Nano-ZrO2/TiO2 Impregnated Orange Wood Sawdust and Peach Stone Shell Adsorbents for Cr (VI) Removal

2020 ◽  
Vol 16 (7) ◽  
pp. 880-892
Author(s):  
Şerife Parlayıcı ◽  
Kübra Tuna Sezer ◽  
Erol Pehlivan
Keyword(s):  
Contact Time ◽  
Ph Value ◽  
Order Kinetic ◽  
Adsorption Parameters ◽  
Wood Sawdust ◽  
Adsorption Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Equilibrium Status

Background: In this work, Cr (VI) adsorption on nano-ZrO2๏TiO2 impregnated orange wood sawdust (Zr๏Ti/OWS) and nano-ZrO2๏TiO2 impregnated peach stone shell (Zr๏Ti/PSS) was investigated by applying different adsorption parameters such as Cr (VI) concentrations, contact time, adsorbent dose, and pH for all adsorbents. Methods: The adsorbents were characterized by SEM and FT-IR. The equilibrium status was achieved after 120 min of contact time and optimum pH value around 2 were determined for Cr (VI) adsorption. Adsorption data in the equilibrium is well-assembled by the Langmuir model during the adsorption process. Results: Langmuir isotherm model showed a maximum adsorption value of OWS: 21.65 mg/g and Zr๏Ti/OWS: 27.25 mg/g. The same isotherm displayed a maximum adsorption value of PSS: 17.64 mg/g, and Zr๏Ti/PSS: 31.15 mg/g. Pseudo-second-order kinetic models (R2=0.99) were found to be the best models for describing the Cr (VI) adsorption reactions. Conclusıon: Thermodynamic parameters such as changes in ΔG°, ΔH°, and ΔS° have been estimated, and the process was found to be spontaneous.

Adsorption of Cu(II), Ni(II) and Zn(II) ions by nano kaolinite: Thermodynamics and kinetics studies

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Metal Ions ◽  
Metal Ion ◽  
Adsorption Process ◽  
Ion Concentration ◽  
Order Kinetic ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir

An easy route for preparation emulsion of kaolinite (Al2Si2O5.4H2O) from Sweileh sand deposits, west Amman, Jordan by hydrochloric acid under continuous stirring for 4 h at room temperature was performed and nano kaolinite powder was used as an adsorbent for the removal of Cu(II), Zn(II) and Ni(II) ions. Nano kaolinite was characterized by XRD, FT-IR and SEM techniques. Effect of pH, adsorbent dose, initial metal ion concentration, contact time and temperature on adsorption process was examined. The negative values of ΔGo and the positive value of ΔHo revealed that the adsorption process was spontaneous and endothermic. The Langmuir isotherm model fitted well to metal ions adsorption data and the adsorption capacity. The kinetic data provided the best correlation of the adsorption with pseudo-second order kinetic model. In view of promising efficiency, the nano kaolinite can be employed for heavy metal ions adsorption.

REMOVAL OF STRONTIUM (II) FROM AQUEOUS SOLUTION USING FUNCTIONALIZED CARBON NANOTUBES

2012 ◽  
Vol 11 (02) ◽  
pp. 1250019 ◽  
Author(s):  
RAJESH KUMAR ◽  
S. K. JAIN
Keyword(s):  
Carbon Nanotubes ◽  
Polluted Water ◽  
Order Kinetic ◽  
Environmental Application ◽  
Functionalized Carbon Nanotubes ◽  
Multi Wall Carbon Nanotubes ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Ft Ir

This study was carried out to evaluate the environmental application of functionalized carbon nanotubes through the experimental removal of strontium (II) from water. The aim was to find the optimal condition for the removal of strontium from water under different conditions such as initial concentration of strontium, contact time and neutral pH. The functionalized multi wall carbon nanotubes (f-MWCNT) were characterized by FT-IR and scanning electron microscopy (SEM). The adsorption isotherms were correlated to Freundlich and Langmuir models and it was found that the adsorption data could be fitted better by Langmuir model than Freundlich one. The kinetic data shows that the adsorption describes well with the pseudo-second order kinetic model. Functionalized MWCNT can be used as good adsorbent for the removal of the strontium ions from polluted water according to results.

Adsorption of Methylene Blue from Aqueous Solution Using Honeycomb-Cinder

2012 ◽  
Vol 550-553 ◽  
pp. 2259-2262
Author(s):  
Song Bo Cui ◽  
Hua Yong Zhang ◽  
Lu Yi Zhang
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Ph Value ◽  
Dye Wastewater ◽  
Batch System ◽  
Adsorption Data ◽  
Adsorption Processes ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Mb Adsorption

The adsorption behavior of methylene blue (MB) dye from aqueous solutions onto honeycomb-cinder (HC) and its acid-activated product was investigated in a batch system. The results showed the adsorption capacity was decreased for raw HC samples with the increase of pH value, while it was increased for activated samples. The adsorption data were fit with Langmuir isotherm model for MB adsorption by all samples. The MB adsorption capacity on samples was increased from 2.62 mg/g to 7.81 mg/g and 7.00 mg/g after acid-activated by HCl and H2SO4, respectively. The adsorption processes of MB followed pseudo-second-order kinetics with a coefficient of correlation≥0.99. This study demonstrated that acid-activated HC has superior adsorbing ability for MB than raw HC and can be used as alternative adsorbents in dye wastewater treatment.

scholarly journals Sythesis of Nano Zerovalent Iron Supported Sawdust (NZVI/SD) and Its Application for Removal of Arsenic (III) from Aqueous Solution

2020 ◽  
pp. 1-12
Author(s):  
Tasrina R. Choudhury ◽  
Snahasish Bhowmik ◽  
M. S. Rahman ◽  
Mithun R. Nath ◽  
F. N. Jahan ◽  
...  
Keyword(s):  
Ph Value ◽  
Ferrous Sulphate ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Zerovalent Iron ◽  
Isotherm Model ◽  
Order Kinetic ◽  
Adsorption Sites ◽  
Adsorption Data ◽  
Pseudo Second Order

Sawdust supported nano-zerovalent (NZVI/SD) iron was synthesized by treating sawdust with ferrous sulphate followed by reduction with NaBH4. The NZVI/SD was characterized by SEM, XRD, FTIR and Chemical method. Adsorption of As (III) by NZVI/SD was investigated and the maximum uptake of As (III) was found at pH value of 7.74 and equilibrium time of 3 hrs. The adsorption isotherm modelling revealed that the equilibrium adsorption data were better fitted with the Langmuir isotherm model compared with the Freundlich Isotherm model. This study revealed that the maximum As (III) ions adsorption capacity was found to be 12.66 mg/g for using NZVI/SD adsorbent. However, the kinetics data were tested by pseudo-first-order and pseudo-second-order kinetic models; and it was observed that the adsorption data could be well fitted with pseudo-second-order kinetics for As (III) adsorption onto NZVI/SD depending on both adsorbate concentration and adsorption sites. The result of this study suggested that NZVI/SD could be developed as a prominent environment-friendly adsorbent for the removal of As (III) ions from aqueous systems.

scholarly journals Preparation of chitosan/amine modified diatomite composites and adsorption properties of Hg(II) ions

2018 ◽  
Vol 77 (5) ◽  
pp. 1363-1371 ◽  
Author(s):  
Yong Fu ◽  
Yue Huang ◽  
Jianshe Hu ◽  
Zhengjie Zhang
Keyword(s):  
Schiff Base ◽  
Contact Time ◽  
Ph Value ◽  
Adsorption Properties ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Adsorption Effect ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Modified Diatomite

Abstract A green functional adsorbent (CAD) was prepared by Schiff base reaction of chitosan and amino-modified diatomite. The morphology, structure and adsorption properties of the CAD were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy and Brunauer Emmett Teller measurements. The effect of pH value, contact time and temperature on the adsorption of Hg(II) ions for the CAD is discussed in detail. The experimental results showed that the CAD had a large specific surface area and multifunctional groups such as amino, hydroxyl and Schiff base. The optimum adsorption effect was obtained when the pH value, temperature and contact time were 4, 25 °C and 120 min, respectively, and the corresponding maximum adsorption capacity of Hg(II) ions reached 102 mg/g. Moreover, the adsorption behavior of Hg(II) ions for the CAD followed the pseudo-second-order kinetic model and Langmuir model. The negative ΔG0 and ΔH0 suggested that the adsorption was a spontaneous exothermic process.

scholarly journals Adsorption Of Cd(II) Ions From Aqueous Solution By A Low-Cost Biosorbent Prepared From Ipomea Pes-Caprae Stem

2020 ◽  
Vol 9 (3) ◽  
pp. 197-206
Author(s):  
Thaharah Ramadhani ◽  
Faisal Abdullah ◽  
Indra Indra ◽  
Abrar Muslim ◽  
Suhendrayatna Suhendrayatna ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Optimal Condition ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Low Cost ◽  
Ph Values ◽  
Monolayer Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir

The use of a low-cost biosorbent prepared from Ipomoea pes-caprae stem for the adsorption of Cd(II) ions from aqueous solution at different contact times, biosorbent sizes, pH values, and initial Cd(II) ions concentration solution was investigated. The biosorbent was analyzed using Fourier-transform infrared spectroscopy (FT-IR) to find important IR-active functional groups. A scanning electron microscope (SEM) was used to examine the biosorbent morphology. The experimental results showed the highest Cd(II) ions adsorption was 29.513 mg/g  under an optimal condition as initial Cd(II) ions concentration of 662.77 mg/L, 1 g dose, 80-min contact time, pH 5, 75 rpm of stirring speed, 1 atm, and 30 oC. Cd(II) ions' adsorption kinetics obeys the linearized pseudo-second-order kinetics (R2 = 0.996), and the adsorption capacity is based on the optimal condition, and the rate attained was 44.444 mg/g and 0.097 g/mg. Min, respectively. Besides, the adsorption isotherms were very well fitted by the linearized Langmuir isotherm model, and the monolayer adsorption capacity and pore volume determined was 30.121 mg/g and 0.129 L/mg, respectively. These results indicated the chemisorption nature

scholarly journals Removal of Cu(II) Ions byLeucaena Leucocephala(Subabul) Seed Pods from Aqueous Solutions

2010 ◽  
Vol 7 (s1) ◽  
pp. S377-S385 ◽  
Author(s):  
A. K. Patil ◽  
V. S. Shrivastava
Keyword(s):  
Leucaena Leucocephala ◽  
Contact Time ◽  
Unit Weight ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Isotherm Equations ◽  
Adsorbent Dose

In this method,Leucaena leucocephalaseed pods (LLSP) have been used for removal of Cu(II) ions from aqueous solution. Batch adsorption experiments were conducted to study the effect of process parameters like pH, contact time initial Cu(II) ions concentration and adsorbent dose. The maximum adsorption of Cu(II) ions onLeucaena leucocephalaseed pods was 94.17% at pH 5. The amount of metal adsorbed per unit weight of adsorbent increases with time and reach equilibrium after 30 minutes of shaking time for the different initial metal concentrations. The Freundlich and Langmuir isotherm equations were applied for the equilibrium adsorption data and the various isotherm parameters were evaluated. The obtained plots were linear as evident fromR2values close to unity. The data agreed very well with the pseudo second-order kinetic model.

scholarly journals KINETIC AND ISOTHERM STUDY OF CUPPER ADSORPTION FROM AQUEOUS SOLUTION USING WASTE EGGSHELL

2014 ◽  
Vol 22 (2) ◽  
pp. 132-140 ◽  
Author(s):  
Ayben Polat ◽  
Sukru Aslan
Keyword(s):  
Ph Value ◽  
Experimental System ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Isotherm Study ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The sorption of Cu2+ ions from aqueous solutions by eggshell was investigated in a batch experimental system with respect to the temperature, initial Cu2+ concentrations, pH, and biosorbent doses. The adsorption equilibrium was well described by the Langmuir isotherm model with the maximum adsorption capacity of 5.05 mg Cu2+/g eggshell at 25 °C. The value of qe increased with increasing the temperature while also increases the release of Ca2+ and HCO−3 ions from the eggshell. The highest sorption of Cu onto the waste eggshell was determined at the initial pH value of 4.0. The results confirming that the adsorption reaction of Cu2+ on the eggshell was thought to be endothermic. A comparison of the kinetic models such as pseudo first and second-order kinetics, intraparticle diffusion, and Elovich on the sorption rate demonstrated that the system was best described by the pseudo second-order kinetic model.

Adsorption Characters of Mn2+ onto Palygorskites Modified by 1, 10-Phenanthroline and Triethylamine

2010 ◽  
Vol 178 ◽  
pp. 8-16
Author(s):  
Liang Dong Feng ◽  
Bo Qing Chen ◽  
Ying Ying Shi ◽  
Ying Wei Guo ◽  
Jing Huang ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Ph Value ◽  
Order Model ◽  
Kinetics Of Adsorption ◽  
Initial Concentration ◽  
Adsorption Capacities ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Kinetics Of

1, 10-phenanthroline and triethylamine modified palygorskites were prepared by microwave irradiation, and characterized with FT-IR technique. The effects of contact time, adsorbent dosage, and pH value of the initial solution on the adsorption characters of Mn2+ were investigated. The adsorption of Mn2+ from aqueous solutions using 1, 10-phenanthroline or triethylamine modified palygorskites were investigated. Experiment results indicated that 1,10-phenanthroline and triethylamine molecules have been successfully grafted to palygorskite. The adsorption was rapid during the first 5 minuts and equilibrium were attained within 60 minutes in the initial concentration of Mn2+ of 50 and 100 mg•L-1, and fast adsorption in the first 10 minutes and slowly increased with the contact time due to the adsorption of palygorskite. The 1, 10-phenanthroline modified palygorskites had higher adsorption capacity than triethylamine modified palygorskites. Compared with natural palggorskites, the Mn2+ ions adsorption capacities of palggorskite modified by 1, 10-phenanthroline or triethylamine were significantly improved. There were less difference in the adsorption capacity between different dasages of 1, 10-phenanthroline modified palygorskites, but the adsorption capacity of Mn2+ adsorbed onto triethylamine modified palygorskites decreased with increasing the dosages. A Lagergren pseudo-second order model best described the kinetics of adsorption of Mn2+ onto the modified palygorskites.

Use of Natural Kaolinite Clay as an Adsorbent to Remove PB(II), CD(II), and CU(II) from Aqueous Solution

2014 ◽  
Vol 805 ◽  
pp. 581-584 ◽  
Author(s):  
Débora Martins Aragão ◽  
Maria de Lara P.M. Arguelho ◽  
Carolina Mangieri Oliveira Prado ◽  
José do Patrocinio Hora Alves
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Adsorption Process ◽  
Adsorption Equilibrium ◽  
Northeast Brazil ◽  
Order Kinetic ◽  
Kaolinite Clay ◽  
Adsorption Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

Natural kaolinite clay collected in the State of Sergipe (northeast Brazil) was used as an adsorbent for the ions Pb2+, Cd2+, and Cu2+present in aqueous solution. Adsorption equilibrium was reached rapidly, enabling use of a contact time of 30 minutes, and maximum adsorption was achieved at pH 7.0. For all three metal ions, the adsorption data could be fitted using the Langmuir isotherm and the adsorption process obeyed a pseudo-second order kinetic model.

Sign in / Sign up

Export Citation Format

Share Document