scholarly journals Synthesis and Characterization of Titania-Rice Husk Silica Composites as Photocatalyst

2015 ◽  
Vol 15 (1) ◽  
pp. 36-42 ◽  
Author(s):  
Posman Manurung ◽  
Rudy Situmeang ◽  
Ediman Ginting ◽  
Indra Pardede
Keyword(s):  
Rice Husk ◽  
Sol Gel ◽  
Bet Surface Area ◽  
Synthesis And Characterization ◽  
Ultraviolet Rays ◽  
X Ray Diffraction ◽  
Titanium Butoxide ◽  
X Ray ◽  
Scanning Electron

This article describes the synthesis of titania-silica composites by a sol-gel method using a mixture of silica of rice husk and titanium butoxide sols. Microstructures were examined at calcination temperature in the range of 500 to 700 °C, with temperatures interval of 50 °C. The sintered catalysts were subsequently tested for photodegradation of methylene blue (MB) under ultraviolet and sunlight rays. Physical characteristics were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM)/energy dispersive X-ray spectroscopy (EDS), and Brunauer-Emmett-Teller (BET). The XRD results did not show the presence of silica crystal phase in each sample. The results showed that the highest BET surface area of samples was obtained at the temperature of 650 °C. In sample calcined 500 °C, the activity of the catalyst on MB was relatively similar in both sunlight and ultraviolet rays.

scholarly journals Synthesis and characterization of Ln-123 superconductors

2008 ◽  
Vol 73 (4) ◽  
pp. 479-486 ◽  
Author(s):  
Arturas Zalga ◽  
Remigijus Juskenas ◽  
Algirdas Selskis ◽  
Darius Jasaitis ◽  
Aivaras Kareiva
Keyword(s):  
Electron Microscopy ◽  
Sol Gel ◽  
Melting Process ◽  
Oxygen Stoichiometry ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Superconducting Compounds ◽  
Scanning Electron

A sol-gel method was applied to prepare precursors for NdBa2Cu3O7-x (Nd-123) and SmBa2Cu3O7-x (Sm-123) superconducting compounds. The sintered products were examined by X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). The powders sintered at 950 and 1000 ?C showed the formation of monophasic Nd-123 and Sm-123 superconductors. The formation of Nd-123 and Sm-123 phases from the sol-gel derived precursors at higher temperatures (1050 and 1100 ?C), however, did not proceed due to the melting process. The correlation between the TC for different lanthanides (Ln Ho, Nd and Sm) in the Ln-123 compound and orthorhombicity and oxygen stoichiometry were also estimated.

Synthesis and Characterization of Ag-TiO2 Nanocomposites for Possible Use as Biocide

2017 ◽  
Vol 899 ◽  
pp. 212-215
Author(s):  
Paula de Freitas Rosa ◽  
Ana Clara Matias Alves ◽  
Mônica Lopes Aguiar ◽  
André Bernardo
Keyword(s):  
Sodium Citrate ◽  
Titanium Dioxide Nanoparticles ◽  
Sol Gel ◽  
Nanocomposite Materials ◽  
Reduction Reaction ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Titanium Butoxide ◽  
X Ray

Currently nanoparticles are being widely used because they have large surface area and pronounced effect relative to the properties of the material. Silver and Titanium Dioxide nanoparticles, for example, have pronounced biocidal effects, since they can inactivate certain enzymes and alter the DNA synthesis of some microorganisms. It is expected that a composite of the nanoparticles of the two metals can further increase the biocide power. This way, the study of the synthesis and characterization of nanocomposites becomes highly relevant. The aim of this work was to synthesize Ag-TiO2 nanocomposites and to characterize them in order to contribute to the understanding of the preparation of nanocomposite materials. In this study, we used a sol-gel method, which makes use of a reduction reaction using sodium citrate as the reducing agent, and titanium butoxide, acetic acid and silver nitrate as starting material. After being synthesized, the nanocomposite was analyzed with the techniques of Scanning Electron Microscopy coupled to energy dispersive X-ray detector (SEM / EDS) and X-ray Diffraction.

SYNTHESIS AND CHARACTERIZATION OF Y2SiO5:Ce3+ PHOSPHOR MATERIALS BY SOL–GEL PROCESS

2010 ◽  
Vol 17 (01) ◽  
pp. 59-62 ◽  
Author(s):  
YOUNG-JAE KO ◽  
JONG KYU LEE ◽  
MIN-CHEOL CHU ◽  
DONG-SIK BAE
Keyword(s):  
Electron Microscopy ◽  
Sol Gel ◽  
Synthesis And Characterization ◽  
Luminescence Spectra ◽  
Photoluminescence Spectra ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sol Gel Process ◽  
Scanning Electron

Y 2 SiO 5: Ce 3+ particles was synthesized by sol–gel process. In all samples treated at 1100°C, monoclinic X 1 phase for all cerium concentration. Luminescence spectra shows broad Ce 3+ luminescence in Y 2 SiO 5 host, which picks around 450 nm. The synthesized and calcined powders were characterized by thermogravimetry-differential scanning calorimeter (TG-DSC), X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and photoluminescence spectra (PL).

scholarly journals Karakteristik Struktur Mikro Komposit Aspal Silika Sekam Padi Dengan Variasi Komposisi (20%:80%, 15%:85% dan 10%:90%)

2020 ◽  
Vol 1 (2) ◽  
pp. 58-63
Author(s):  
Qori Sari Dewi ◽  
◽  
Simon Sembiring ◽  
Syafriadi Syafriadi ◽  
Ediman Ginting ◽  
...  
Keyword(s):  
Rice Husk ◽  
Sol Gel ◽  
Synthesis And Characterization ◽  
Rice Husks ◽  
X Ray Diffraction ◽  
X Ray ◽  
Average Grain Size ◽  
Materials Used ◽  
Silica Synthesis

Synthesis and characterization of rice husk and asphalt silica composites with various compositions have been carried out 20%: 80%, 15%: 85% and 10%: 90%. Silica synthesis from rice husk wa carried out using the sol-gel method. The materials used are rice husks, solid asphalt, distilled water, gasoline, NaOH and HNO3. This research was conducted of variations in the composition the effect of silica and asphalt on the microstructure and structure of the sample. The characterization results of Scanning Electron Microscopy and Energy Dispersive Spectroscopy (SEM-EDS) on the surface of silica asphalt composites in the form of erratic clots and cracks on the surface of the sample with an average grain size of 3.483 µm, 8,127 µm, and 7,192 µm. The analysis EDS results in the elements content contained in the sample elements of carbon (C), silicon (Si), oxygen (O), a little element of sulfur (S) and aluminum (Al). Then, the results of the X-Ray Diffraction (XRD) characterization obtained the structure of amorphous silica and amorphous carbon.

Hydrothermal Synthesis and Characterization of BiFeO3 Polyhedral Crystallites

2012 ◽  
Vol 174-177 ◽  
pp. 508-511
Author(s):  
Lin Lin Yang ◽  
Yong Gang Wang ◽  
Yu Jiang Wang ◽  
Xiao Feng Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

BiFeO3 polyhedrons had been successfully synthesized via a hydrothermal method. The as-prepared products were characterized by power X-ray diffraction (XRD) pattern, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The possible mechanisms for the formation of BiFeO3 polyhedrons were discussed. Though comparison experiments, it was found that the kind of precursor played a key role on the morphology control of BiFeO3 crystals.

Rapid Synthesis and Characterization of CuInS2 Prepared Using Microwave-Assisted Heating

2015 ◽  
Vol 775 ◽  
pp. 143-146
Author(s):  
Ming Kwen Tsai ◽  
Yueh Chien Lee ◽  
Chia Chih Huang ◽  
Sheng Yao Hu ◽  
Kwong Kau Tiong ◽  
...  
Keyword(s):  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
Rapid Synthesis ◽  
X Ray ◽  
Sem Image ◽  
Microwave Assisted ◽  
Calcination Treatment ◽  
Scanning Electron

In this work, the CuInS2 nanoparticles are successfully synthesized by microwave-assisted heating technique and further calcined at 400 °C. The morphological, structural, and optical properties of the synthesized CuInS2 nanoparticles are investigated by scanning electron microscope (SEM), X-ray diffraction (XRD), Raman scattering, and transmittance measurement, respectively. The SEM image shows the clear particle shape of the calcined CuInS2 nanoparticles. After calcination treatment, the fundamental (112) peak of the XRD spectrum and a broad Raman peak mixed with chalcopyrite and CuAu structures support the improved crystallinity of the calcined CuInS2 nanoparticles.

scholarly journals Synthesis and characterization of apatite silicated powders with wet precipitation method

2021 ◽  
Vol 234 ◽  
pp. 00106
Author(s):  
Houda Labjar ◽  
Hassan Chaair
Keyword(s):  
Electron Microscopy ◽  
Heat Treatment ◽  
Analytical Techniques ◽  
Precipitation Method ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wet Precipitation ◽  
Scanning Electron

The synthesis of apatite silicated Ca10(PO4)6-x(SiO4)x(OH)2-x (SiHA) with 0≤x≤2 was investigated using a wet precipitation method followed by heat treatment using calcium carbonate CaCO3 and phosphoric acid H3PO4 and silicon tetraacetate SiC8H20O4 (TEOS) in medium of water ethanol, with three different silicate concentrations. After drying, the samples are ground and then characterized by different analytical techniques like X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Scanning electron Microscopy (SEM) and chemical analysis.

Synthesis and Characterization of the PANI/ITO Conducting Nanocomposites

2010 ◽  
Vol 663-665 ◽  
pp. 542-545 ◽  
Author(s):  
Bing Jie Zhu ◽  
Xin Wei Wang ◽  
Mei Fang Zhu ◽  
Qing Hong Zhang ◽  
Yao Gang Li ◽  
...  
Keyword(s):  
Doping Concentration ◽  
In Situ Polymerization ◽  
Synthesis And Characterization ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Conductivity ◽  
Scanning Electron

The PANI/ITO conducting nanocomposites have been synthesized by in-situ polymerization. The obtained nanocomposites were characterized by X-ray diffraction pattern, scanning electron microscopy and Fourier transform infrared. Electrical conductivity measurements on the samples pressed into pellets showed that the maximum conductivity attained 2.0 ± 0.05 S/cm for PANI/ITO nanocomposites, at ITO doping concentration of 10 wt%. The results of the present work may provide a simple, rapid and efficient approach for preparing PANI/ITO nanocomposites.

Synthesis and characterization of homogeneous lead-substituted tin oxide with the (110) face of rutile structure

2000 ◽  
Vol 15 (10) ◽  
pp. 2076-2079
Author(s):  
Chika Nozaki ◽  
Takashi Yamada ◽  
Kenji Tabata ◽  
Eiji Suzuki
Keyword(s):  
Electron Microscopy ◽  
Tin Oxide ◽  
Photoelectron Spectroscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Rutile Structure ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Synthesis of a rutile-type lead-substituted tin oxide with (110) face was investigated. The characterization was performed by x-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive x-ray spectroscopy, infrared spectroscopy, x-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller surface area measurements. The homogeneous rutile-type lead-substituted tin oxide was obtained until 4.1 mol% of tin was substituted with lead. The surface of obtained oxide had a homogeneously lead-substituted (110) face.

Synthesis and Characterization of Y2O3 Nanoflowers

2012 ◽  
Vol 465 ◽  
pp. 76-79 ◽  
Author(s):  
Shuang Zhan ◽  
Xia Li
Keyword(s):  
Fourier Transform ◽  
Phase Composition ◽  
Electron Microscope ◽  
Synthesis And Characterization ◽  
The Novel ◽  
X Ray Diffraction ◽  
Facile Hydrothermal Method ◽  
X Ray ◽  
Scanning Electron

The novel Y2O3 nanoflowers were synthesized through a facile hydrothermal method without using any catalyst or template. The phase composition and the microstructure of as-prepared products were characterized by field emission scanning electron microscope (FE-SEM), X-ray diffraction (XRD) as well as Fourier transform infrared spectrum. The formation mechanism for the Y2O3 flowers has been proposed.

Sign in / Sign up

Export Citation Format

Share Document