scholarly journals Economical Reactive Powder Concrete Cast Using Available Materials in North Sinai, Egypt

2013 ◽  
Vol 59 (2) ◽  
pp. 175-195 ◽  
Author(s):  
Nageh N. Meleka ◽  
Alaa A. Bashandy ◽  
Mohamed A. Arab
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Silica Fume ◽  
Modulus Of Elasticity ◽  
Steel Fibers ◽  
Indirect Tensile Strength ◽  
Reactive Powder Concrete ◽  
Indirect Tensile ◽  
Reactive Powder ◽  
North Sinai

Abstract In this research reactive powder concrete (RPC) was prepared using sand from North Sinai. The mechanical properties of locally cast RPC were investigated and evaluated by studying the effects of using different cement and silica fume contents and new steel fibers’ aspect ratios as reinforcement for RPC. Specimens’ preparation, curing regimes and testing procedures to evaluate the compressive strength, the modulus of elasticity, the indirect tensile strength and the flexural strength were discussed. A compressive strength of 154.5MPa, indirect tensile strength of 11.98MPa, modulus of elasticity of 45.1GPa and flexural strength of 30.26MPa have been achieved for reinforced RPC contains 800 kg/m3 cement content and silica fume content 30% of cement weight. The test results showed some improvements by increasing cement and silica fume contentsas well as adding steel fibers on the compressive strength, modulus of elasticity and indirect tensile strength.

scholarly journals The effect of the aggregate type on the properties of pavement concrete

2018 ◽  
Vol 67 (4) ◽  
pp. 83-94
Author(s):  
Grzegorz Rogojsz ◽  
Damian Skupski ◽  
Bartosz Januszewski
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Modulus Of Elasticity ◽  
Frost Resistance ◽  
Laboratory Tests ◽  
Indirect Tensile Strength ◽  
Cement Concrete ◽  
Pore Characteristics ◽  
Road Surfaces ◽  
Indirect Tensile

This paper presents the results of laboratory tests on the properties of cement concrete containing various types of aggregate. The purpose of the tests was to determine the effect of aggregate on compressive strength, indirect tensile strength, air pore characteristics, frost resistance and the modulus of elasticity of concrete for road surfaces. The aggregate that meets the requirements for road concrete was determined on the basis of the tests. Keywords: road concrete, frost resistance of aggregate, frost resistance of road concrete.

scholarly journals Effect of Iron Filings on the Mechanical Properties of Different Types of Sustainable Concrete

2018 ◽  
Vol 12 (1) ◽  
pp. 441-457 ◽  
Author(s):  
Sahar Jabbar Alserai ◽  
Wissam Kadhim Alsaraj ◽  
Zina Waleed Abass
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Indirect Tensile Strength ◽  
Recycled Aggregate ◽  
Geopolymer Concrete ◽  
Normal Concrete ◽  
Natural Aggregate ◽  
Indirect Tensile

Introduction:One of Iraq’s major environmental problems is a large amount of residual iron produced by the industrial sector, which is stored in domestic waste and landfills. The reuse of construction waste gives two aims, the first is to remove large quantities of pollution resulted from these waste, the second provides cheap resources for concrete aggregates.Methods:This study conducted a series of experiments and tests to test the feasibility of reusing this iron slag and recycled concrete aggregate in concrete mixtures. Different percentages of iron filings were used in the concrete mixture at 0, 0.5%, 0.75% and 1%. Tests are done to evaluate the quality of cast iron concrete which include compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) for four sustainable concretes.Results and Conclusion:The results show that the iron filings amount is increased to 1.0% which resulted in increasing percentage of compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) with 10%, 32%, 42% and 11% for Geopolymer Concrete with Recycled Aggregate (GCRA), 9%, 52%,31% and 17% for geopolymer concrete with natural aggregate (GCNA), 10%, 19%,26% and 12% for Normal Concrete with Natural Aggregate (NCNA) and 23%, 19%, 67% and 14% for Normal Concrete with Recycled Aggregate (NCRA), respectively.

scholarly journals Experimental comparative study of reactive powder concrete: mechanical properties and the effective factors

2018 ◽  
Vol 162 ◽  
pp. 04004 ◽  
Author(s):  
Eyad Kadhem ◽  
Ammar Ali ◽  
Sameh Tobeia
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Modulus Of Elasticity ◽  
High Performance ◽  
High Performance Concrete ◽  
Splitting Tensile Strength ◽  
Steel Fibers ◽  
Reactive Powder Concrete ◽  
Concrete Mechanical Properties ◽  
Reactive Powder

Reactive Powder Concrete (RPC) is a type of ultra-high performance concrete, this dense composite material generally characterized by high cement content, high durability, low porosity, low water/cement ratio and in most cases contains steel fibers as new types of concrete appears, further investigation for their mechanical properties are needed. This work aims to give a better understanding of RPC behavior by deriving formulas to calculate the modulus of elasticity and the splitting tensile strength in relation with compressive strength and steel fibers content. This study is based on data obtained from the experimental investigation done in this work and from others pervious works. The parametric study is based mainly on the silica fume content which is used in four different ratios (12 %, 15 %, 20 % and 25 %), the use of micro steel fibers 15 mm in length, 0.2 mm in diameter and aspect ratio of 75 added in ratios of (0 %, 1 %, 1.5 % and 2 %), and water/cement in ratios of (16 %, 18 %, 20 % and 22 %), respectively. The proposed equations show a better behavior in comparison to some available equations that were used in the estimation of modulus of elasticity and splitting tensile strength of reactive powder concrete, the coefficient of variation for the proposed equations (COV) decrease to 10.677% and 10.455% respectively.

scholarly journals Effect of Steel Fibers and Temperature on the Mechanical Properties of Reactive Powder Concrete

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Mahmoud Ahmed Ali Abdelrahim ◽  
Aboelwafa Elthakeb ◽  
Usama Mohamed ◽  
Mohamed Taha Noaman
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elevated Temperatures ◽  
Fine Sand ◽  
Splitting Tensile Strength ◽  
Steel Fibers ◽  
Reactive Powder Concrete ◽  
Strain Relationship ◽  
Reactive Powder

Abstract Reactive Powder Concrete (RPC) is a concrete of the modern generation it mainly contains a high percentage of cement and a small percentage of water For cement as well as the presence of fine sand, ground quartz and silica dust. This research aims Studying the behavior and mechanical characteristics of RPC exposed to elevated temperatures. The key variables in this study are steel fibers content and the high temperatures of different levels 25, 200, 300, 400 ºC. Mechanical properties of concrete behavior including compressive strength, splitting tensile strength, stress-strain relationship (modulus of elasticity), and flexural strength. The test findings indicated that the Output strength of RPC specimens decreased when the high temperature increases. At a temperature of 400 °C, all samples lost the compressive strength and splitting tensile strength.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

scholarly journals Influence of Partial Replacement of Micro-Silica by Fly-Ash on Strength Properties of Reactive Powder Concrete

2020 ◽  
Vol 9 (3) ◽  
pp. 2932-2937
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Performance ◽  
Cementitious Materials ◽  
Partial Replacement ◽  
Reactive Powder Concrete ◽  
Experimental Investigations ◽  
Reactive Powder ◽  
Micro Silica

Reactive powder concrete (RPC) is the ultra-high strength concrete made by cementitious materials like silica fumes, cement etc. The coarse aggregates are completely replaced by quartz sand. Steel fibers which are optional are added to enhance the ductility. Market survey has shown that micro-silica is not so easily available and relatively costly. Therefore an attempt is made to experimentally investigate the reduction of micro-silica content by replacing it with fly-ash and mechanical properties of modified RPC are investigated. Experimental investigations show that compressive strength decreases gradually with addition of the fly ash. With 10 per cent replacement of micro silica, the flexural and tensile strength showed 40 and 46 per cent increase in the respective strength, though the decrease in the compressive strength was observed to be about 20 per cent. For further percentage of replacement, there was substantial drop in compressive, flexural as well as tensile strength. The experimental results thereby indicates that utilisation of fly-ash as a partial replacement to micro silica up to 10 per cent in RPC is feasible and shows quite acceptable mechanical performance with the advantage of utilisation of fly-ash in replacement of micro-silica.

Materials for Well Integrity: Characterization of Short-Term Mechanical Properties

2020 ◽  
Author(s):  
Mohammadreza Kamali ◽  
Mahmoud Khalifeh ◽  
Arild Saasen ◽  
Laurent Delabroy
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Strength Reduction ◽  
Indirect Tensile Strength ◽  
Short Term ◽  
Indirect Tensile ◽  
Expansive Cement

Abstract Integrated zonal isolation is well-known as a key parameter for safe drilling operation and well completion of oil and gas wells. An extensive research on alternative materials has been conducted in the past concerning primary cementing, overcoming annular leaks, and permanent well abandonment. The present article focuses on geopolymers, expansive cement, pozzolan based sealant and thermosetting resins. The viscous behavior and the pumpability of the different materials have been investigated and benchmarked with the properties of neat class G Portland cement. The current study includes short-term mechanical properties of the above-mentioned materials. These properties include compressive strength development, Young’s modulus, indirect tensile strength, and sonic strength. The tests are performed in accordance with API 10B-2 and ASTM D3967-16 for all the materials for 1, 3, 5, and 7-day of curing at 90°C and elevated (172 bar) and atmospheric pressures. Our results show a mixed behavior from the materials. According to uniaxial compressive test results, all the candidate barrier materials developed strength during the considered period; however, the geopolymer and pozzolanic-based mixture did not develop early strength. The expansive cement showed an acceptable early compressive strength, but strength reduction was noticed after some time. The strength reduction of expansive cement was also observed for the indirect tensile strength. All the materials become stiffer overtime as they made more strength. For the neat class G cement and expansive cement, the Young’s modulus showed a minimum after 5 days, but it was increased.

Development of High Performance Concrete Containing Admixture in Nuclear Power Plants

2013 ◽  
Vol 357-360 ◽  
pp. 1062-1065 ◽  
Author(s):  
Jeong Eun Kim ◽  
Wan Shin Park ◽  
Song Hui Yun ◽  
Do Gyeum Kim ◽  
Jea Myoung Noh
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Modulus Of Elasticity ◽  
Blast Furnace Slag ◽  
High Performance ◽  
Splitting Tensile Strength ◽  
Furnace Slag

This paper presents the results of an experimental study on the compressive strength, splitting tensile strength and modulus of elasticity characteristics of high performance concrete. These tests were carried out to evaluate the mechanical properties of HPC for up to 7 and 28 days. Mixtures were prepared with water to binder ratio of 0.40. Two mixtures were containing fly ash at 25%, silica fume at 5% cement replacement, respectively. Another mixture was contains blast furnace slag and fly ash at 25%. Three standard 100¥a200 cylinder specimens were prepared. HPC showed improvement in the compressive strength and splitting tensile strength when ordinary Portland cement was replaced with silica fume. Compare with specimens FA25 and BS25FA25, specimen SF5 showed much more modulus of elasticity. It shows that the use of the blast furnace slag of 25% and fly ash of 25% cement replacement has caused a small increase in compressive strength and splitting tensile strength and modulus of elasticity compared to the only use of fly ash of 25% at 28days. The results indicated that the use of blast furnace slag or silica fume provided the good performance compare to fly ash when the mechanical properties of the high performance concretes were taken into account.

scholarly journals Properties of Reactive Powder Concrete Using Local Materials and Various Curing Conditions

2019 ◽  
Vol 4 (6) ◽  
pp. 74-83 ◽  
Author(s):  
Gamal I. K. ◽  
K. M. Elsayed ◽  
Mohamed Hussein Makhlouf ◽  
M. Alaa
Keyword(s):  
Compressive Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Steel Fiber ◽  
High Strength ◽  
Hot Water ◽  
Reactive Powder Concrete ◽  
Normal Water ◽  
Reactive Powder ◽  
Local Materials

Reactive Powder Concrete RPC is comprise of (cement, quartz powder, sand, and superplasticizer) mixture with low water/cement ratio. It has not coarse aggregates and characterized by highly dense matrix, high strength concrete, excellent durability, and economic. This study aims to investigate fresh and hardened properties of locally cast RPC with several available economical materials such as silica fume (SF), fly ash (FA), steel fiber (STF), and glass fiber (GF). Experimental investigation were performed to study the effectiveness of partial replacement of cement by SF or FA to reach ultra-high strength concrete, effect of additional materials STF or GF in order to improve the fracture properties of the RPC mixes, and influence of the treated with normal water as well as with hot water. Fifteen different RPC mixes were cast with 20, 25, 30, and 35% cement replacement by SF, 25% cement replacement by FA, and another proportions taken combination between SF and FA with percentages 15, 20, 25% FA and constant 10% SF. Varying fiber types (steel fiber or glass fiber) added to concrete by different percentages 1, 2, and 3%. Specimens were treated with normal water 25ᵒC and hot water at 60ᵒC and 90ᵒC by 2 mixes with silica fume content 25% of binder and steel fiber content 2% by total volume. Performance of the various mixes is tested by the slump flow, compressive strength, flexure strength, splitting tensile strength, and density. The production of RPC using local materials is successfully get compressive strength of 121 MPa at the age of 28 days at standard conditions and normal water curing 25°C with Silica fume content 25% of binder and steel fiber content 2% by total volume of RPC and water/binder ratio of 0.25.  The results also showed the effect of curing by hot water 60 and 90°C, it is observed that compressive strength increases proportionally with curing temperatures and a compressive strength of 149.1 MPa at 90°C for 1days was obtained.

scholarly journals Experimental Behaviour of Fiber Reinforced Reactive Powder Concrete

2019 ◽  
Vol 9 (1S3) ◽  
pp. 454-459 ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Polypropylene Fiber ◽  
Chloride Diffusion ◽  
Sisal Fiber ◽  
Reactive Powder Concrete ◽  
Coir Fiber ◽  
Split Tensile Strength ◽  
Reactive Powder

In this paper various mix proportions of Reactive Powder Concretes were formulated using ordinary Portland cement, Fly ash, Micro silica, Silica Fume, Quartz powder etc and these concretes were subjected to strength test. The best mix was selected for further in depth study with fibers like Sisal fiber, Coir fiber, Hair fiber and Polypropylene fiber mixed Reactive Powder Concrete and the various tests have been performed Cube Compressive strength, Cylinder Compressive strength, Flexural strength, Split Tensile strength, Shear test, Water absorption, Sorptivity and Chloride diffusion etc. As a result, fiber incorporated concrete shows increasing Flexural strength, splitting tensile strength, and shear strength up to 30% as compared to control RPC and gives minimal decrease in compressive strength by the addition of fibers. These characteristics make it as a promising material for casting non structural elements such as pressure pipes, flooring tiles, Partition panels, door and window frames. It can also be used as repair materials.

Sign in / Sign up

Export Citation Format

Share Document