scholarly journals Effect of Iron Filings on the Mechanical Properties of Different Types of Sustainable Concrete

2018 ◽  
Vol 12 (1) ◽  
pp. 441-457 ◽  
Author(s):  
Sahar Jabbar Alserai ◽  
Wissam Kadhim Alsaraj ◽  
Zina Waleed Abass
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Indirect Tensile Strength ◽  
Recycled Aggregate ◽  
Geopolymer Concrete ◽  
Normal Concrete ◽  
Natural Aggregate ◽  
Indirect Tensile

Introduction:One of Iraq’s major environmental problems is a large amount of residual iron produced by the industrial sector, which is stored in domestic waste and landfills. The reuse of construction waste gives two aims, the first is to remove large quantities of pollution resulted from these waste, the second provides cheap resources for concrete aggregates.Methods:This study conducted a series of experiments and tests to test the feasibility of reusing this iron slag and recycled concrete aggregate in concrete mixtures. Different percentages of iron filings were used in the concrete mixture at 0, 0.5%, 0.75% and 1%. Tests are done to evaluate the quality of cast iron concrete which include compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) for four sustainable concretes.Results and Conclusion:The results show that the iron filings amount is increased to 1.0% which resulted in increasing percentage of compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) with 10%, 32%, 42% and 11% for Geopolymer Concrete with Recycled Aggregate (GCRA), 9%, 52%,31% and 17% for geopolymer concrete with natural aggregate (GCNA), 10%, 19%,26% and 12% for Normal Concrete with Natural Aggregate (NCNA) and 23%, 19%, 67% and 14% for Normal Concrete with Recycled Aggregate (NCRA), respectively.

scholarly journals Effect of Recycled Coarse Aggregates in Properties of Concrete

2008 ◽  
Vol 3 (4) ◽  
pp. 130-137 ◽  
Author(s):  
R Kumutha ◽  
K Vijai
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Coarse Aggregate ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
The Cost

The properties of concrete containing coarse recycled aggregates were investigated. Laboratory trials were conducted to investigate the possibility of using recycled aggregates from the demolition wastes available locally as the replacement of natural coarse aggregates in concrete. A series of tests were carried out to determine the density, compressive strength, split tensile strength, flexural strength and modulus of elasticity of concrete with and without recycled aggregates. The water cement ratio was kept constant for all the mixes. The coarse aggregate in concrete was replaced with 0%, 20%, 40%, 60%, 80% and 100% recycled coarse aggregates. The test results indicated that the replacement of natural coarse aggregates by recycled aggregates up to 40% had little effect on the compressive strength, but higher levels of replacement reduced the compressive strength. A replacement level of 100% causes a reduction of 28% in compressive strength, 36% in split tensile strength and 50% in flexural strength. For strength characteristics, the results showed a gradual decrease in compressive strength, split tensile strength, flexural strength and modulus of elasticity as the percentage of recycled aggregate used in the specimens increased. 100% replacement of natural coarse aggregate by recycled aggregate resulted in 43% savings in the cost of coarse aggregates and 9% savings in the cost of concrete.

scholarly journals The effect of the aggregate type on the properties of pavement concrete

2018 ◽  
Vol 67 (4) ◽  
pp. 83-94
Author(s):  
Grzegorz Rogojsz ◽  
Damian Skupski ◽  
Bartosz Januszewski
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Modulus Of Elasticity ◽  
Frost Resistance ◽  
Laboratory Tests ◽  
Indirect Tensile Strength ◽  
Cement Concrete ◽  
Pore Characteristics ◽  
Road Surfaces ◽  
Indirect Tensile

This paper presents the results of laboratory tests on the properties of cement concrete containing various types of aggregate. The purpose of the tests was to determine the effect of aggregate on compressive strength, indirect tensile strength, air pore characteristics, frost resistance and the modulus of elasticity of concrete for road surfaces. The aggregate that meets the requirements for road concrete was determined on the basis of the tests. Keywords: road concrete, frost resistance of aggregate, frost resistance of road concrete.

scholarly journals Engineering Properties of Hybrid Fibre Reinforced Ternary Blend Geopolymer Concrete

2021 ◽  
Vol 5 (8) ◽  
pp. 203
Author(s):  
V. Sathish Kumar ◽  
N. Ganesan ◽  
P. V. Indira
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Engineering Properties ◽  
Ternary Blend ◽  
Geopolymer Concrete ◽  
Polypropylene Fibres ◽  
Hybrid Form ◽  
Steel Fibres

The primary aim of this research is to find an alternative for Portland cement using inorganic geopolymers. This study investigated the effect of steel and polypropylene fibres hybridisation on ternary blend geopolymer concrete (TGPC) engineering properties using fly ash, ground granulated blast furnace slag (GGBS) and metakaolin as the source materials. The properties like compressive strength, splitting tensile strength, flexural strength and modulus of elasticity of ternary blend geopolymer concrete. The standard tests were conducted on TGPC with steel fibres, polypropylene fibres and a combination of steel and polypropylene fibres in hybrid form. A total number of 45 specimens were tested and compared to determine each property. The grade of concrete considered was M55. The variables studied were the volume fraction of fibres, viz. steel fibres (0%, 0.5% and 1%) and polypropylene fibres (0%, 0.1%, 0.15%, 0.2% and 0.25%). The experimental results reveal that the addition of fibres in a hybrid form enhances the mechanical properties of TGPC. The increase in the compressive strength was nominal, and a significant improvement was observed in splitting tensile strength, flexural strength, and modulus of elasticity. Also, an attempt to obtain the relation between the different engineering properties was made with different volume fractions of fibre.

scholarly journals Economical Reactive Powder Concrete Cast Using Available Materials in North Sinai, Egypt

2013 ◽  
Vol 59 (2) ◽  
pp. 175-195 ◽  
Author(s):  
Nageh N. Meleka ◽  
Alaa A. Bashandy ◽  
Mohamed A. Arab
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Silica Fume ◽  
Modulus Of Elasticity ◽  
Steel Fibers ◽  
Indirect Tensile Strength ◽  
Reactive Powder Concrete ◽  
Indirect Tensile ◽  
Reactive Powder ◽  
North Sinai

Abstract In this research reactive powder concrete (RPC) was prepared using sand from North Sinai. The mechanical properties of locally cast RPC were investigated and evaluated by studying the effects of using different cement and silica fume contents and new steel fibers’ aspect ratios as reinforcement for RPC. Specimens’ preparation, curing regimes and testing procedures to evaluate the compressive strength, the modulus of elasticity, the indirect tensile strength and the flexural strength were discussed. A compressive strength of 154.5MPa, indirect tensile strength of 11.98MPa, modulus of elasticity of 45.1GPa and flexural strength of 30.26MPa have been achieved for reinforced RPC contains 800 kg/m3 cement content and silica fume content 30% of cement weight. The test results showed some improvements by increasing cement and silica fume contentsas well as adding steel fibers on the compressive strength, modulus of elasticity and indirect tensile strength.

scholarly journals Strength Characteristics of Cement-Rice Husk Ash Stabilised Sand-Clay Mixture Reinforced with Polypropylene Fibers

2018 ◽  
Vol 13 (4) ◽  
pp. 447-474 ◽  
Author(s):  
Ali Ghorbani ◽  
Maysam Salimzadehshooiili ◽  
Jurgis Medzvieckas ◽  
Romualdas Kliukas
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Rice Husk ◽  
Unconfined Compressive Strength ◽  
Rice Husk Ash ◽  
Indirect Tensile Strength ◽  
Polypropylene Fibres ◽  
Indirect Tensile ◽  
Improvement Index

In this paper, stress-strain behaviour of sand-clay mixture stabilised with different cement and rice husk ash percentages, and reinforced with different polypropylene fibre lengths are evaluated. Mixtures are widely used in road construction for soil stabilisation. It is observed that replacing half of the cement percentage (in high cement contents) with rice husk ash will result in a higher unconfined compressive strength. In addition, the presence of 6 mm polypropylene fibres will help to increase the unconfined compressive strength of stabilised samples, while larger fibres cause reverse behaviour. In addition, introducing a new index for assessing the effect of curing days. Curing Improvement Index it is obtained that larger fibres show higher Curing Improvement Index values. Results gained for the effects of curing days, and fibre lengths are further discussed and interpreted using Scanning Electron Microscopy photos. Based on the conducted Unconfined Compressive Strength, Indirect Tensile Strength, and Flexural Strength tests and using evolutionary polynomial regression modelling, some simple relations for prediction of unconfined compressive strength, indirect tensile strength, and flexural strength of cement-rice husk ash stabilised, and fibre reinforced samples are presented. High coefficients of determination of developed equations with experimental data show the accuracy of proposed relationships. Moreover, using a sensitivity analysis based on Cosine Amplitude Method, cement percentage and the length of polypropylene fibres used to reinforce the stabilised samples are respectively reported as the most and the least effective parameters on the unconfined compressive strength of specimens.

scholarly journals Alternative Using of Fine Aggregate in Concrete with Acid Curing

2021 ◽  
Vol 921 (1) ◽  
pp. 012063
Author(s):  
D Sandy ◽  
S R Tonapa
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Relative Strength ◽  
Indirect Tensile Strength ◽  
Fine Aggregate ◽  
Concrete Technology ◽  
Relative Percentage ◽  
A Value ◽  
Indirect Tensile

Abstract One of the most widely used construction materials is concrete. Concrete technology is currently developing, one of which is looking for alternative materials concrete forming. This research focuses on the use of slag as a fine aggregate in concrete, especially in environments containing sulfuric and chloride acid. Observations were made by testing compressive strength, indirect tensile strength, and flexural strength, with 171 cylindrical specimens and 27 sample beam specimens. The test results show that the relative percentage of compressive strength of normal concrete on H2SO4 curing against normal curing decreased 1.85% and 2.58% on HCl curing. The biggest reduction in the percentage of concrete compressive strength was found in 30% slag substitution with a value 8.42%, while the percentage reduction in the relative strength of the indirect tensile strength concrete is found in concrete with a slag substitution of 35% with a value 9.26%. As well as the decrease in relative percentage of flexural strength was found in 35% slag substitution with a value 12.84%. Although there is a decrease in each characteristic of concrete, slag material can be used as a constituent for concrete under environmental conditions of sulfuric acid and chloride acid.

scholarly journals Mechanical Properties of Thermal Ash Aggregate Content in Geopolymer Concrete

2020 ◽  
Vol 8 (6) ◽  
pp. 3954-3957
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Mix Design ◽  
Geopolymer Concrete ◽  
Replacement Level ◽  
Split Tensile Strength ◽  
Aggregate Content ◽  
Natural Aggregate

Elimination of cement in concrete was found to get increased with the introduction of geopolymer concrete. In that geopolymer concrete, natural aggregate was replaced by artificial thermal ash aggregate. The mix design was arrived by trail. The replacement level of artificial aggregate was 20, 40, 60, 80 and 100 percentages by weight of natural aggregate. The results of workability and mechanical properties of the mixes are find to be good. About 135% in compressive strength, 15% in split tensile strength and 987% in flexural strength was find to be increased.

Materials for Well Integrity: Characterization of Short-Term Mechanical Properties

2020 ◽  
Author(s):  
Mohammadreza Kamali ◽  
Mahmoud Khalifeh ◽  
Arild Saasen ◽  
Laurent Delabroy
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Strength Reduction ◽  
Indirect Tensile Strength ◽  
Short Term ◽  
Indirect Tensile ◽  
Expansive Cement

Abstract Integrated zonal isolation is well-known as a key parameter for safe drilling operation and well completion of oil and gas wells. An extensive research on alternative materials has been conducted in the past concerning primary cementing, overcoming annular leaks, and permanent well abandonment. The present article focuses on geopolymers, expansive cement, pozzolan based sealant and thermosetting resins. The viscous behavior and the pumpability of the different materials have been investigated and benchmarked with the properties of neat class G Portland cement. The current study includes short-term mechanical properties of the above-mentioned materials. These properties include compressive strength development, Young’s modulus, indirect tensile strength, and sonic strength. The tests are performed in accordance with API 10B-2 and ASTM D3967-16 for all the materials for 1, 3, 5, and 7-day of curing at 90°C and elevated (172 bar) and atmospheric pressures. Our results show a mixed behavior from the materials. According to uniaxial compressive test results, all the candidate barrier materials developed strength during the considered period; however, the geopolymer and pozzolanic-based mixture did not develop early strength. The expansive cement showed an acceptable early compressive strength, but strength reduction was noticed after some time. The strength reduction of expansive cement was also observed for the indirect tensile strength. All the materials become stiffer overtime as they made more strength. For the neat class G cement and expansive cement, the Young’s modulus showed a minimum after 5 days, but it was increased.

scholarly journals Production of lightweight Geopolymer concrete using artificial local lightweight aggregate

2018 ◽  
Vol 162 ◽  
pp. 02024
Author(s):  
Waleed Abbas ◽  
Wasan Khalil ◽  
Ibtesam Nasser
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Experimental Tests ◽  
Pulse Velocity ◽  
Dry Density ◽  
Geopolymer Concrete

Due to the rapid depletion of natural resources, the use of waste materials and by-products from different industries of building construction has been gaining increased attention. Geopolymer concrete based on Pozzolana is a new material that does not need the presence of Portland cement as a binder. The main focus of this research is to produce lightweight geopolymer concrete (LWGPC) using artificial coarse lightweight aggregate which produced from locally available bentonite clays. In this investigation, the binder is low calcium fly ash (FA) and the alkali activator is sodium hydroxide and sodium silicate in different molarities. The experimental tests including workability, fresh density, also, the compressive strength, splitting tensile strength, flexural strength, water absorption and ultrasonic pulse velocity at the age of 7, 28 and 56 days were studied. The oven dry density and thermal conductivity at 28 days age are investigated. The results show that it is possible to produce high strength lightweight geopolymer concrete successfully used as insulated structural lightweight concrete. The 28-day compressive strength, tensile strength, flexural strength, dry density, and thermal conductivity of the produced LWGPC are 35.8 MPa, 2.6MPa, 5.5 MPa, 1835kg/m3, and 0.9567 W/ (m. K), respectively.

scholarly journals Research on the Effect of Cooper Slag as a Fine Aggregate on the Properties of Concrete

2019 ◽  
Vol 8 (2S3) ◽  
pp. 619-623
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Copper Slag ◽  
Splitting Tensile Strength ◽  
Copper Recovery ◽  
Concrete Mixture ◽  
Copper Smelting ◽  
Fine Aggregate

Copper slag is a rough blasting grit or a by-product acquired by the process of copper smelting and refining. These copper slags are recycled for copper recovery. In this paper, we analysed copper slag’s feasibility and evaluate its total competence in M25 grade concrete. In this observation, a concrete mixture is applied with copper slag as a fine aggregate ranging from 0%, 20%, 40%, 60%, 80%, and 100% respectively. The strength of copper slag’s implementation is accomplished on the basis of concrete’s flexural strength, compressive strength and splitting tensile strength. From the obtained results, in concrete 40% percentage of copper slag is used as sand replacement. On 28 days, the modulus of elasticity increased up to 32%, the compressive strength increased up to 34% and flexural strength is increased to 6.2%. From this experiment, it is proved technically that replacing sand using copper slag as a fine mixture in M25 grade concrete.

Sign in / Sign up

Export Citation Format

Share Document