scholarly journals Treatment of folic acid wastewater by 3D Fe-N-TiO2/AC photoelectrocatalysis system

2019 ◽  
Vol 80 (10) ◽  
pp. 1919-1930
Author(s):  
Junwo Zhou ◽  
Zhen Zhou ◽  
Yong Gao ◽  
Tingting Li ◽  
Manying Zhang ◽  
...  
Keyword(s):  
Folic Acid ◽  
Ph Value ◽  
Synergistic Effects ◽  
Three Dimensional ◽  
Degradation Process ◽  
Film Coating ◽  
Order Kinetic ◽  
Mechanism Study ◽  
Cellulose Acetate Film ◽  
Toc Removal

Abstract In this work, particles of activated carbon supported by Fe-N-TiO2 (Fe-N-TiO2/AC) were synthesized and used as the three-dimensional (3D) particle electrode for folic acid wastewater treatment in the 3D electrolysis and photocatalysis coupling process. The structure, morphology, and physical and electrochemical properties of the Fe-N-TiO2/AC particles were characterized, and the results showed that Fe-N-TiO2 was bound on the surface of AC particles by chemical attachment, and the Fe-N-TiO2/AC particles had better capability of adsorption and charge transfer as compared with the TiO2/AC particles. The effects of key operating parameters in the reaction process, including the current density (optimum 0.6 mA/cm2), aeration (optimum 5 L/min), pH value (optimum 5) and the ratio of Fe-N-TiO2/AC particles to cellulose acetate film coating AC particles (optimum 4:1), were optimized regarding the total oxygen carbon (TOC) removal. Under the optimum conditions, TOC removal from folic acid wastewater reached 82.4% during 120 min photoelectrocatalysis. The kinetic analysis and mechanism study showed that the degradation process fitted to the second-order kinetic model better than to the first-order, and the system exhibited synergistic effects in inhibiting photogenic electron–hole recombination and improving electrolytic efficiency. At the same time, this system has the ability to overcome the interference of the strong ionic strength in folic acid wastewater.

scholarly journals Enhanced removal of ibuprofen by heterogeneous photo-Fenton like process over sludge based Fe3O4-MnO2 catalysts

2021 ◽  
Author(s):  
Yanjun Liu ◽  
Xiaoqian Zheng ◽  
Shufen Zhang ◽  
Shujuan Sun
Keyword(s):  
Catalytic Mechanism ◽  
Ph Value ◽  
Low Cost ◽  
Degradation Process ◽  
Hydroxyl Groups ◽  
Order Kinetic ◽  
Product Analysis ◽  
Experimental Conditions ◽  
Preparation Conditions ◽  
Nano Fe3o4

Abstract Heterogeneous photo-Fenton like catalysts with low cost, little hazardous, high effective and facile separation from aqueous solution were highly desirable. In this study, sludge-based catalysts combining nano Fe3O4-MnO2 and sludge activated carbon were successfully synthesized by high-temperature calcination method and then characterized. These synthetic materials were applied to remove ibuprofen in the heterogeneous photo-Fenton process. The preparation conditions of sludge-based catalysts optimized by orthogonal experiments were 2.0 M of ZnCl2, a temperature of 500 °C, a pyrolysis time of 60 min, and a sludge ratio: Fe3O4-MnO2 of 25:2. In batch experiments, the optimal experimental conditions were determined as catalyst dosage of 0.4 g·L−1, hydrogen peroxide concentration of 3.0 g·L−1, pH value of 3.3, and contact time of 2.5 h. The degradation rate Sludge/Fe3O4-MnO2 catalyst to ibuprofen is up to 95%. The removal process of ibuprofen fitted the pseudo-second-order kinetic model, and the photocatalytic degradation process was the main factor controlling the reaction rate. The catalytic mechanism was proposed according to the FTIR analysis and mass spectrometry product analysis, it was mainly attributed to the interaction between hydroxyl groups and benzene rings.

scholarly journals Thermally activated persulfate treatment and mineralization of a recalcitrant high TDS petrochemical wastewater

2017 ◽  
Vol 19 (2) ◽  
pp. 72-77 ◽  
Author(s):  
Sahand Jorfi ◽  
Sudabeh Pourfadakari ◽  
Mehdi Ahmadi ◽  
Hamideh Akbari
Keyword(s):  
Ph Value ◽  
Cod Removal ◽  
Order Kinetic ◽  
Operational Parameters ◽  
Batch Mode ◽  
Thermally Activated ◽  
Toc Removal ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
Activated Persulfate

Abstract Thermally activated persulfate efficiency for the treatment of a recalcitrant high TDS wastewater was investigated. The specific character of studied wastewater was high TDS content of around 23820 mg/L and BOD5/COD ratio of 0.07. Effective operational parameters including initial pH values of 3–9, reaction temperature of 40–80°C and persulfate concentrations of 0.5–5 g/L for COD removal were investigated in batch mode experiments. Removal efficiency was pH and temperature dependent. The COD and TOC removal of 94.3% and 82.8% were obtained at persulfate concentration of 4 g/L, initial pH value of 5 and temperature of 70°C after 180 min for initial COD concentration of 1410 mg/L. The pseudo first-order kinetic model was best fitted with COD removal (R2 = 0.94).

Ferrate(VI): a novel oxidant for degradation of cationic surfactant – cetylpyridinium bromide

2013 ◽  
Vol 67 (10) ◽  
pp. 2184-2189 ◽  
Author(s):  
Weihua Yang ◽  
Xiaoyan Lin ◽  
Honghui Wang ◽  
Wutao Yang
Keyword(s):  
Reaction Time ◽  
Organic Carbon ◽  
Cationic Surfactants ◽  
Degradation Process ◽  
Order Kinetic ◽  
Cetylpyridinium Bromide ◽  
Operating Variables ◽  
Toc Removal ◽  
Treatment Conditions ◽  
Initial Ph

Ferrate(VI) is an efficient multi-functional water treatment reagent that has several novel properties, such as strong oxidation, absorption, flocculation, disinfection and deodorization. The removal of cationic surfactants based on ferrate (K2FeO4) was performed in the case of cetylpyridinium bromide (CPB). The influence of operating variables on the mineralization efficiency was studied as a function of ferrate dosage, initial pH and reaction time. Total organic carbon (TOC), UV and infrared spectra were performed to gain a better understanding of the degradation process. Results show that the optimal treatment conditions are as follows, solution initial pH is over 5, oxidation time is 5 min and ferrate dosage is 1.5 times that of CPB. The removal efficiency of CPB above 99% and TOC removal percentage of 91.3% can be achieved in minutes. The reaction of CPB with K2FeO4 responds to a second-order kinetic law.

scholarly journals Degradation of folic acid wastewater by electro-Fenton with three-dimensional electrode and its kinetic study

2018 ◽  
Vol 5 (1) ◽  
pp. 170926 ◽  
Author(s):  
Gu Xiaochao ◽  
Lu Xuebin ◽  
Tian Jin ◽  
Li Xiaoyun ◽  
Zhou Bin ◽  
...  
Keyword(s):  
Folic Acid ◽  
Reaction Time ◽  
Current Density ◽  
Three Dimensional ◽  
Oxygen Demand ◽  
Degradation Process ◽  
Kinetics Analysis ◽  
Acid Decomposition ◽  
Reaction Conditions ◽  
Optimal Reaction

The three-dimensional electro-Fenton method was used in the folic acid wastewater pretreatment process. In this study, we researched the degradation of folic acid and the effects of different parameters such as the air sparging rate, current density, pH and reaction time on chemical oxygen demand (COD) removal in folic acid wastewater. A four-level and four-factor orthogonal test was designed and optimal reaction conditions to pretreat folic acid wastewater by three-dimensional electrode were determined: air sparge rate 0.75 l min −1 , current density 10.26 mA cm −2 , pH 5 and reaction time 90 min. Under these conditions, the removal of COD reached 94.87%. LC-MS results showed that the electro-Fenton method led to an initial folic acid decomposition into p -aminobenzoyl-glutamic acid (PGA) and xanthopterin (XA); then part of the XA was oxidized to pterine-6-carboxylic acid (PCA) and the remaining part of XA was converted to pterin and carbon dioxide. The kinetics analysis of the folic acid degradation process during pretreatment was carried out by using simulated folic acid wastewater, and it could be proved that the degradation of folic acid by using the three-dimensional electro-Fenton method was a second-order reaction process. This study provided a reference for industrial folic acid treatment.

Kinetic and thermodynamic study of the adsorption of calcium onto sugar beet pulp

2016 ◽  
pp. 565-570
Author(s):  
Huang Qin ◽  
Zhu Si-ming ◽  
Zeng Di ◽  
Yu Shu-juan
Keyword(s):  
Sugar Beet ◽  
Adsorption Equilibrium ◽  
Ph Value ◽  
Hard Water ◽  
Sugar Beet Pulp ◽  
Order Kinetic ◽  
Factors Affecting ◽  
Isotherm Equation ◽  
Equilibrium Data ◽  
Beet Pulp

Sugar beet pulp (SBP) was used as low value adsorbent for the removal of calcium from hard water. Batch experiments were conducted to determine the factors affecting adsorption of the process such as pH value and Ca concentration. The adsorption equilibrium of Ca2+ by the SBP is reached after 100min and a pseudo second-order kinetic model can describe the adsorption process. The initial concentrations of Ca varied from 927 to 1127mgCa2+/L. A dose of 30g/L sugar beet pulp was sufficient for the optimum removal of calcium. The overall uptake of Ca ions by sugar beet pulp has its maximum at pH=8. The adsorption equilibrium data fitted well with the Langmuir adsorption isotherm equation.

Nano-ZrO2/TiO2 Impregnated Orange Wood Sawdust and Peach Stone Shell Adsorbents for Cr (VI) Removal

2020 ◽  
Vol 16 (7) ◽  
pp. 880-892
Author(s):  
Şerife Parlayıcı ◽  
Kübra Tuna Sezer ◽  
Erol Pehlivan
Keyword(s):  
Contact Time ◽  
Ph Value ◽  
Order Kinetic ◽  
Adsorption Parameters ◽  
Wood Sawdust ◽  
Adsorption Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Equilibrium Status

Background: In this work, Cr (VI) adsorption on nano-ZrO2๏TiO2 impregnated orange wood sawdust (Zr๏Ti/OWS) and nano-ZrO2๏TiO2 impregnated peach stone shell (Zr๏Ti/PSS) was investigated by applying different adsorption parameters such as Cr (VI) concentrations, contact time, adsorbent dose, and pH for all adsorbents. Methods: The adsorbents were characterized by SEM and FT-IR. The equilibrium status was achieved after 120 min of contact time and optimum pH value around 2 were determined for Cr (VI) adsorption. Adsorption data in the equilibrium is well-assembled by the Langmuir model during the adsorption process. Results: Langmuir isotherm model showed a maximum adsorption value of OWS: 21.65 mg/g and Zr๏Ti/OWS: 27.25 mg/g. The same isotherm displayed a maximum adsorption value of PSS: 17.64 mg/g, and Zr๏Ti/PSS: 31.15 mg/g. Pseudo-second-order kinetic models (R2=0.99) were found to be the best models for describing the Cr (VI) adsorption reactions. Conclusıon: Thermodynamic parameters such as changes in ΔG°, ΔH°, and ΔS° have been estimated, and the process was found to be spontaneous.

Adsorption Characteristics of Phenol in Aqueous Solution by Pinus massoniana Biochar

2013 ◽  
Vol 295-298 ◽  
pp. 1154-1160 ◽  
Author(s):  
Guo Zhi Deng ◽  
Xue Yuan Wang ◽  
Xian Yang Shi ◽  
Qian Qian Hong
Keyword(s):  
Aqueous Solution ◽  
Ph Value ◽  
Pinus Massoniana ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Adsorbent Dosage ◽  
Salt Ions ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The objective of this paper is to investigate the feasibility of phenol adsorption from aqueous solution by Pinus massoniana biochar. Adsorption conditions, including contact time, initial phenol concentration, adsorbent dosage, strength of salt ions and pH, have been investigated by batch experiments. Equilibrium can be reached in 24 h for phenol from 50 to 250 mg• L-1. The optimum pH value for this kind of biochar is 5.0. The amount of phenol adsorbed per unit decreases with the increase in adsorbent dosage. The existence of salt ions makes negligible influence on the equilibrium adsorption capacity. The experimental data is analyzed by the Freundlich and Langmuir isotherm models. Equilibrium data fits well to the Freundlich model. Adsorption kinetics models are deduced and the pseudo-second-order kinetic model provides a good correlation for the adsorbent process. The results show that the Pinus massoniana biochar can be utilized as an effective adsorption material for the removal of phenol from aqueous solution.

scholarly journals The sorption of inorganic arsenic on modified sepiolite: Effect of hydrated iron(III)-oxide

2014 ◽  
Vol 79 (7) ◽  
pp. 815-828 ◽  
Author(s):  
Nikola Ilic ◽  
Slavica Lazarevic ◽  
Vladana Rajakovic-Ognjanovic ◽  
Ljubinka Rajakovic ◽  
Djordje Janackovic ◽  
...  
Keyword(s):  
Sorption Capacity ◽  
Arsenic Removal ◽  
Ph Value ◽  
Inorganic Arsenic ◽  
Arsenic Species ◽  
Deionized Water ◽  
Order Kinetic ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The sorption of inorganic arsenic species, As(III) and As(V), from water by sepiolite modified with hydrated iron(III) oxide was investigated at 25 ?C through batch studies. The influence of the initial pH value, the initial As concentrations, the contact time and types of water on the sorption capacity was investigated. Two types of water were used, deionized and groundwater. The maximal sorption capacity for As(III) from deionized water was observed at initial and final pH value 7.0, while the bonding of As(V) was observed to be almost pH independent for pH value in the range from 2.0 to 7.0, and the significant decrease in the sorption capacity was observed at pH values above 7.0. The sorption capacity at initial pH 7.0 was about 10 mg g?1 for As(III) and 4.2 mg g?1 for As(V) in deionized water. The capacity in groundwater was decreased by 40 % for As(III) and by 20 % for As(V). The Langmuir model and pseudo-second order kinetic model revealed good agreement with the experimental results. The results show that Fe(III)-modified sepiolite exhibits significant affinity for arsenic removal and it has a potential for the application in water purification processes.

scholarly journals Lignocellulose@ Activated Clay Nanocomposite with Hierarchical Nanostructure Enhancing the Removal of Aqueous Zn(II)

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1710 ◽  
Author(s):  
Xiaotao Zhang ◽  
Yinan Hao ◽  
Zhangjing Chen ◽  
Yuhong An ◽  
Wanqi Zhang ◽  
...  
Keyword(s):  
Ph Value ◽  
Removal Rate ◽  
Weight Ratio ◽  
Order Kinetic ◽  
Adsorption Parameters ◽  
Hierarchical Nanostructure ◽  
Desorption Temperature ◽  
Desorption Time ◽  
Adsorption Temperature ◽  
Hcl Concentration

A lignocellulose@ activated clay (Ln@AC) nanocomposite with a hierarchical nanostructure was successfully synthesized by the chemical intercalation reaction and applied in the removal of Zn(II) from an aqueous solution. Ln@AC was characterized by N2 adsorption/desorption isotherms and X-Ray Diffraction (XRD), scanning Electron Microscope (SEM), transmission Electron Microscopy (TEM) and Fourier Transform Infrared Spectroscopy (FTIR) analysis, and the results indicate that an intercalated–exfoliated hierarchical nanostructure was formed. The effects of different adsorption parameters on the Zn(II) removal rate (weight ratio of Ln to AC, Ln@AC dosage, initial Zn(II) concentration, pH value, adsorption temperature, and time) were investigated in detail. The equilibrium adsorption capacity reached 315.9 mg/g under optimal conditions (i.e., the weight ratio of Ln to AC of 3:1, Ln@AC dosage of 1 g/L, initial Zn(II) concentration of 600 mg/L, pH value of 6.8, adsorption temperature of 65 °C, and adsorption time of 50 min). The adsorption process was described by the pseudo-second-order kinetic model, Langmuir isotherm model, and the Elovich model. Moreover, Zn(II) could be easily eluted by HCl, and the effects of HCl concentration, desorption temperature, and ultrasonic desorption time on desorbed amount were tested. Desorption studies revealed that with an HCl concentration of 0.25 mol/L, desorption temperature of 70 °C, and ultrasonic desorption time of 20 min, the maximum desorption capacity and efficiency were achieved at 202.5 mg/g and 64.10%, respectively. Regeneration experimental results indicated that the Ln@AC exhibited a certain recyclable regeneration performance. Due to such outstanding features, the novel Ln@AC nanocomposite proved to have great adsorption potential for Zn(II) removal from wastewater, and exhibited an extremely significant amount of adsorbed Zn(II) when compared to conventional adsorbents.

scholarly journals Strategically prolonged release of multiple antibacterial components from a thin film coating for synergistic effects against Staphylococcus aureus infections

RSC Advances ◽  
2019 ◽  
Vol 9 (56) ◽  
pp. 32683-32690 ◽  
Author(s):  
Meijun Song ◽  
Haidong Zhu ◽  
Lin Ye ◽  
Chengxiang Liu ◽  
Zhaojun Xu
Keyword(s):  
Thin Film ◽  
Staphylococcus Aureus ◽  
Synergistic Effects ◽  
Film Coating ◽  
Prolonged Release ◽  
Thin Film Coating

Biomaterial-associated infections (BAIs) remain a major challenge in clinical surgery because they can potentially cause serious disabilities in patients.

Sign in / Sign up

Export Citation Format

Share Document