scholarly journals Influence of the Arabic-Coffee on the Overall Color of Glazed or Polished Porcelain Veneers – In vitro Study

2019 ◽  
Vol 13 (1) ◽  
pp. 364-370 ◽  
Author(s):  
Nabiel Alghazali ◽  
Afaf A. Hakami ◽  
Ghadah A. AlAjlan ◽  
Rawan M. Alotaibi ◽  
Faris N. Alabdulwahab ◽  
...  
Keyword(s):  
Colour Change ◽  
In Vitro Study ◽  
Color Stability ◽  
Color Changes ◽  
Significant Difference ◽  
Oral Environment ◽  
Before And After ◽  
Feldspathic Porcelain

Background: Sometimes, porcelain restorations experience some degree of colour change in oral environment, which could be related to the quality of diet and surface roughness of these restorations. Objective: The aim of this in-vitro study was to evaluate the influence of Arabic-Coffee on the overall color of glazed or polished porcelain veneers fabricated from four different porcelain materials and two different thicknesses. Materials and Methods: A total of 160 porcelain disc of tested specimens were fabricated to a standardized thickness of 1.00 mm and 0.6mm using the following materials: Feldspathic porcelain, Zircon, E-max Press, and E-max CAD; (80 discs for each thickness and 20 specimens of each material used). Veneer specimens from each material were randomly divided into two subgroups (n = 10): 10 specimens were kept as glazed, were the other 10 tested specimens were adjusted with diamond burs, and then polished with Ivoclar Vivadent ceramic polishing kits using the recommended protocol for polishing provided by the company. A color of all tested specimens was measured using Vita Easy Shade Spectrophotometer. Then, all specimens were immersed in Arabic coffee (Al Mosafer Coffee, Saudi Arabia) and theromcycled for 1 week, and the colors of all tested specimens were then recorded again. Results: It was shown that there is a significant difference in the average color changes before and after immersing in Arabic-Coffee for all materials and thicknesses used in the current study. In-addition, significant differences in color changes were noticed between glazed and polished specimens. Moreover, colour change caused by the coffee was not significantly related to the thickness of the specimens used. Conclusion: Color stability of porcelain materials could be affected by surface treatment whether glazing or polishing. All aesthetic restorations should be deglazed whenever any adjustments have been done to maintain the color match and stability in an oral environment. Also, Arabic-Coffee is considered as a staining drink to a limited extend where patient should be assured to maintain their oral health to maintain the colour stability of their restorations.

The Effect of Bleaching Agents on the Color Stability of Ceromer and Porcelain Restorative Materials In Vitro

2012 ◽  
Vol 38 (1) ◽  
pp. E1-E8 ◽  
Author(s):  
HB Kara ◽  
F Aykent ◽  
B Ozturk
Keyword(s):  
Color Change ◽  
Glass Ceramics ◽  
In Vitro Study ◽  
Color Stability ◽  
Color Changes ◽  
Bleaching Procedure ◽  
Significant Difference ◽  
Restorative Materials ◽  
The Difference

SUMMARY Purpose The aim of this in vitro study was to determine the color changes of five different restorative materials after exposing these materials to two different home bleaching agents. Methods This study applied bleaching agents to an ultralow-fusing porcelain, a low-fusing porcelain, two types of heat-pressed glass ceramics, and a ceromer. A total of 24 disc-shaped specimens were fabricated (with a diameter of 10 mm and a thickness of 2 mm) from each material (n=12). The initial color measurements were taken with a spectrophotometer. The first set of specimens were bleached with 10% hydrogen peroxide (HP) for one hour daily for 10 days. The other set of specimens were bleached with 10% carbamide peroxide (CP) bleaching gel for eight hours daily for 14 days. Data were analyzed with the one-way analysis of variance and Kruskal-Wallis statistical test. The difference in the prebleaching and postbleaching color of each material was considered to be statistically significant at p < 0.05. Results The study found a statistically significant difference among the color changes of the test groups after exposing them to both bleaching agents (p<0.05). Appreciable color change was observed in the Estenia (ΔE=3.99) specimens that were bleached with the HP, and noticeable color changes were observed in the Estenia (ΔE=1.89) and IPS Empress 2 (ΔE=1.66) groups when they were treated with the CP. Conclusions Restorations (especially polymer-containing restorative materials) should be protected before any bleaching procedure due to the high risk of color change.

Effect of Children's Drinks on Color Stability of Different Dental Composites: An in vitro Study

2017 ◽  
Vol 41 (2) ◽  
pp. 120-125 ◽  
Author(s):  
Ahmed Nour El-din Ahmed Habib ◽  
Soad Abdelmoniem Abdelmoniem ◽  
Sara Ahmed Mahmoud
Keyword(s):  
Color Change ◽  
In Vitro Study ◽  
Color Stability ◽  
Dental Composites ◽  
Chocolate Milk ◽  
Water Control ◽  
Color Changes ◽  
Significant Difference ◽  
Mango Juice

Aim: To assess the effect of four different children's drinks on color stability of resin dental composites. Study design: A total of one hundred and twenty specimens were prepared from Grandio SO, Filtek Z350 XT and Filtek Z250 XT (forty specimens each). Specimens were thermocycled, then each group was further subdivided into four subgroups (n=10) according to the immersion media which were chocolate milk, mango juice, orange fizzy drink, and water (control). The initial color parameters of each specimen were recorded before immersion (baseline) and color change values were recorded three and seven days after immersion in each solution using a digital spectrophotometer. Atomic force microscope was used to measure the surface roughness in randomly selected samples after one week immersion in children's drinks. Results: All the children's drinks produced color changes in the examined resin dental composites, yet there was no statistical significant difference between the effects of tested drinks on the color changes (mean ΔE) of the three different dental composites (P>0.05). Conclusions: All tested children's drinks caused clinically unacceptable color changes of the tested resin dental composites. Immersion in chocolate milk and orange fizzy led to the highest color changes in the tested resin dental composites.

scholarly journals The difference of the salivary volume before and after drinking the rosella tea (Hibiscus sabdariffa)

2010 ◽  
Vol 22 (3) ◽  
Author(s):  
Mutiara Indah Permata Sari Islami ◽  
Edeh Roletta Haroen ◽  
Sri Tjahajawati
Keyword(s):  
In Vitro Study ◽  
T Test ◽  
Hibiscus Sabdariffa ◽  
Test Analysis ◽  
Community Benefits ◽  
Significant Difference ◽  
Before And After ◽  
Quasi Experimental ◽  
The Difference

Introduction: Roselle plants (Hibiscus sabdariffa) is one of the herbs that began to be used by the community. Benefits of this plant is quite a lot for health. The portion taken for consumption is the red flower petals. oselle tea is one of the sour beverages which can affect the salivary gland secretion. The purpose of this study is to analyzed the difference of salivary volume before and after drinking roselle tea. Methods: This study has been conducted to 40 students of Faculty of Dentistry, Padjadjaran University, ranging from 18-23 years of age with good general condition. This study is quasi-experimental in vitro study using the paired test analysis with α = 0,05 of the data collected from salivary volume. Results: The result of study indicates that the average of salivary volume before drinking roselle tea is 1,90 milliliter. After drinking roselle tea, the average of salivary volume is 4,54 milliliter. The result of paired test analysis shows that t-test is 16,172 and t-table is 2,022. The value of t-test > t-table. Result of statistic shown there is significant difference of salivary volume before and after drinking roselle tea. Conclusion: There is a difference of salivary volume before and after drinking roselle tea.

scholarly journals Study of microbial spread when using multiple-use nasal anaesthetic spray

2011 ◽  
Vol 49 (3) ◽  
pp. 281-285
Author(s):  
M. Rashid ◽  
Y.G. Karagama
Keyword(s):  
Colour Change ◽  
In Vitro Study ◽  
Spectrophotometric Analysis ◽  
Cross Infection ◽  
Multiple Use ◽  
Before And After ◽  
Xylocaine Spray ◽  
Economic Constraints ◽  
Fluorescein Dyes

Background: Current economic constraints have led to the emergence of reusable anaesthetic sprays with replacement nozzles (Xylocaine) as an alternative to disposable anaesthetic solutions (Co-phenylcaine) for rhinological procedures. The former costs 213.84 per year vers12,047.69 for the latter, at equivocal doses. However, research regarding the sterility of such instruments is limited. The aim of this in vitro study was to determine whether bottles of Xylocaine could pose a risk of cross-infection to patients. Methods: Two techniques were used. The first was to introduce nozzles into methylene blue and fluorescein dyes, and then analysing the anaesthetic solutions using spectrophotometry for assessment of colour change indicating retrograde contamination. The second method involved spraying Xylocaine into cultures of Staphylococcus aureus with concurrent nozzle changes. This was repeated over a 36-day-period. Sterility checks were performed on the Xylocaine before and after inoculation into the culture. Results: None of the anaesthetic solutions showed the presence of dyed saline following spectrophotometric analysis. No S. aureus was isolated from any of the 30 spray bottles cultures over the 36-day trial period. Conclusion: It was demonstrated that using the Xylocaine spray with disposable nozzles for each patient should not pose a cross infection risk to patients.

scholarly journals SEM characterization and ageing analysis on two generation of invisible aligners

2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Roberta Condò ◽  
Gianluca Mampieri ◽  
Aldo Giancotti ◽  
Loredana Cerroni ◽  
Guido Pasquantonio ◽  
...  
Keyword(s):  
Chemical Stability ◽  
In Vitro Study ◽  
Technological Evolution ◽  
Significant Weight Loss ◽  
Sem Images ◽  
Structural Alterations ◽  
Oral Environment ◽  
Before And After ◽  
Initial Hypothesis

Abstract Background The purpose of the in vitro study is to investigate and compare the morphological features and the chemical stability in weight of two different polyurethane-based blends, Smart Track (LD30) and Exceed30 (EX30), used for orthodontic aligners manufacture before and after the oral usage. Methods Twenty orthodontic aligners were randomly selected: 10 LD30 and 10 EX30, each group was divided in two subgroups, never used and intra-orally aged. By the employment of a Stereomicroscope, a section of 5 × 5 mm was cut from the buccal surface of the incisal region of each aligner. All samples were subjected to Scanning Electron Microscopy and Ageing tests in different solutions to simulate the hostility of the oral environment. The statistical method used was t-test. Results At SEM images, LD30 appears more homogeneous in texture respect to EX30. However, after clinical usage, both materials show significant structural alterations: findings have been supported by higher magnifications at SEM, by which it is clearly to observe many superficial cracks cross through the polymer structures of LD30U, absent in never used samples. LD30U surface becomes also smoother due to the disappearance of most of the conglomerates, but at the same time also rougher while EX30U shows a greater irregularity and porosity in which large and deep cracks are also highlighted. Although these changes occur persistently, in the aging tests no significant weight loss from both materials has been found, confirming the initial hypothesis of a good chemical stability and safety of both polyurethane mixtures even in conditions of severe hostility. Conclusion LD30 is the expression of the technological evolution of EX30, this is made evident above all by its morphological architecture, more homogeneous and defined but also by the chemical stability that can be appreciated even in evident critic situations.

scholarly journals Do Titanium Mini-Implants Have the Same Quality of Finishing and Degree of Contamination before and after Different Manipulations? An In Vitro Study

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 245
Author(s):  
Tatiana Zogheib ◽  
André Walter-Solana ◽  
Fernando de la Iglesia ◽  
Eduardo Espinar ◽  
Javier Gil ◽  
...  
Keyword(s):  
Contact Angle ◽  
Surface Defects ◽  
In Vitro Study ◽  
Surface Treatments ◽  
Carbon Plastic ◽  
Degree Of Contamination ◽  
Mini Implants ◽  
Before And After

Evaluate the quality of finishing and degree of contamination before and after handling and surface treatment of titanium (Ti) orthodontic mini-implants (OMIs). A scanning electron microscope (SEM) study on ninety-six titanium OMIs was done. Energy-Dispersive X-ray Analysis (EDX) identified the present particles on manufactured OMIs surfaces. Then, OMIs were manipulated with gauze (dry sterile, soaked in chlorhexidine) and gloves (latex, nitrile) to evaluate the contamination of these handling materials. Finally, OMIs underwent surface treatments and were placed in bone to observe the contaminants they released. Roughness (Ra) and wettability with contact angle parameter (CA) were measured on these treated OMIs. Machined OMIs presented surface irregularities and were contaminated with manufacturing-process particles (carbon, plastic Polyvinyl Chloride PVC, aluminum). Hand-manipulated OMIs were also contaminated by the handling materials. OMIs surface characteristics were as follows: acid-etched (Ra ≈ 1.3 μm, CA ≈ 66°), machined (Ra ≈ 0.3 μm, CA ≈ 68°), SB (Ra ≈ 3.3 μm, CA ≈ 78°), and SBAO (Ra ≈ 3.1 μm, CA ≈ 92°). Bone was contaminated by OMIs surface defects and extra particles. Manufactured OMIs have surface contaminants that increase with clinical handling. Surface treatments (SBAO, a combination of sandblasting and anodic oxidation) increase the roughness and contact angle, which play an important role in osseointegration. Surface-treated OMIs leave titanium particles in the bone during their insertion-removal. The use of a gauze soaked in chlorhexidine is recommended when handling OMIs. Further investigations would be interesting to study more variables and confirm the present results.

scholarly journals Does Modification of Amalgomer with Propolis Alter Its Physicomechanical Properties? An In Vitro Study

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Reham M. Abdallah ◽  
Amr M. Abdelghany ◽  
Neven S. Aref
Keyword(s):  
Compressive Strength ◽  
Color Change ◽  
In Vitro Study ◽  
Ethanolic Extract ◽  
Color Stability ◽  
Physicomechanical Properties ◽  
X Ray ◽  
Group I ◽  
Significant Difference

Objective. To assess if incorporating ethanolic extract of propolis into ceramic-reinforced glass ionomer (Amalgomer CR) might have an influence on its physicomechanical properties. Materials and Methods. Three groups were assessed; group I: Amalgomer CR (control) and two experimental groups (II and III) of propolis added to the liquid of Amalgomer CR with 25 and 50 v/v %, respectively. Evaluation parameters were color stability, compressive strength, microhardness, and surface roughness. Representative specimens of each group were analyzed by Fourier-transform infrared spectroscopy, energy-dispersive X-ray, X-ray diffraction, and scanning electron microscopy. Analysis of variance (ANOVA) was used to compare the results, followed by a Tukey post hoc test (p<0.05). Results. Nonsignificant color change for both groups of modified Amalgomer CR. Meanwhile, the two experimental groups exhibited a significant increase in both compressive strength and microhardness. Simultaneously, there was a significant difference in roughness values among groups with the lowest roughness values exhibited by the 50 v/v % propolis concentration. Conclusions. Modification of Amalgomer CR with 50 v/v % propolis may increase its mechanical properties without compromising its esthetic. Clinical Significance. Modification of Amalgomer CR by 50 v/v % propolis is supposed to be a hopeful restorative material with favorable characteristics.

scholarly journals Spectrophotometric and computerized evaluation of tooth bleaching employing 10 different home-bleaching procedures: In-vitro study

2014 ◽  
Vol 08 (04) ◽  
pp. 538-545 ◽  
Author(s):  
Cem Peskersoy ◽  
Ayhan Tetik ◽  
Veli Ozgen Ozturk ◽  
Necmi Gokay
Keyword(s):  
Digital Imaging ◽  
In Vitro Study ◽  
Vitro Study ◽  
Tooth Bleaching ◽  
Control Group ◽  
San Jose ◽  
Color Changes ◽  
Before And After ◽  
Effective Product

ABSTRACT Objective: The aim of this in-vitro study was to evaluate the efficacy of bleaching products, determine the applicability and validation of the measurement methods. Materials and Methods: Freshly extracted 110 human incisor teeth were stained with whole blood and hemolysate solution prior to the application of 10 different home-bleaching products. Spectrophotometric measurements of the tooth shades were performed for each specimen before and after bleaching at the 1st, 3rd, 7th, and 14 days. Differences in lightness (Δl), chroma (Δc), hue (Δh) values and shade changes were measured to evaluate process. Computerized digital imaging analyses to determine the color changes were performed with Photoshop CS4 software (Adobe, San Jose, CA, USA). Statistical analyses were performed with analysis of variance, Scheffe and Tukey tests. Results: In all of the test groups regardless of the material used, a significant increase in lightness and hue, and decrease of chroma were observed, as compared to the control group. After recommended bleaching applications, Δl and Δh values respectively increased in group Zaris White and Brite (ZWB) and group Pola Night and Δc values showed significant decrease in groups ZWB and Rembrandt REM3 (P < 0.05). At the end of the procedure both spectrophotometric and digital imaging analysis showed ZWB was the most effective product among the others while Yotuel and Happy Smile were the least (P < 0.05). Conclusions: Home-bleaching systems showed slower but almost permanent bleaching effect likewise office-based methods. Both software and spectrophotometric analyses have advantages such as evaluating the results objectively and numerically, also treatment outcomes could be preserved.

scholarly journals Shaping ability of two heat treated rotary NiTi instruments using different kinematics/in vitro study

2021 ◽  
Vol 45 (1) ◽  
Author(s):  
Engy M. Kataia ◽  
Mohamed Mokhtar Nagy ◽  
Mohamed M. Kataia ◽  
Hala Fayek Khalil
Keyword(s):  
In Vitro Study ◽  
Preparation Time ◽  
Heat Treated ◽  
Significant Difference ◽  
Before And After ◽  
Canal Transportation ◽  
Niti Instruments ◽  
Post Hoc ◽  
Shaping Ability

Abstract Background Comparing shaping ability of Azure and Fanta AF One in rotation and reciprocation. This study was conducted on 40 resin blocks, having canal curvatures 30°-angle and of 16-mm length. The blocks were assigned to 4-groups according to the instrument and motion used: Azure/Rotation (A/Rt), Fanta AF one/Rotation (F/Rt), Azure/Reciprocation (A/Rec) and Fanta AF one/Reciprocation (F/Rec). For both systems single file 25, taper 0.06 were used. Digital images were taken before and after instrumentation. Adobe Photoshop was used to overlap post and pre-instrumentation images to assess canal transportation at 1, 4, 7-mm; representing apical, middle and cervical levels respectively. Stopwatch was used to document the time taken for canal preparation. One-way ANOVA followed by Tukey post hoc test, used to compare between more than two groups in non-related samples. Results At the apical level, no statistically significant difference was found between both files in either rotation or reciprocation. However, reciprocation motion showed significantly lower transportation levels in both files. No significant difference was found among groups at the middle and cervical levels. Regarding preparation time, Reciprocation in both groups was significantly longer. Conclusions The use of reciprocation motion showed minimized apical canal transportation in both files however in longer preparation time.

Sign in / Sign up

Export Citation Format

Share Document