol 17 (10) ◽  
pp. 3441 ◽  
Author(s):  
Bo Wang ◽  
Jie Yu ◽  
Hui Liao ◽  
Wenkun Zhu ◽  
Pingping Ding ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Photoelectron Spectroscopy ◽  
High Efficiency ◽  
Raw Material ◽  
Before And After ◽  
Initial Ph ◽  
Carboxylic Groups ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Natural Honey

A novel natural honey hydrothermal biochar (HHTB) was prepared using natural honey as raw material. The as-prepared adsorbent was applied to adsorb Pb2+ from aqueous solution and characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy to investigate the structure and morphology change of the adsorbent before and after Pb2+ adsorption. The influence of the pH, initial Pb2+ concentration, temperature, and contact time on the adsorption of Pb2+ was systematically investigated. The results revealed that the adsorption capacity for Pb2+ is up to 133.2 mg·g−1 at initial pH of 5.0 and adsorption temperature of 298 K. Meanwhile, the adsorption of Pb2+ on HHTB can be well fitted by the pseudo-second-order model and Langmuir isotherm model. The adsorbent had great selectivity for Pb2+ from the aqueous solution containing coexisting ions including Cd2+, Co2+, Cr3+, Cu2+, Ni2+ and Zn2+. Furthermore, the adsorption of Pb2+ on HHTB was attributed to complexation coordination, where it involved hydroxyl and carboxylic groups on HHTB in the process of adsorption of Pb2+.

Sign in / Sign up

Export Citation Format

Share Document