scholarly journals Evaluation of Pb (II) Adsorption from Aqueous Solutions Using Brassica nigra as a Biosorbent

2019 ◽  
Vol 13 (1) ◽  
pp. 77-92 ◽  
Author(s):  
Warren Reátegui-Romero ◽  
Walter J. Cadenas-Vásquez ◽  
María E. King-Santos ◽  
Walter F. Zaldivar Alvarez ◽  
Ricardo A. Y. Posadas
Keyword(s):  
Particle Size ◽  
Aqueous Solutions ◽  
Freundlich Isotherm ◽  
Brassica Nigra ◽  
Second Order ◽  
Lead Ion ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Operating Variables

Objectives: The Pb non-biodegradability results in bioaccumulation in living organisms causing serious health disorders. The present study aimed to investigate the capacity of Pb (II) adsorption in aqueous solutions using the Brassica nigra species as biosorbent. Methods: The present study was conducted using a synthetic solution with three Pb (II) concentrations (5, 15, and 30 ppm). The B. nigra was suitably treated until it became dry particles. After sifting it, three ranges of grain sizes were obtained. Samples of dry particles were analyzed before and after the biosorption to analyze their topography (SEM), as well as the elements on their surface (EDS). The influence of different operating variables on the biosorption of Pb (II) were analyzed. Kinetics of Pb (II) biosorption was analyzed with pseudo first and second order models. The biosorption in the equilibrium was studied with the Langmuir isotherm and Freundlich isotherm models. Results: The biosorbent B. nigra showed to be efficient for the adsorption of Pb (II). The most influential variables in the adsorption were pH, particle size, and biosorbent/solution ratio. The optimum pH for the adsorption of lead was 5 and removed 82.10% of lead from solution at 5 ppm, 82.24% at 15 ppm and 57.95% at 30 ppm. The results for the particle size between 177 and 297 μm were 82.65% for 5 ppm, 73.71% for 15 ppm, and 53.54% for 30 ppm. The biosorbent/solution ratio of 0.6 mg/mL or the 30 mg dose of biosorbent removed 80.26% for 5 ppm, 79.32% for 15 ppm, and 59.87% for 30 ppm. Biosorption isothermal data could be well interpreted by the Langmuir model with a maximum adsorption capacity of 53.476 mg/g of lead ion on B. nigra stem and roots biomass. The kinetic experimental data was properly correlated with the second-order kinetic model (R2 = 0.9997). Thus, the best desorbing agent was HNO3 (0.1N) for Pb (II) desorption. Conclusion: Our study showed that the herb B. nigra, without any chemical treatment, can be used to remove heavy metals such as Pb (II) from water and aqueous solution.

Kinetics of lead ion biosorption from aqueous solution onto lyophilized Aspergillus niveus

2010 ◽  
Vol 5 (1) ◽  
Author(s):  
Hülya Karaca ◽  
Turgay Tay ◽  
Merih Kıvanç
Keyword(s):  
Adsorption Capacity ◽  
Correlation Coefficients ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Lead Ions ◽  
Lead Ion ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Aspergillus Niveus ◽  
Pseudo Second Order

The biosorption of lead ions (Pb2+) onto lyophilized fungus Aspergillus niveus was investigated in aqueous solutions in a batch system with respect to pH, contact time and initial concentration of the ions at 30 °C. The maximum adsorption capacity of lyophilized A. niveus was found to be 92.6 mg g−1 at pH 5.1 and the biosorption equilibrium was established about in 30 min. The adsorption capacity obtained is one of the highest value among those reported in the literature. The kinetic data were analyzed using the pseudo-first-order kinetic, pseudo-second-order kinetic, and intraparticle diffusion equations. Kinetic parameters, such as rate constants, equilibrium adsorption capacities, and related correlation coefficients for the kinetic models were calculated and discussed. It was found that the adsorption of lead ions onto lyophilized A. niveus biomass fit the pseudo-second-order kinetic model well. The Langmuir and Freundlich isotherm parameters for the lead ion adsorption were applied and the Langmuir model agreed better with the adsorption of lead ions onto lyophilized A. niveus.

scholarly journals Removal of Zinc from Aqueous Solutions by Magnetite Silica Core-Shell Nanoparticles

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Masoomeh Emadi ◽  
Esmaeil Shams ◽  
Mohammad Kazem Amini
Keyword(s):  
Aqueous Solutions ◽  
Sol Gel ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Core Shell ◽  
Order Kinetic ◽  
Shell Nanoparticles ◽  
Silica Core ◽  
Core Shell Nanoparticles

Magnetite silica core-shell nanoparticles (Fe3O4-SiO2) were synthesized and evaluated as a nanoadsorbent for removing Zn(II) from aqueous solutions. The core-shell nanoparticles were prepared by combining coprecipitation and sol-gel methods. Nanoparticles were characterized by X-ray diffraction, transmission electron microscopy (TEM), and FT-IR. The magnetization values of nanoparticles were measured with vibrating sample magnetometer (VSM). The adsorption of Zn(II) ions was examined by batch equilibrium technique. The effects of pH, initial Zn(II) concentration, and contact time on the efficiency of Zn(II) removal were studied. The equilibrium data, analyzed by using Langmuir and Freundlich isotherm models, showed better agreement with the former model. Using the Langmuir isotherm model, maximum capacity of the nanoadsorbent for Zn(II) was found to be 119 mg g−1at room temperature. Kinetic studies were conducted and the resulting data were analyzed using first- and second-order equations; pseudo-second-order kinetic equation was found to provide the best correlation. The adsorption and sedimentation times were very low. The nanoadsorbent can be easily separated from aqueous solution by a magnet. Repeated adsorption acid regeneration cycles were performed to examine the stability and reusability of the nanoadsorbent. The result of this study proved high stability and reusability of Fe3O4-SiO2as an adsorbent for Zn(II) ions.

scholarly journals ADSORPTION OF FOOD COLORING ALLURA RED DYE (E129) FROM AQUEOUS SOLUTIONS USING ACTIVATED CARBON

2017 ◽  
Vol 3 (1) ◽  
pp. 10 ◽  
Author(s):  
Saad A Alkahtani ◽  
Samer S Abu-Alrub ◽  
Ashraf M Mahmoud
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Kinetic Models ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Factors Affecting ◽  
Allura Red

<p>The adsorption behavior of Allura red (E129)<strong> </strong>from aqueous solutions onto activated carbon was successfully investigated. All factors affecting the adsorption process were carefully studied and the conditions were optimized. Adsorption of E129 onto activated carbon was found to increase by decreasing the mass of activated carbon, pH and ionic strength of the solution and by increasing temperature. The adsorption capacity of the activated carbon for Allura red was relatively high. Under the optimum conditions, the maximum adsorption capacity for E129 dye was 72.85 mg/g. Three adsorption models; Langmuir, Freundlich and Temkin model were investigated regarding the adsorption of E129. The models’ parameters K<sub>L</sub>, qm, R2, (n) were determined and found to be 0.0222, 72.85 mg/g, 0.9057-0.9984, and 0.992, respectively. Also, pseudo first and second-order kinetic models were tested to determine the best-fit model to the adsorption of E129 dye onto activated carbon. The results showed that the adsorption of E129 onto activated carbon obeyed both the Freundlich isotherm and pseudo second-order kinetic models. Moreover, thermodynamic studies indicated that the adsorption of E129 dye onto the activated carbon was spontaneous. </p>

scholarly journals Adsorption of Phenol on Commercial Activated Carbons: Modelling and Interpretation

2020 ◽  
Vol 17 (3) ◽  
pp. 789 ◽  
Author(s):  
Bingxin Xie ◽  
Jihong Qin ◽  
Shu Wang ◽  
Xin Li ◽  
Hui Sun ◽  
...  
Keyword(s):  
Experimental Data ◽  
Activated Carbons ◽  
Freundlich Isotherm ◽  
Mesoporous Structure ◽  
Second Order ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Phenol Removal ◽  
Order Kinetic ◽  
Pseudo Second Order

Adsorption by activated carbons (AC) is an effective option for phenolic wastewater treatment. Three commercial AC, including coal-derived granular activated carbons (GAC950), coal-derived powdered activated carbons (PAC800), and coconut shell-derived powdered activated carbons (PAC1000), were utilized as adsorbent to study its viability and efficiency for phenol removal from wastewater. Pseudo-first order, pseudo-second order, and the Weber–Morris kinetic models were used to find out the kinetic parameters and mechanism of adsorption process. Further, to describe the equilibrium isotherms, the experimental data were analyzed by the Langmuir and Freundlich isotherm models. According to the experimental results, AC presented a micro/mesoporous structure, and the removal of phenol by AC was affected by initial phenol concentration, contact time, pH, temperature, and humic acid (HA) concentration. The pseudo-second order kinetic and Langmuir models were found to fit the experimental data very well, and the maximum adsorption capacity was 169.91, 176.58, and 212.96 mg/g for GAC950, PAC800, and PAC1000, respectively, which was attributed to differences in their precursors and physical appearance. Finally, it was hard for phenol to be desorbed in a natural environment, which confirmed that commercial AC are effective adsorbents for phenol removal from effluent wastewater.

Adsorption of Congo Red Dye from Aqueous Solutions by Montmorillonite as a Low-cost Adsorbent

2017 ◽  
Vol 16 (1) ◽  
Author(s):  
Yusef Omidi Khaniabadi ◽  
Hassan Basiri ◽  
Heshmatollah Nourmoradi ◽  
Mohammad Javad Mohammadi ◽  
Ahmad Reza Yari ◽  
...  
Keyword(s):  
Aqueous Solutions ◽  
Congo Red ◽  
Low Cost ◽  
Aqueous Media ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Effective Option ◽  
Pseudo Second Order

AbstractIn this study, the sorption of Congo red (CR), as a toxic dye, from aqueous media was investigated using montmorillonite (MMT) as a low-cost adsorbent. The influence of several factors such as contact time, pH, adsorbent dosage, dye content, and ionic strength was investigated on the dye removal. MMT was characterized by Fourier transformed infrared (FTIR) spectroscopy and X-ray diffractometer (XRD). Different kinetic and isotherm models including pseudo-first and pseudo-second order kinetic and Langmuir and Freundlich were applied to analyze experimental data, respectively. The results showed that the data were well fitted by pseudo-second-order kinetic and Freundlich isotherm models. The optimum conditions for the sorption of CR were achieved over 40 min and at pH=2. According to the results of the present study, MMT can be used as a low-cost, eco-friendly and effective option for the adsorption of CR from aqueous solutions.

scholarly journals Phenol adsorption from wastewater using cashew nut shells as adsorbent

2018 ◽  
Vol 7 (3) ◽  
pp. 966
Author(s):  
Kartik Kulkarni ◽  
Varsha Sudheer ◽  
C R Girish
Keyword(s):  
Agricultural Waste ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Multilayer Adsorption ◽  
Phenol Adsorption ◽  
Cashew Nut ◽  
Experimental Parameters ◽  
Order Kinetic Model

The potential of agricultural waste cashew nut shells as an adsorbent for removing phenol from wastewater is presented in this paper. The adsorbent was treated with 3M sulphuric acid in order to improve the properties. The experimental parameters such as adsorbent dosage, concentration and temperature were optimized with response surface methodology (RSM). The isotherm data were tested with different isotherm models and it obeyed Freundlich Isotherm showing the multilayer adsorption. The kinetic data satisfied pseudo-first order kinetic model. The maximum adsorption capacity was calculated to be 35.08 mg/g proving the capability of cashew nut shells for removing phenol from wastewater.  

scholarly journals Multi-Component Adsorption of Benzene, Toluene, Ethylbenzene, and Xylene from Aqueous Solutions by Montmorillonite Modified with Tetradecyl Trimethyl Ammonium Bromide

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
H. Nourmoradi ◽  
Mehdi Khiadani ◽  
M. Nikaeen
Keyword(s):  
Experimental Data ◽  
Aqueous Solutions ◽  
Structural Changes ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Ammonium Bromide ◽  
Order Kinetic ◽  
Multicomponent Adsorption ◽  
Benzene Toluene ◽  
Kinetic And Isotherm Models

Multicomponent adsorption of benzene, toluene, ethylbenzene, and xylene (BTEX) was assessed in aqueous solutions by montmorillonite modified with tetradecyl trimethyl ammonium bromide (TTAB-Mt). Batch experiments were conducted to determine the influences of parameters including loading rates of surfactant, contact time, pH, adsorbate concentration, and temperature on the adsorption efficiency. Scanning electron microscope (SEM) and X-ray diffractometer (XRD) were used to determine the adsorbent properties. Results showed that the modification of the adsorbent via the surfactant causes structural changes of the adsorbent. It was found that the optimum adsorption condition achieves with the surfactant loading rate of 200% of the cation exchange capacity (CEC) of the adsorbent for a period of 24 h. The sorption of BTEX by TTAB-Mt was in the order ofB<T<E<X. The experimental data were fitted by many kinetic and isotherm models. The results also showed that the pseudo-second-order kinetic model and Freundlich isotherm model could, respectively, be fitted to the experimental data better than other available kinetic and isotherm models. The thermodynamic study indicated that the sorption of BTEX with TTAB-Mt was achieved spontaneously and the adsorption process was endothermic as well as physical in nature. The regeneration results of the adsorbent also showed that the adsorption capacity of adsorbent after one use was 51% to 70% of original TTAB-Mt.

scholarly journals Removal of Cu(II) from Aqueous Solutions Using Amine-Doped Polyacrylonitrile Fibers

2020 ◽  
Vol 10 (5) ◽  
pp. 1738
Author(s):  
Kay Thwe Aung ◽  
Seung-Hee Hong ◽  
Seong-Jik Park ◽  
Chang-Gu Lee
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Equilibrium Studies ◽  
Naoh Solution ◽  
Surface Modified ◽  
Pan Fibers

Polyacrylonitrile (PAN) fibers were prepared via electrospinning and were modified with diethylenetriamine (DETA) to fabricate surface-modified PAN fibers. The surface-modified PAN fibers were used to evaluate their adsorption capacity for the removal of Cu(II) from aqueous solutions. Batch adsorption experiments were performed to examine the effects of the modification process, initial concentration, initial pH, and adsorbent dose on the adsorption of Cu(II). Kinetic analysis revealed that the experimental data fitted the pseudo-second-order kinetic model better than the pseudo-first-order model. Adsorption equilibrium studies were conducted using the Freundlich and Langmuir isotherm models, and the findings indicated that the PAN fibers modified with 85% DETA presented the highest adsorption capacity for Cu(II) of all analyzed samples. Moreover, the results revealed that the Freundlich model was more appropriate than the Langmuir one for describing the adsorption of Cu(II) onto the modified fibers at various initial Cu(II) concentrations. The maximum adsorption capacity was determined to be 87.77 mg/g at pH 4, and the percent removal of Cu(II) increased as the amount of adsorbent increased. Furthermore, the surface-modified PAN fibers could be easily regenerated using NaOH solution. Therefore, surface-modified PAN fibers could be used as adsorbents for the removal of Cu(II) from aqueous solutions.

Removal of acetaminophen (ACT) from aqueous solution by using nanosilica adsorbent: experimental study, kinetic and isotherm modeling

2020 ◽  
Vol 49 (1) ◽  
pp. 55-62
Author(s):  
Akbar Eslami ◽  
Zahra Goodarzvand Chegini ◽  
Maryam Khashij ◽  
Mohammad Mehralian ◽  
Marjan Hashemi
Keyword(s):  
Removal Rate ◽  
Synthesis Method ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Content Type ◽  
Bet Analysis ◽  
Pseudo Second Order

Purpose A nanosilica adsorbent was prepared and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and BET. Design/methodology/approach The optimum conditions for the highest adsorption performance were determined by kinetic modeling. The adsorbent was used for the adsorption of acetaminophen (ACT), and the parameters affecting the adsorption were discussed like pH, initial concentration, contact time and adsorbent dosage. The adsorbent have been characterized by SEM, XRD and BET analysis. The kinetic models including pseudo-first-order and pseudo-second-order with Langmuir and Freundlich isotherm models were applied to investigate the kinetic and isotherms parameters. Findings The adsorption of ACT increased to around 95% with the increase of nanosilica concentration to 30 g/L. Moreover, the adsorption process of ACT follows the pseudo-second-order kinetics and the Langmuir isotherm with the maximum adsorption capacity of 609 mg/g. Practical implications This study provided a simple and effective way to prepare of nanoadsorbents. This way was conductive to protect environmental and subsequent application for removal of emerging pollutants from aqueous solutions. Originality/value The novelty of the study is synthesizing the morphological and structural properties of nanosilica-based adsorbent (specific surface area, pore volume and size, shape and capability) and improving its removal rate through optimizing the synthesis method; and studying the capability of synthesis of nanosilica-based adsorbent for removal of ACT as a main emerging pharmaceutical water contaminant.

scholarly journals Parametric, equilibrium and kinetic studies on the removal of mercury using ion exchange resin

2017 ◽  
Vol 12 (2) ◽  
pp. 305-313 ◽  
Author(s):  
N. Rajamohan ◽  
M. Rajasimman
Keyword(s):  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Strong Acid ◽  
Ion Exchange Resin ◽  
Second Order ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Acid Cation ◽  
Pseudo Second Order ◽  
Langmuir Constants

This experimental research was an investigation into removal of mercury by using a strong acid cation resin, 001 × 7. Parametric experiments were conducted to determine the optimum pH, resin dosage, agitation speed and the effect of change in concentration in the range of 50–200 mg/L. High resin dosages favoured better removal efficiency but resulted in lower uptakes. Equilibrium experiments were performed and fitted to Langmuir and Freundlich isotherm models. Langmuir model suited well to this study confirming the homogeneity of the resin surface. The Langmuir constants were estimated as qmax = 110.619 mg/g and KL = 0.070 L/g at 308 K. Kinetic experiments were modeled using Pseudo second order model and higher values of R2 (&gt;0.97) were obtained. The Pseudo second order kinetic constants, namely, equilibrium uptake (qe) and rate constant (k2), were evaluated as 59.17 mg/g and 40.2 × 10−4 g mg−1 min−1 at an initial mercury concentration of 100 mg/L and temperature of 308 K.

Sign in / Sign up

Export Citation Format

Share Document