scholarly journals Combustors with Low Emission Levels for Aero Gas Turbine Engines

2019 ◽  
Vol 4 (1) ◽  
pp. 503-514
Author(s):  
Noureddine Guellouh ◽  
Zoltán Szamosi ◽  
Zoltán Siménfalvi
Keyword(s):  
Gas Turbines ◽  
Civil Aviation ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Microphysical Properties ◽  
International Civil Aviation Organisation ◽  
Low Emission ◽  
Readiness Level ◽  
Earth’S Climate ◽  
The Impact

The aircrafts are responsible for emitting several types of pollutants, especially the pollutants in the form of NOX, CO2, CO, UHC, SOX and Particulate Matter PM (smoke/soot). The impact of aviation emissions on the global is well known, where these emissions modify the chemical and microphysical properties of the atmosphere resulting in changes of earth’s climate system, which can ultimate in critical changes in our planet fragile ecosystem, also the pollutants produced by aircraft engines cause many health problems. This is why the International Civil Aviation Organisation (ICAO) is seriously seeking to control the emission levels by issuing new standards during the successive meetings of the Committee on Aviation Environmental Protection CAEP (CAEP/01 in 1986, CAEP/2, CAEP/4, CAEP/6, CAEP/8, etc). The new regulations include more stringent standards aimed to reduce emission levels, this led to increased interest in low emission technologies. In this paper, a comprehensive review of low emissions combustion technologies for modern aero gas turbines is represented. The current low emission technologies include the high Technologies Readiness Level (TRL) including RQL, TAPS, DAC and LDI. Also, there are advanced technologies at lower TRL including LPP, ASC and VGC.

Emissions Variability and Traversing on Production RB211 Engines

1983 ◽  
Author(s):  
H. L. Hawkins ◽  
J. K. Bhangu ◽  
C. H. Priddin ◽  
P. H. Walker
Keyword(s):  
Environmental Protection Agency ◽  
Gas Turbines ◽  
Representative Sample ◽  
Gas Analysis ◽  
Civil Aviation ◽  
Probe Design ◽  
Engine Exhaust ◽  
International Civil Aviation Organisation ◽  
The Impact ◽  
Sample Transfer

In order to control the emissions from aircraft gas turbines, the International Civil Aviation Organisation (I.C.A.O.) and the U.S. Environmental Protection Agency (E.P.A.) have, through consultations with the various parties over the past decade, made firm proposals for an emission certification scheme, together with mandatory limiting levels for certain pollutants. The compliance with the proposed emission standards requires that a representative sample is collected from the engine exhaust plane and transported without changing its chemical composition to the analysis instruments. Despite clearly defined rules for sample transfer and analysis methods, the emissions measurement will be subject to variability due to the following factors: a) engine-to-engine variability which will include the impact of dimensional tolerance on the combustor hardware and other components which affect the combustor performance, b) sampling variation because of the nonuniform distribution of the pollutant species in the exhaust plane (see references 4,5), with the result that engine manufacturers are required to demonstrate “by means of detailed traverse measurements in the sampling plane” that a specific probe design provides a representative sample, and c) gas analysis instrumentation scatter that occurs in the actual analysis of identical samples.

scholarly journals The impact of physico-chemical properties of the jet fuel and biofuels on the characteristics of gas-turbine engines

2019 ◽  
Vol 22 (6) ◽  
pp. 8-16
Author(s):  
Sh. Ardeshiri
Keyword(s):  
Mathematical Model ◽  
Gas Turbine ◽  
Alternative Fuels ◽  
Gas Turbine Engine ◽  
Jet Fuel ◽  
Civil Aviation ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Engine ◽  
The Impact

The current development trend of global civil aviation is the growth of passenger and freight traffic, which entails the consumption of jet fuel. Under these conditions, increasing the efficiency of jet fuel used is of great importance. Global energy consumption is constantly growing, and, first of all, the question of diversification of oil resources arises, resources from which the bulk of motor fuels is produced. Other types of raw energy sources (natural gas, coal, bio-mass) currently account for only a small part. However, an analysis of the development of jet fuels indicates that work is underway to obtain these from other sources of raw materials, especially bio-fuels. Much attention is given to obtaining bio-fuels from renewable sources – such as algae. The issue of the mass transition of civil aviation to alternative fuels is complex and requires the solution of intricate technical as well as economic issues. One of these is the assessment of the impact of new fuels on GTE performance. It is important to give an objective and quick assessment of the use of various types of fuels on the main characteristics of the engine – i.e., throttle and high-speed characteristics. In this case, it is necessary to take into account chemical processes in the chemical composition of new types of fuel. To assess the effect of fuels on the characteristics of a gas turbine engine, it is proposed to use a mathematical model that would take into account the main characteristics of the fuel itself. Therefore, the work proposes a mathematical model for calculating the characteristics of a gas turbine engine taking into account changes in the properties of the fuel itself. A comparison is made of the percentage of a mixture of biofuels and JetA1 kerosene, as well as pure JetA1 and TC-1 kerosene. The calculations, according to the proposed model, are consistent with the obtained characteristics of a gas turbine engine in operation when using JetA1 and TC-1 kerosene. Especially valuable are the obtained characteristics of a gas turbine engine depending on a mixture of biofuel and kerosene. It was found that a mixture of biofuel and kerosene changes the physicochemical characteristics of fuel and affects the change in engine thrust and specific fuel consumption. It is shown that depending on the obtained physicochemical properties of a mixture of biofuel and kerosene, it is possible to increase the fuel efficiency and environmental friendliness of the gas turbine engines used.

scholarly journals Progress in Novel Electrodeposited Bond Coats for Thermal Barrier Coating Systems

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4214
Author(s):  
Kranthi Kumar Maniam ◽  
Shiladitya Paul
Keyword(s):  
Gas Turbine ◽  
Thermal Barrier Coating ◽  
Gas Turbines ◽  
High Performance ◽  
Turbine Engines ◽  
Thermal Barrier ◽  
Gas Turbine Engines ◽  
Potential Cost ◽  
Bond Coats ◽  
Barrier Coating

The increased demand for high performance gas turbine engines has resulted in a continuous search for new base materials and coatings. With the significant developments in nickel-based superalloys, the quest for developments related to thermal barrier coating (TBC) systems is increasing rapidly and is considered a key area of research. Of key importance are the processing routes that can provide the required coating properties when applied on engine components with complex shapes, such as turbine vanes, blades, etc. Despite significant research and development in the coating systems, the scope of electrodeposition as a potential alternative to the conventional methods of producing bond coats has only been realised to a limited extent. Additionally, their effectiveness in prolonging the alloys’ lifetime is not well understood. This review summarises the work on electrodeposition as a coating development method for application in high temperature alloys for gas turbine engines and discusses the progress in the coatings that combine electrodeposition and other processes to achieve desired bond coats. The overall aim of this review is to emphasise the role of electrodeposition as a potential cost-effective alternative to produce bond coats. Besides, the developments in the electrodeposition of aluminium from ionic liquids for potential applications in gas turbines and the nuclear sector, as well as cost considerations and future challenges, are reviewed with the crucial raw materials’ current and future savings scenarios in mind.

Design, Development and Application of Vehicle Gas Turbine Engines

1966 ◽  
Vol 181 (1) ◽  
pp. 149-172
Author(s):  
P. A. Phillips ◽  
Peter Spear
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Low Cost ◽  
Engine Performance ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Development ◽  
Turbine Engine ◽  
Wide Range ◽  
Cycle Temperature

After briefly summarizing worldwide automotive gas turbine activity, the paper analyses the power plant requirements of a wide range of vehicle applications in order to formulate the design criteria for acceptable vehicle gas turbines. Ample data are available on the thermodynamic merits of various gas turbine cycles; however, the low cost of its piston engine competitor tends to eliminate all but the simplest cycles from vehicle gas turbine considerations. In order to improve the part load fuel economy, some complexity is inevitable, but this is limited to the addition of a glass ceramic regenerator in the 150 b.h.p. engine which is described in some detail. The alternative further complications necessary to achieve satisfactory vehicle response at various power/weight ratios are examined. Further improvement in engine performance will come by increasing the maximum cycle temperature. This can be achieved at lower cost by the extension of the use of ceramics. The paper is intended to stimulate the design application of the gas turbine engine.

Determination of Cycle Configuration of Gas Turbines and Aircraft Engines by Optimization Procedure

1990 ◽  
Author(s):  
Yoshiharu Tsujikawa ◽  
Makoto Nagaoka
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Specific Impulse ◽  
Optimization Procedure ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Aircraft Engines ◽  
Scramjet Engine ◽  
Aero Engines

This paper is devoted to the analyses and optimization of simple and sophisticated cycles, particularly for various gas turbine engines and aero-engines (including scramjet engine) to achive the maximum performance. The optimization of such criteria as thermal efficiency, specific output and total performance for gas turbine engines, and overall efficiency, non-dimensional thrust and specific impulse for aero-engines have been performed by the optimization procedure with multiplier method. The comparisons of results with analytical solutions establishes the validity of the optimization procedure.

scholarly journals Inlet Air Fogging of Marine Gas Turbine in Power Output Loss Compensation

2015 ◽  
Vol 22 (4) ◽  
pp. 53-58 ◽  
Author(s):  
Zygfryd Domachowski ◽  
Marek Dzida
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Evaporative Cooling ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Output Loss ◽  
Direct Evaporative Cooling ◽  
Loss Compensation ◽  
The World

Abstract The use of inlet air fogging installation to boost the power for gas turbine engines is widely applied in the power generation sector. The application of fogging to mechanical drive is rarely considered in literature [1]. This paper will cover some considerations relating to its application for gas turbines in ship drive. There is an important evaporative cooling potential throughout the world, when the dynamic data is evaluated, based on an analysis of coincident wet and dry bulb information. This data will allow ships’ gas turbine operators to make an assessment of the economics of evaporative fogging. The paper represents an introduction to the methodology and data analysis to derive the direct evaporative cooling potential to be used in marine gas turbine power output loss compensation.

Development of a Lean-Premixed Two-Stage Annular Combustor for Gas Turbine Engines

1994 ◽  
Author(s):  
Fred C. Bahlmann ◽  
B. Martien Visser
Keyword(s):  
Gas Turbine ◽  
Turbine Engines ◽  
Emission Characteristics ◽  
Gas Turbine Engines ◽  
Two Stage ◽  
Low Emission ◽  
Lean Premixed ◽  
Annular Combustor

The development, from concept to hardware of a lean-premixed two-stage combustor for small gas turbine engines is presented. This Annular Low Emission Combustor (ALEC) is based on a patent of R.J. Mowill. Emission characteristics of several prototypes of this combustor under a variety of conditions are presented. It is shown that ultra-low NOx levels (< 10 ppm) can be reached with satisfactory CO levels (< 50 ppm).

scholarly journals Single-Coil Eddy Current Sensors and Their Application for Monitoring the Dangerous States of Gas-Turbine Engines

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 2107 ◽  
Author(s):  
Sergey Borovik ◽  
Yuriy Sekisov
Keyword(s):  
Gas Turbine ◽  
Eddy Current ◽  
Natural Aging ◽  
Turbine Engines ◽  
Radial Clearance ◽  
Gas Turbine Engines ◽  
Structural Elements ◽  
Single Coil ◽  
The Impact ◽  
Blade Tips

The creation and exploitation of gas turbine engines (GTE) often involve two mutually exclusive tasks related to ensuring the highest reliability while achieving a good economic and environmental performance of the power plant. The value of the radial clearance between the blade tips of the compressor or turbine and the stator is a parameter that has a significant impact on the efficiency and safety of the GTE. However, the radial displacements that form tip clearances are only one of the components of the displacements made by GTE elements due to the action of power loads and thermal deformations during engines’ operation. The impact of loads in conjunction with natural aging is also the reason for the wear of the GTE’s structural elements (for example, bearing assemblies) and the loss of their mechanical strength. The article provides an overview of the methods and tools for monitoring the dangerous states of the GTE (blade tips clearances, impellers and shafts displacements, debris detecting in lubrication system) based on the single-coil eddy current sensor, which remains operational at the temperatures above 1200 °C. The examples of practical application of the systems with such sensors in bench tests of the GTE are given.

Inlet Fogging of Gas Turbine Engines: Part B — Fog Droplet Sizing Analysis, Nozzle Types, Measurement and Testing

2002 ◽  
Author(s):  
Mustapha Chaker ◽  
Cyrus B. Meher-Homji ◽  
Thomas Mee
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Measurement Techniques ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Size Measurement ◽  
The Past ◽  
Testing Method ◽  
Measurement And Testing ◽  
Experimental And Theoretical Studies

The inlet fogging of gas turbine engines for power augmentation has seen increasing application over the past decade yet not a single technical paper treating the physics and engineering of the fogging process, droplet size measurement, droplet kinetics, or the duct behavior of droplets, from a gas turbine perspective, is available. This paper provides the results of extensive experimental and theoretical studies conducted over several years, coupled with practical aspects learned in the implementation of nearly 500 inlet fogging systems on gas turbines ranging in power from 5 to 250 MW. Part B of the paper treats the practical aspects of fog nozzle droplet sizing, measurement and testing presenting the information from a gas turbine fogging perspective. This paper describes the different measurement techniques available, covers design aspects of nozzles, provides experimental data on different nozzles and provides recommendations for a standardized nozzle testing method for gas turbine inlet air fogging.

Sign in / Sign up

Export Citation Format

Share Document