scholarly journals Effect of Calcination Temperature on the Synthesis of Silica from Bagasse

2021 ◽  
Vol 10 (2) ◽  
pp. 140-147
Author(s):  
Poedji Loekitowati Hariani ◽  
◽  
Fahma Riyanti ◽  
Desneli Desneli ◽  
Fatma Fatma ◽  
...  
Keyword(s):  
Surface Area ◽  
Calcination Temperature ◽  
Average Diameter ◽  
Silica Content ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Potential Source ◽  
Naoh Solution ◽  
Hcl Solution

Bagasse is the solid waste derived from the sugar-making process. A large amount of silica in bagasse is a potential source of silica. In this study, extraction of silica from bagasse was carried out in the following steps: pretreatment of bagasse using HCl solution, followed by calcination at varying temperatures (700 oC, 800 oC, and 900 ℃) using a furnace. Furthermore, extraction using NaOH solution and precipitation using HCl. Silica characteristics were obtained using X-Ray Diffraction (XRD), Scanning Electron Microscopy-Electron Dispersive Spectrometry (SEM-EDS), and BET surface area. The results showed that calcination temperature affected the characteristics of the silica produced. The silica extracted at 700℃ produced an amorphous phase with a broad peak at an angle of 2θ = 20-24°. It contained the most considerable silica content and surface area, 42.46% and 796.89 cm2/g, respectively. The extracted silica had an average diameter of 5.67 mm and a pore volume of 1.184 cm3/g.

scholarly journals Hydrochloric Acid Modification and Lead Removal Studies on Naturally Occurring Zeolites from Nevada, New Mexico, and Arizona

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1238
Author(s):  
Garven M. Huntley ◽  
Rudy L. Luck ◽  
Michael E. Mullins ◽  
Nick K. Newberry
Keyword(s):  
New Mexico ◽  
Surface Area ◽  
Bet Surface Area ◽  
Lead Removal ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Naturally Occurring ◽  
27Al Mas Nmr ◽  
Modified Zeolites

Four naturally occurring zeolites were examined to verify their assignments as chabazites AZLB-Ca and AZLB-Na (Bowie, Arizona) and clinoptilolites NM-Ca (Winston, New Mexico) and NV-Na (Ash Meadows, Nevada). Based on powder X-ray diffraction, NM-Ca was discovered to be mostly quartz with some clinoptilolite residues. Treatment with concentrated HCl (12.1 M) acid resulted in AZLB-Ca and AZLB-Na, the chabazite-like species, becoming amorphous, as confirmed by powder X-ray diffraction. In contrast, NM-Ca and NV-Na, which are clinoptilolite-like species, withstood boiling in concentrated HCl acid. This treatment removes calcium, magnesium, sodium, potassium, aluminum, and iron atoms or ions from the framework while leaving the silicon framework intact as confirmed via X-ray fluorescence and diffraction. SEM images on calcined and HCl treated NV-Na were obtained. BET surface area analysis confirmed an increase in surface area for the two zeolites after treatment, NM-Ca 20.0(1) to 111(4) m2/g and NV-Na 19.0(4) to 158(7) m2/g. 29Si and 27Al MAS NMR were performed on the natural and treated NV-Na zeolite, and the data for the natural NV-Na zeolite suggested a Si:Al ratio of 4.33 similar to that determined by X-Ray fluorescence of 4.55. Removal of lead ions from solution decreased from the native NM-Ca, 0.27(14), NV-Na, 1.50(17) meq/g compared to the modified zeolites, 30 min HCl treated NM-Ca 0.06(9) and NV-Na, 0.41(23) meq/g, and also decreased upon K+ ion pretreatment in the HCl modified zeolites.

scholarly journals Synthesis and Characterization of Co-Mo/γ-Alumina Catalyst from local Kaolin clay for Hydrodesulfurization of Iraqi Naphtha

2021 ◽  
Vol 11 (1) ◽  
pp. 84-106
Author(s):  
Nada Sadoon Ahmed zeki ◽  
Sattar Jalil Hussein ◽  
Khalifa K. Aoyed ◽  
Saad Kareem Ibrahim ◽  
Ibtissam K. Mehawee
Keyword(s):  
Surface Area ◽  
Sulfur Removal ◽  
Sulfuric Acid Concentration ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Mo Catalyst ◽  
Pressure Time ◽  
Al2o3 Catalyst

This work deals with the hydrodesulfurization of three types of naphtha feedstocks; mixednaphtha (WN), heavy naphtha (HN) & light naphtha (LN) with a sulfur content of 1642.1,1334.9 & 709 ppm respectively, obtained from Missan refinery using prepared Co-Mo/γ-Al2O3catalyst. The Iraqi white kaolin was used as a starting material for the preparation of γ-Al2O3support, transferring kaolin to meta-kaolin was studied through calcination at differenttemperatures and durations, kaolin structure was investigated using X-Ray diffractiontechniques.High purity 94.83%. Crystalline γ-Al2O3 with a surface area of 129.91 m2/gm, pore volume0.9002 cm3/g was synthesized by extraction of Iraqi kaolin with H2SO4 at different acid to clayweight ratios, acid concentrations & leaching time. Ethanol was used as precipitating agent; theresultant gel was dried and calcined at 70OC, 10 hrs & 900 OC, 2 hrs respectively.The effects of different parameters on the average crystallinity and extraction % ofsynthesized γ-Al2O3 were studied like; acid: clay ratio, sulfuric acid concentration, leachingtime, leaching temperature & kaolin conversion to metakaolin. Characterization of prepared γ-Al2O3 & Co-Mo catalyst were achieved by X-ray diffraction, FTIR-spectra, texture properties& BET surface area, BJH N2 adsorption porosity, AFM, SEM, crush strength & XRF tests. Co-Mo/ γ-Al2O3 catalyst with final loading 5.702 wt% and 21.45 wt% of Co and Mo oxidesrespectively was prepared by impregnation methods.The activity of prepared Co-Mo/γ-Al2O3 catalyst after moulding to be tested forhydrodesulfurization (HDS) of naphtha feedstock W.N, H.N & L.N was performed using apilot hydrotreating unit at petroleum research & development centre, at different operatingconditions. Effects of temperature, LHSV, pressure, time & pore size distribution were studied,the best percentage of sulfur removal is increased with decreasing LHSV to 2 hr-1 as a generaltrend to be 89.71, 99.72, 99.20 % at 310oC for the whole naphtha, heavy naphtha and lightnaphtha feedstocks respectively, at 34 bar pressure and 200/200 cm3/cm3 H2/HC ratio.

Vacuum Carburization of Nanometer Tungsten Powder with Carbon Black

2007 ◽  
Vol 534-536 ◽  
pp. 165-168 ◽  
Author(s):  
Luo Ji ◽  
Lin Tao ◽  
Zhi Meng Guo ◽  
Cheng Chang Jia
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Surface Area ◽  
Tungsten Powder ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
X Ray Scattering ◽  
Vacuum Carburization ◽  
Dta Curves

Vacuum carburization of nanometer tungsten powder was investigated in a simple designed apparatus. An X-Y recorder was used to plot differential thermal analysis (DTA) curves to determine the starting temperature of carburization of four samples with different specific surface area. The product was characterized by X-ray Diffraction (XRD) and small angle X-ray scattering (SAXS). The results show that finer tungsten powder has lower starting temperature of carburization. Tungsten powder, the BET surface area of which is 32.97m2/g, was completely carburized to tungsten carbide at 1050°C, even though the starting temperature was 890°C. The particle was found to grow sharply before carburization.

scholarly journals Synthesis and Characterisation of Mesoporous TiO2 Nanoparticles by Novel Surfactant Assisted Sol-gel Method for the Degradation of Organic Compounds

2018 ◽  
Vol 63 (1) ◽  
pp. 85-95 ◽  
Author(s):  
Harish Phattepur ◽  
Gowrishankar Bychapur Siddaiah ◽  
Nagaraju Ganganagappa
Keyword(s):  
Electron Microscopy ◽  
Tio2 Nanoparticles ◽  
Surface Area ◽  
Sol Gel ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
Tio2 Nps ◽  
Gel Method ◽  
X Ray ◽  
Surfactant Assisted

A sol-gel method was employed to synthesise pure titanium dioxide (TiO2) and surfactant assisted TiO2 nanoparticles (NPs). The effect of novel surfactant viz., Lauryl lactyl lactate on photocatalytic properties of TiO2 was studied. TiO2 NPs were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), UV-Vis Diffuse Reflectance spectra (DRS), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermo gravimetric analysis (TGA), and Brunauer – Emmet - Teller (BET) surface area. Anatase phase of TiO2 was confirmed by X-Ray diffraction pattern and the crystallite size was between 9–19 nm. Addition of surfactant improved the BET surface area, surface defects, while the agglomeration of particles was reduced. DRS results revealed that the addition of surfactant to TiO2 sol induced a red shift of the absorption edge which resulted in the reduction of band gap from 3.23 to 3.21 eV. These physicochemical properties of TiO2 NPs were correlated with photocatalytic degradation of phenol. About 92% of phenol degradation was observed for surfactant assisted TiO2 NPs (SA-TiO2). Salicylic acid and caffeine were also degraded using SA-TiO2 NPs.

Synthesis of Nano-Barium Titanate and Application for Strontium Adsorption from Aqueous Solution

2016 ◽  
Vol 1141 ◽  
pp. 190-195
Author(s):  
Hitesh Saravaia ◽  
Hariom Gupta ◽  
Vaibhav Kulshreshtha
Keyword(s):  
Barium Titanate ◽  
Surface Area ◽  
Active Surface ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structure Morphology ◽  
Ft Ir ◽  
Tetragonal Batio ◽  
Thermal Stability Of

Barium Titanate (BaTiO3) nanostructures are synthesized by the molten salt-hydroxide reaction. The crystalline phase and chemical structure of the synthesized material are analyzed using powder x-ray diffraction (XRD) and FT-IR techniques, revealing the tetragonal BaTiO3 crystalline structure. Morphology and thermal stability of the material are characterized using TEM and TG-DTG analysis. BET surface area analysis shows significant active surface available for adsorption and its surface area value is found to be 14.8427 m2 g-1. The maximum adsorption of strontium metal is found to be 56.3 for the 1.2 g L-1 BaTiO3 adsorbent dose which reveals a remarkable separation property of the BaTiO3.

scholarly journals 2D Polymeric Network of Cu/Na, A Route for the Preparation Truncated Octahedral Catalyst Applicable in the WGS Reaction

2021 ◽  
Author(s):  
Zohreh Razmara
Keyword(s):  
Surface Area ◽  
Thermo Gravimetric Analysis ◽  
Water Gas Shift ◽  
Bet Surface Area ◽  
High Dispersion ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wgs Reaction ◽  
Water Gas

Abstract A 2D heterometallic copper(II)–sodium(I) complex based on pyridine 2,6-dicarboxylato (dipic2-) formulated as [Cu(μ-dipic)2{Na2(µ-H2O)4}]n. 2nH2O (1) has been synthesized. Thermal stability of complex 1 was studied by thermo gravimetric analysis (TGA) and differential thermal analysis (DTA). Single-crystal X-ray diffraction (SC-XRD) analysis showed that the parallelepiped colorless crystal of complex 1 crystallizes in a monoclinic system with the space group P2/c . A highly dispersed truncated octahedral catalyst formulated as Cu-Na/Al2O3 (CNM) was prepared by thermal decomposition of complex 1. Besides, the reference catalyst of Cu-Na/Al2O3 (CNR) was prepared by impregnation conventional method. The catalysts were examined by FT-IR, powder X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET) surface area, and subjected to water-gas shift (WGS) reaction in the temperature range of 150-400 °C. The catalysts showed strong surface structure-activity dependence in WGS reaction. Improved catalytic performance during the water-gas shift reaction was observed for CNM compared to CNR due to its high dispersion, smaller particle size, and higher BET specific surface area.

Preparation and Characterization of Ti0.6Cr0.4OxNy Nano-Sized Powder

2008 ◽  
Vol 368-372 ◽  
pp. 1130-1132
Author(s):  
Hong Zhi Wang ◽  
Qi Zhang ◽  
Yun Xin Gu ◽  
Yao Gang Li ◽  
Mei Fang Zhu
Keyword(s):  
Surface Area ◽  
Electron Probe ◽  
Auger Electron ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nano Powder ◽  
Transmission Electron ◽  
Cubic Structure

Ti0.6Cr0.4OxNy bimetallic metal oxynitride nano powder was synthesized by ammonolysis of the nanosized Cr2O3/TiO2 composite powder with n(Ti):n(Cr)=6:4 at 800oC for 8 h. The precursor and the resulting oxynitride were characterized by Auger electron spectroscope (AES), X-ray diffraction analysis (XRD), electron probe microanalysis (EPMA), transmission electron microscopy (TEM), and BET surface area techniques. The result indicated that the precursor was homogenous mixture of Cr2O3 and TiO2 with high BET surface area. The as-synthesized oxynitride powder contains only Ti0.6Cr0.4OxNy with cubic structure. The BET surface area of the oxynitride powder is 37.42 m2/g and the particle size is in the range of 20~30 nm.

scholarly journals Removal of Congo Red Dye using Synthesised Copper(II) Activated Carbon from Date Seeds

2021 ◽  
Vol 14 ◽  
pp. 1-9
Author(s):  
Nur rahimah Said ◽  
Hazirah Syahirah Zakria ◽  
Siti Nor Atika Baharin ◽  
Nurul' Ain Jamion
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Congo Red ◽  
Bet Surface Area ◽  
Activation Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Effective Removal ◽  
Vis Spectroscopy ◽  
Red Dye

Azo dyes are recognised as contaminants from the textile and printing industries that lead to human toxicity. Copper(II) activated carbon (CuAC) is an effective removal agent of dyes in these industries. The purpose of this study is to synthesise and characterise CuAC from date seeds. In addition, the efficiency of CuAC as a removal of Congo red (CR) in aqueous solution is also studied. Activated carbon (AC) was prepared from date seeds using phosphoric acid as activating agent, followed by activation process in a furnace at 500 ℃ for 2 hours. Copper(II) nitrate was used in the impregnation of AC to produce CuAC. The AC and CuAC were characterised using Attenuated Total Reflectance Fourier-Transform Infrared Spectroscopy (ATR-FTIR), BET surface area (SBET), Scanning Electron Microscope-Energy Dispersive X-Ray Spectroscopy (SEM-EDX), Atomic Absorption Spectroscopy (AAS) and X-Ray Diffraction (XRD). UV-VIS Spectroscopy was used to determine dye concentrations after treatment with removal agent of CuAC. The characterisation data proved that the CuAC has been successfully synthesised with 0.33% Cu(II) loaded onto AC and its surface area increased from 8.37 m2/g to 384.82 m2/g. The dye removal study was conducted at 10 ppm concentration of dye. Result revealed that 0.2 g of CuAC at pH 2 in 90 min removed 100% of CR dye.

scholarly journals Effect of Calcination Temperature on the Synthesis of ZrO2-Pillared Saponite to Catalytic Activity in Menthol Esterification

2018 ◽  
Vol 16 (1) ◽  
pp. 8 ◽  
Author(s):  
Is Fatimah ◽  
Dwiarso Rubiyanto ◽  
Nanda Candra Kartika
Keyword(s):  
Catalytic Activity ◽  
Surface Area ◽  
Calcination Temperature ◽  
Surface Acidity ◽  
Physicochemical Characteristics ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcination Temperatures ◽  
Solid Acidity

The influence of calcination temperature on the synthesis of zirconia-pillared saponite (PILS) and on its catalytic activity in menthol esterification has been studied. Zirconia pillarization was conducted using zirconium tetraisopropoxide as a precursor and with calcination temperatures of 450, 600 and 700 °C. Evaluation of physicochemical characteristics at these varied temperatures was carried out by X-Ray Diffraction (XRD), surface area analysis, Scanning Electron Eicroscope (SEM) analysis, Differential Thermal Analysis (DTA) and total acidity. The obtained results indicate that the structure and surface acidity of saponite were strongly influenced by calcination temperature. The solid acidity and surface parameters such as specific surface area, pore volume, and pore radius play an important role in the total conversion and selectivity in menthol esterification.

scholarly journals Preparation of Stellerite Loading Titanium Dioxide Photocatalyst and Its Catalytic Performance on Methyl Orange

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Hua Chen ◽  
Jianhua Wang ◽  
Huajun Wang ◽  
Fei Yang ◽  
Jia-nan Zhou ◽  
...  
Keyword(s):  
Surface Area ◽  
Sol Gel ◽  
Catalytic Performance ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
Photocatalytic Ability ◽  
X Ray ◽  
Composite Photocatalysts ◽  
Ft Ir ◽  
Better Than

TiO2/stellerite composite photocatalysts were prepared by dispersing TiO2 onto the surface of HCl, NaOH, or NaCl treated stellerite using a sol-gel method. The materials were characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDX), Fourier transform infrared spectroscopy (FT-IR), BET surface area analysis, and X-ray diffraction (XRD). HCl and NaCl modification result in the promotion of the pore formation at the stellerite surfaces and induced the microscopic changes, while the surface morphology and structure of the stellerite were almost ruined by NaOH modification. Supported TiO2 calcinated at 200°C presented anatase structure. The photocatalytic degradation activities of TiO2 loaded HCl and NaCl modified stellerite were better than that of natural stellerite, accompanied with increasing specific surface area. On the contrary, NaOH modification induced the loss of photocatalytic ability of composite due to the generation of silicates.

Sign in / Sign up

Export Citation Format

Share Document