Computational fluid dynamics simulations of membrane filtration process adapted for water treatment of aerated sewage lagoons

2014 ◽  
Vol 71 (2) ◽  
pp. 197-202
Author(s):  
Grégory Cano ◽  
Adil Mouahid ◽  
Emilie Carretier ◽  
Pascal Guasp ◽  
Didier Dhaler ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Rural Areas ◽  
Membrane Filtration ◽  
Numerical Models ◽  
Operating Conditions ◽  
Permeate Flux ◽  
Filtration Process ◽  
Membrane Area ◽  
Sewage Lagoons

The aim of this study is to apply the membrane bioreactor technology in an oxidation ditch in submerged conditions. This new wastewater filtration process will benefit rural areas (<5,000 population equivalent) subject to chronic water shortages by reusing this water for irrigation of green areas. For this purpose, the membranes developed without support are immersed in an aeration well and work in suction mode. The development of the membrane without support and more precisely the performance of spacers are approached by computational fluid dynamics in order to provide the best compromise between pressure drop/flow velocity and permeate flux. The numerical results on the layout and the membrane modules' geometry in the aeration well indicate that the optimal configuration is to install the membranes horizontally on three levels. Membranes should be connected to each other to a manifold providing a total membrane area of 18 m². Loss rate compared to the theoretical throughput is relatively low (less than 3%). Preliminary data obtained by modeling the lagoon provide access to its hydrodynamics, revealing that recirculation zones can be optimized by making changes in the operating conditions. The experimental validation of these results and taking into account the aeration in the numerical models are underway.

scholarly journals CFD Investigation of Trout-Like Configuration Holding Station near an Obstruction

Fluids ◽  
2021 ◽  
Vol 6 (6) ◽  
pp. 204
Author(s):  
Kamran Fouladi ◽  
David J. Coughlin
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Laboratory Experiment ◽  
Numerical Models ◽  
Interaction Model ◽  
Underwater Vehicle ◽  
Water Stream ◽  
Hydrodynamic Analysis ◽  
Structure Interaction ◽  
Vehicle Systems

This report presents the development of a fluid-structure interaction model using commercial Computational fluid dynamics software and in-house developed User Defined Function to simulate the motion of a trout Department of Mechanical Engineering, Widener University holding station in a moving water stream. The oscillation model used in this study is based on the observations of trout swimming in a respirometry tank in a laboratory experiment. The numerical simulations showed results that are consistent with laboratory observations of a trout holding station in the tank without obstruction and trout entrained to the side of the cylindrical obstruction. This paper will be helpful in the development of numerical models for the hydrodynamic analysis of bioinspired unmanned underwater vehicle systems.

Computational Fluid Dynamics Thermohydrodynamic Analysis of Three-Dimensional Sector-Pad Thrust Bearings With Rectangular Dimples

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
C. I. Papadopoulos ◽  
L. Kaiktsis ◽  
M. Fillon
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Carrying Capacity ◽  
Thermal Effects ◽  
Operating Conditions ◽  
Load Carrying Capacity ◽  
Performance Indices ◽  
Thrust Bearings ◽  
Load Carrying ◽  
Texture Design

The paper presents a detailed computational study of flow patterns and performance indices in a dimpled parallel thrust bearing. The bearing consists of eight pads; the stator surface of each pad is partially textured with rectangular dimples, aiming at maximizing the load carrying capacity. The bearing tribological performance is characterized by means of computational fluid dynamics (CFD) simulations, based on the numerical solution of the Navier–Stokes and energy equations for incompressible flow. Realistic boundary conditions are implemented. The effects of operating conditions and texture design are studied for the case of isothermal flow. First, for a reference texture pattern, the effects of varying operating conditions, in particular minimum film thickness (thrust load), rotational speed and feeding oil pressure are investigated. Next, the effects of varying texture geometry characteristics, in particular texture zone circumferential/radial extent, dimple depth, and texture density on the bearing performance indices (load carrying capacity, friction torque, and friction coefficient) are studied, for a representative operating point. For the reference texture design, the effects of varying operating conditions are further investigated, by also taking into account thermal effects. In particular, adiabatic conditions and conjugate heat transfer at the bearing pad are considered. The results of the present study indicate that parallel thrust bearings textured by proper rectangular dimples are characterized by substantial load carrying capacity levels. Thermal effects may significantly reduce load capacity, especially in the range of high speeds and high loads. Based on the present results, favorable texture designs can be assessed.

Metal Temperature Prediction of a Dry Low NOx Class Flame Tube by Computational Fluid Dynamics Conjugate Heat Transfer Approach

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Riccardo Da Soghe ◽  
Cosimo Bianchini ◽  
Antonio Andreini ◽  
Lorenzo Mazzei ◽  
Giovanni Riccio ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Operating Conditions ◽  
Metal Temperature ◽  
Thermal Loads ◽  
Flame Tube ◽  
Numerical Predictions ◽  
Partial Load ◽  
Critical Components

Combustor liner of present gas turbine engines is subjected to high thermal loads as it surrounds high temperature combustion reactants and is hence facing the related radiative load. This generally produces high thermal stress levels on the liner, strongly limiting its life expectations and making it one of the most critical components of the entire engine. The reliable prediction of such thermal loads is hence a crucial aspect to increase the flame tube life span and to ensure safe operations. The present study aims at investigating the aerothermal behavior of a GE Dry Low NOx (DLN1) class flame tube and in particular at evaluating working metal temperatures of the liner in relation to the flow and heat transfer state inside and outside the combustion chamber. Three different operating conditions have been accounted for (i.e., lean–lean partial load, premixed full load, and primary load) to determine the amount of heat transfer from the gas to the liner by means of computational fluid dynamics (CFD). The numerical predictions have been compared to experimental measurements of metal temperature showing a good agreement between CFD and experiments.

Performance Analysis of Gas-Expanded Lubricants in a Hybrid Bearing Using Computational Fluid Dynamics

2015 ◽  
Author(s):  
Brian K. Weaver ◽  
Gen Fu ◽  
Andres F. Clarens ◽  
Alexandrina Untaroiu
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Phase Behavior ◽  
Ambient Pressure ◽  
Operating Conditions ◽  
Full Potential ◽  
Dissolved Carbon ◽  
Bearing Stiffness ◽  
Multi Phase ◽  
Stiffness And Damping

Gas-expanded lubricants (GELs), tunable mixtures of synthetic oil and dissolved carbon dioxide, have been previously shown to potentially increase bearing efficiency, rotordynamic control, and long-term reliability in flooded journal bearings by controlling the properties of the lubricant in real time. Previous experimental work has established the properties of these mixtures and multiple numerical studies have predicted that GELs stand to increase the performance of flooded bearings by reducing bearing power losses and operating temperatures while also providing control over bearing stiffness and damping properties. However, to date all previous analytical studies have utilized Reynolds equation-based approaches while assuming a single-phase mixture under high-ambient pressure conditions. The potential implications of multi-phase behavior could be significant to bearing performance, therefore a more detailed study of alternative operating conditions that may include multi-phase behavior is necessary to better understanding the full potential of GELs and their effects on bearing performance. In this work, the performance of GELs in a fixed geometry journal bearing were evaluated to examine the effects of these lubricants on the fluid and bearing dynamics of the system under varying operating conditions. The bearing considered for this study was a hybrid hydrodynamic-hydrostatic bearing to allow for the study of various lubricant supply and operating conditions. A computational fluid dynamics (CFD)-based approach allowed for a detailed evaluation of the lubricant injection pathway, the flow of fluid throughout the bearing geometry, thermal behavior, and the collection of the lubricant as it exits the bearing. This also allowed for the study of the effects of the lubricant behavior on overall bearing performance.

scholarly journals Assessing the Sensitivity of Stall-Regulated Wind Turbine Power to Blade Design Using High-Fidelity Computational Fluid Dynamics

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Andrea G. Sanvito ◽  
Giacomo Persico ◽  
M. Sergio Campobasso
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Field Testing ◽  
Turbine Rotor ◽  
Operating Conditions ◽  
High Fidelity ◽  
Blade Design ◽  
Computationally Efficient ◽  
Wind Speeds ◽  
Wide Range

Abstract This study provides a novel contribution toward the establishment of a new high-fidelity simulation-based design methodology for stall-regulated horizontal axis wind turbines. The aerodynamic design of these machines is complex, due to the difficulty of reliably predicting stall onset and poststall characteristics. Low-fidelity design methods, widely used in industry, are computationally efficient, but are often affected by significant uncertainty. Conversely, Navier–Stokes computational fluid dynamics (CFD) can reduce such uncertainty, resulting in lower development costs by reducing the need of field testing of designs not fit for purpose. Here, the compressible CFD research code COSA is used to assess the performance of two alternative designs of a 13-m stall-regulated rotor over a wide range of operating conditions. Validation of the numerical methodology is based on thorough comparisons of novel simulations and measured data of the National Renewable Energy Laboratory (NREL) phase VI turbine rotor, and one of the two industrial rotor designs. An excellent agreement is found in all cases. All simulations of the two industrial rotors are time-dependent, to capture the unsteadiness associated with stall which occurs at most wind speeds. The two designs are cross-compared, with emphasis on the different stall patterns resulting from particular design choices. The key novelty of this work is the CFD-based assessment of the correlation among turbine power, blade aerodynamics, and blade design variables (airfoil geometry, blade planform, and twist) over most operational wind speeds.

scholarly journals A zonal approach for estimating pressure ratio at compressor extreme off-design conditions

2018 ◽  
Vol 20 (4) ◽  
pp. 393-404 ◽  
Author(s):  
José Galindo ◽  
Roberto Navarro ◽  
Luis Miguel García-Cuevas ◽  
Daniel Tarí ◽  
Hadi Tartoussi ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Speed ◽  
Internal Combustion Engines ◽  
Pressure Ratio ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Combustion Engines ◽  
One Dimensional ◽  
Performance Map

Zero-dimensional/one-dimensional computational fluid dynamics codes are used to simulate the performance of complete internal combustion engines. In such codes, the operation of a turbocharger compressor is usually addressed employing its performance map. However, simulation of engine transients may drive the compressor to work at operating conditions outside the region provided by the manufacturer map. Therefore, a method is required to extrapolate the performance map to extended off-design conditions. This work examines several extrapolating methods at the different off-design regions, namely, low-pressure ratio zone, low-speed zone and high-speed zone. The accuracy of the methods is assessed with the aid of compressor extreme off-design measurements. In this way, the best method is selected for each region and the manufacturer map is used in design conditions, resulting in a zonal extrapolating approach aiming to preserve accuracy. The transitions between extrapolated zones are corrected, avoiding discontinuities and instabilities.

Computational Fluid Dynamics Modeling of Gaseous Cavitation in Lubricating Vane Pumps: An Approach Based on Dimensional Analysis

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Umberto Stuppioni ◽  
Alessio Suman ◽  
Michele Pinelli ◽  
Alessandro Blum
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Dimensional Analysis ◽  
Operating Conditions ◽  
Cfd Modeling ◽  
Dynamic Features ◽  
Dynamics Modeling ◽  
Vane Pump ◽  
Numerical Predictions ◽  
Pressure Ripple

Abstract This paper addresses the problem of computational fluid dynamics (CFD) modeling of gaseous cavitation (GC) in lubricating positive-displacement pumps (PDPs). It is important for designers and analysts to predict the dynamic features of air release/dissolution processes which characterize this phenomenon, along with their effects on filling capability and noise-vibration-harshness behavior of the machine. The focus is on the empirical tuning of the commercial homogeneous-flow cavitation model known as dissolved gas model (DGM). Considering an automotive case study of a balanced vane pump (BVP), the effects of air modeling on numerical predictions of discharge flow/pressure ripple and volumetric efficiency have been studied. The tuning time parameters of the model have been correlated to the machine Reynolds number as part of a simplified theoretical background based on dimensional analysis. Considering experimental data at different operating conditions, the tuned model has shown a good capacity in predicting the pressure ripple and the flowrate at the discharge of the pump.

Circular Cylinder Exposed to Cross Flow Fluid Forces – Parameters of Influence – Limits of Numerical Models

2003 ◽  
Author(s):  
Christoph Reichel ◽  
Klaus Strohmeier
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Models ◽  
Lift Coefficient ◽  
Cross Flow ◽  
Circular Cylinders ◽  
Rigid Cylinder ◽  
Fluid Forces ◽  
Wide Range ◽  
Dynamics Simulations

In many technical fields, e.g. heat exchangers, circular cylinders are involved in Fluid Structure Interaction (FSI) problems. Therefore correct frequency and magnitude of fluid forces, respectively Strouhal number, drag and lift coefficient are needed. If fluid forces are evaluated with Computational Fluid Dynamics (CFD), mostly flow around a rigid cylinder is used to verify model and numerical methods. Unfortunately experimental as well as numerical results show great variation, making verification and testing of models difficult. Reynolds number is regarded as main influencing parameter for a rigid cylinder in cross flow. Most of experimental deviations can be related to other parameters, which differ from experiment to experiment. In this paper such parameters are specified and it is shown, that a closer look is needed, if one really wants to verify a model. Besides experimental results, which can be found in literature, some parameters are investigated by numerical simulation. Like experiments CFD (Computational Fluid Dynamics) simulations show a huge bandwidth of results, even when the same turbulence model is used. Flow around cylinders separates over a wide range of Reynolds numbers. It will be demonstrated that, using CFD, large deviations in fluid forces can often be related to miscalculation of the point of separation.

Application of computational fluid dynamics for thermohydrodynamic analysis of high-speed squeeze-film dampers

2019 ◽  
Vol 43 (3) ◽  
pp. 306-321 ◽  
Author(s):  
Maxime Perreault ◽  
Sina Hamzehlouia ◽  
Kamran Behdinan
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Speed ◽  
Operating Conditions ◽  
Squeeze Film ◽  
Radial Clearance ◽  
Base Line ◽  
Squeeze Film Dampers ◽  
Shaft Deflection ◽  
Whirl Speed

In high-speed turbomachinery, the presence of rotor vibrations, which produce undesirable noise or shaft deflection and losses in performance, has brought up the need for the application of a proper mechanism to attenuate the vibration amplitudes. Squeeze-film dampers (SFDs) are a widely employed solution to the steady-state vibrations in high-speed turbomachinery. SFDs contain a thin film of lubricant that is susceptible to changes in temperature. For this reason, the analysis of thermohydrodynamic (THD) effects on the SFD damping properties is essential. This paper develops a computational fluid dynamics (CFD) model to analyze the THD effects in SFDs, and enabling the application of CFD analysis to be a base-line for validating the accuracy of analytical THD SFD models. Specifically, the CFD results are compared against numerical simulations at different operating conditions, including eccentricity ratios and journal whirl speeds. The comparisons demonstrate the effective application of CFD for THD analysis of SFDs. Additionally, the effect of the lubricant THDs on the viscosity, maximum and mass-averaged temperature, as well as heat generation rates inside the SFD lubricant are analyzed. The temperature of the lubricant is seen to rise with increasing whirl speed, eccentricity ratios, damper radial clearance, and shaft radii.

Sign in / Sign up

Export Citation Format

Share Document