scholarly journals Сверхширокополосный генератор хаотических колебаний микроволнового диапазона с дополнительным нелинейным контуром

2019 ◽  
Vol 45 (23) ◽  
pp. 51
Author(s):  
Н.А. Максимов
Keyword(s):  
Experimental Study ◽  
Active Element ◽  
Ultra Wideband ◽  
60 Ghz ◽  
Chaotic Oscillations ◽  
Frequency Range ◽  
Nonlinear Circuit ◽  
Lumped Element

A possibility of generating ultra-wideband chaotic oscillations in the frequency range up to 60 GHz using a bipolar SiGe heterotransistor is shown. The upper frequency boundary is determined by the cut-off frequency of the active element of the generator. Such a possibility is provided by means of adding a nonlinear circuit into the oscillator layout, in which chaotic oscillations can develop up to the specified frequency. The results of an experimental study of a lumped-element version of the oscillator are presented.

60 GHz-Band Low-Noise Amplifier

2017 ◽  
Vol 26 (05) ◽  
pp. 1750075 ◽  
Author(s):  
Najam Muhammad Amin ◽  
Lianfeng Shen ◽  
Zhi-Gong Wang ◽  
Muhammad Ovais Akhter ◽  
Muhammad Tariq Afridi
Keyword(s):  
Transmission Line ◽  
Quality Factor ◽  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Constant Current ◽  
60 Ghz ◽  
Frequency Range ◽  
Constant Current Density ◽  
Chip Area

This paper presents the design of a 60[Formula: see text]GHz-band LNA intended for the 63.72–65.88[Formula: see text]GHz frequency range (channel-4 of the 60[Formula: see text]GHz band). The LNA is designed in a 65-nm CMOS technology and the design methodology is based on a constant-current-density biasing scheme. Prior to designing the LNA, a detailed investigation into the transistor and passives performances at millimeter-wave (MMW) frequencies is carried out. It is shown that biasing the transistors for an optimum noise figure performance does not degrade their power gain significantly. Furthermore, three potential inductive transmission line candidates, based on coplanar waveguide (CPW) and microstrip line (MSL) structures, have been considered to realize the MMW interconnects. Electromagnetic (EM) simulations have been performed to design and compare the performances of these inductive lines. It is shown that the inductive quality factor of a CPW-based inductive transmission line ([Formula: see text] is more than 3.4 times higher than its MSL counterpart @ 65[Formula: see text]GHz. A CPW structure, with an optimized ground-equalizing metal strip density to achieve the highest inductive quality factor, is therefore a preferred choice for the design of MMW interconnects, compared to an MSL. The LNA achieves a measured forward gain of [Formula: see text][Formula: see text]dB with good input and output impedance matching of better than [Formula: see text][Formula: see text]dB in the desired frequency range. Covering a chip area of 1256[Formula: see text][Formula: see text]m[Formula: see text]m including the pads, the LNA dissipates a power of only 16.2[Formula: see text]mW.

scholarly journals A computationally efficient hybrid 2D–3D subwoofer model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ahmad H. Bokhari ◽  
Martin Berggren ◽  
Daniel Noreland ◽  
Eddie Wadbro
Keyword(s):  
Hybrid Model ◽  
3D Model ◽  
Element Model ◽  
Acoustic Properties ◽  
Computational Time ◽  
Average Response ◽  
Frequency Range ◽  
Computationally Efficient ◽  
Lumped Element ◽  
Lumped Element Model

AbstractA subwoofer generates the lowest frequency range in loudspeaker systems. Subwoofers are used in audio systems for live concerts, movie theatres, home theatres, gaming consoles, cars, etc. During the last decades, numerical simulations have emerged as a cost- and time-efficient complement to traditional experiments in the design process of different products. The aim of this study is to reduce the computational time of simulating the average response for a given subwoofer design. To this end, we propose a hybrid 2D–3D model that reduces the computational time significantly compared to a full 3D model. The hybrid model describes the interaction between different subwoofer components as interacting modules whose acoustic properties can partly be pre-computed. This allows us to efficiently compute the performance of different subwoofer design layouts. The results of the hybrid model are validated against both a lumped element model and a full 3D model over a frequency band of interest. The hybrid model is found to be both accurate and computationally efficient.

scholarly journals Band notched self complementaryultra wideband antenna for wireless applications

2018 ◽  
Vol 7 (2.8) ◽  
pp. 529 ◽  
Author(s):  
Ch Ramakrishna ◽  
G A.E.Satish Kumar ◽  
P Chandra Sekhar Reddy
Keyword(s):  
High Frequency ◽  
Return Loss ◽  
Wide Band ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Relative Dielectric Permittivity ◽  
Frequency Range ◽  
Ground Structure ◽  
Wireless Applications ◽  
Patch Edge

This paper presents a band notched WLAN self complementaryultra wide band antenna for wireless applications. The proposed antenna encounters a return loss (RL) less than -10dB for entire ultra wideband frequency range except band notched frequency. This paper proposes a hexagon shape patch, edge feeding, self complementary technique and defective ground structure. The antenna has an overall dimensionof 28.3mm × 40mm × 2mm, builton  substrate FR4 with a relative dielectric permittivity 4.4. And framework is simulated finite element method with help of high frequency structured simulator HFSSv17.2.the proposed antenna achieves a impedance bandwidth of 8.6GHz,  band rejected WLAN frequency range 5.6-6.5 GHz with  vswr is less than 2.

scholarly journals A Compact Four-Port Coplanar Antenna Based on an Excitation Switching Reconfigurable Mechanism for Cognitive Radio Applications

2019 ◽  
Vol 9 (15) ◽  
pp. 3157 ◽  
Author(s):  
O ◽  
Jin ◽  
Choi
Keyword(s):  
Cognitive Radio ◽  
High Frequency ◽  
Coplanar Waveguide ◽  
Low Frequency ◽  
Loop Antenna ◽  
Ultra Wideband ◽  
Frequency Range ◽  
Uwb Antenna ◽  
High Isolation ◽  
Loop Antennas

In this paper, we propose a compact four-port coplanar antenna for cognitive radio applications. The proposed antenna consists of a coplanar waveguide (CPW)-fed ultra-wideband (UWB) antenna and three inner rectangular loop antennas. The dimensions of the proposed antenna are 42 mm × 50 mm × 0.8 mm. The UWB antenna is used for spectrum sensing and fully covers the UWB spectrum of 3.1–10.6 GHz. The three loop antennas cover the UWB frequency band partially for communication purposes. The first loop antenna for the low frequency range operates from 2.96 GHz to 5.38 GHz. The second loop antenna is in charge of the mid band from 5.31 GHz to 8.62 GHz. The third antenna operates from 8.48 GHz to 11.02 GHz, which is the high-frequency range. A high isolation level (greater than 17.3 dB) is realized among the UWB antenna and three loop antennas without applying any additional decoupling structures. The realized gains of the UWB antenna and three loop antennas are greater than 2.7 dBi and 1.38 dBi, respectively.

Design of an interlocked four-port MIMO antenna for UWB automotive communications

2021 ◽  
pp. 1-8
Author(s):  
M. Saravanan ◽  
R. Kalidoss ◽  
B. Partibane ◽  
K. S. Vishvaksenan
Keyword(s):  
Multiple Input Multiple Output ◽  
Performance Estimation ◽  
Ultra Wideband ◽  
Antenna Element ◽  
Frequency Range ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Operating Bandwidth ◽  
Peak Gain

Abstract The design, analysis, fabrication, and testing of a four-port multiple-input multiple-output (MIMO) antenna is reported in this paper for automotive communications. The MIMO antenna is constructed using the basic antenna element exploiting a slot geometry. Two such antennas are developed on the same microwave laminate to develop a two-port MIMO antenna. Two such microwave laminates are interlocked to create the four-port MIMO scheme. The most distinct feature of the proposed architecture is that the inter-port isolation is well-taken care without the need for an external decoupling unit. The four-port MIMO antenna has an overall volume of 32 × 15 × 32 mm3. The prototype MIMO antenna is fabricated and the measurements are carried out to validate the simulation results. The antenna offers ultra-wideband (UWB) characteristics covering the frequency range of 2.8–9.5 GHz. The average boresight gain of the antenna ranges from 3.2 to 5.41 dBi with the peak gain at 8 GHz. The simulated efficiency of the antenna is greater than 73% within the operating bandwidth. The MIMO parameters such as envelope correlation coefficient, diversity gain, and mean effective gain are evaluated and presented. The appropriateness of the proposed antenna for deployment in the shark fin housing of the present-day automobiles is verified using on-car performance estimation.

scholarly journals A Circular Disc Microstrip Antenna with Dual Notch Band for GSM/Bluetooth and Extended UWB Applications

2018 ◽  
Vol 7 (2.16) ◽  
pp. 11
Author(s):  
Sanjeev Kumar ◽  
Ravi Kumar ◽  
Rajesh Kumar Vishwakarma
Keyword(s):  
Radiation Pattern ◽  
Microstrip Antenna ◽  
Ground Plane ◽  
Circular Disc ◽  
Ultra Wideband ◽  
Resonant Circuit ◽  
Frequency Range ◽  
Notch Band ◽  
Uwb Applications ◽  
Ku Band

A microstrip antenna with a circular disc design and modified ground is proposed in this paper. Circular shapes of different size have been slotted out from the radiating patch for achieving extended ultra wideband (UWB) with GSM/Bluetooth bands with maximum bandwidth of 17.7 GHz (0.88-18.6 GHz). Further, characteristic of dual notch band is achieved, when a combination of T and L-shaped slots are etched into the circular disc and ground plane respectively. Change in length of slots is controlling the notch band characteristics. The proposed antenna has rejection bandwidth of 1.3-2.2 GHz (LTE band), 3.2-3.9 GHz (WiMAX band) and 5.2-6.1 GHz (WLAN band) respectively. It covers the frequency range of 0.88-18.5 GHz with the VSWR of less than 2. Also, an equivalent parallel resonant circuit has been demonstrated for band notched frequencies of the designed antenna. The gain achieved by the proposed antenna is 6.27 dBi. This antenna has been designed, investigated and fabricated for GSM, Bluetooth, UWB, X and Ku band applications. The stable gain including H & E-plane radiation pattern with good directivity and omnidirectional behavior is achieved by the proposed antenna. Measured bandwidths are 0.5 GHz, 0.8 GHz, 1.1 GHz and 11.7 GHz respectively. 

scholarly journals Модель хаотической автоколебательной системы диапазона 10-30 GHz на основе SiGe-технологии 130 nm

2018 ◽  
Vol 44 (9) ◽  
pp. 26
Author(s):  
Е.В. Ефремова
Keyword(s):  
Silicon Germanium ◽  
Communication Systems ◽  
Chaotic Oscillations ◽  
Frequency Range ◽  
Process Technology ◽  
Fifth Generation ◽  
Generator Model

AbstractThe problem of generation of utlrawideband chaotic oscillations in the frequency range of 10–30 GHz is considered. This problem is relevant to fifth-generation communication systems. A generator model designed for the silicon–germanium 130-nm process technology is proposed and studied.

Sign in / Sign up

Export Citation Format

Share Document