Rancang Bangun Prototipe Keamanan Ruang Laboratorium dengan Pintu Otomatis Menggunakan Sensor Suhu MLX90614 Berbasis Arduino Atmega 2560

Research on laboratory room security system has begun to be developed with various kinds of inputs used. In this study, the design of a laboratory room security prototype with automatic doors has been realized using the MLX90614 temperature sensor based on Arduino Atmega 2560. The design of this prototype aims to design a prototype laboratoey room with automatic doors using a door lock solenoid and a temperature sensor MLX90614. In addition, this system is equipped with a counter to reduce and add people in the room using the FC-51 infrared sensor. Data retrieval is done by detecting human temperature before entering the room, when the temperature input is met, the door of the room will open with a maximum limit of 10 people. The results showed that the system was functioning properly, indicated by the state of the door that could open when it received an input of temperature between 35-37°C, the door remained closed when detecting of temperature other than 35-37°, and the door remained closed when the object in the room was up to 10 people.

Analisis Jembatan Garam Campuran Alumina dan Kalsium Karbonat pada Karakteristik Elektrik Pembangkit Listrik Sel Galvanis dengan Elektrolit Air Laut

Penelitian ini dilakukan untuk menganalisis pengaruh variasi konsentrasi campuran jembatan garam terhadap karakteristik elektrik 5 buah sel galvanis seri menggunakan elektroda Cu(Ag)-Zn dengan beban 20 LED. Variasi konsentrasi campuran jembatan garam menggunakan alumina 0,1 dan 1 mol, kalsium karbonat 0,1 dan 1 mol pada semen dengan menggunakan air laut sebagai pelarut. Monitoring tegangan dan arus pada sel galvanis menggunakan sensor INA219 sedangkan monitoring intensitas cahaya menggunakan sensor BH1750 secara real-time. Hasil penelitian menunjukkan bahwa semakin besar konsentrasi alumina pada jembatan garam akan semakin besar nilai tegangan yang dihasilkan. Nilai hambatan dalam sel galvanis akan semakin kecil apabila konsentrasi jembatan garam kalsium karbonat memiliki nilai kecil.

Analisis Pertumbuhan Fase Superkonduktor BSCCO-2212 dan BPSCCO-2212 Akibat Variasi Suhu Sintering Menggunakan Metode Pencampuran Basah

The research was conducted to determine the effect of sintering temperature on the level of purity of the superconducting phase BSCCO-2212 and BPSCCO-2212 using the wet mixing method. Sintering was carried out for 20 hours with variations in sintering temperature: 825, 830, 835 and 840°C. XRD results showed that the phase purity level increased until it reached the optimum point at 835°C sintering temperature and then decreased at 840°C. The highest volume fraction of the BSCCO-2212 sample was obtained at a sintering temperature of 835°C at 71.09% and the highest degree of orientation was obtained at a sintering temperature of 830°C at 26.44%. In the BPSCCO-2212 sample, the highest volume fraction was obtained at a sintering temperature of 835°C at 52.59% and the highest degree of orientation at a sintering temperature of 830°C at 43.49%. The results of the comparison of BSCCO-2212 and BPSCCO-2212 samples showed that the BPSCCO-2212 sample had a higher level of phase purity than BSCCO-2212.

Rancang Bangun Mesin Penggulung Lilitan Kawat Transformator Otomatis Berbasis Arduino Uno

Research on application of the design an Arduino Uno-based automatic transformer wire winding machine has been carried out. The research aim was to make an automatic winding machine using wire coils that can be adjusted for rotation speed and high accuracy of the number of turns. In testing system, the enamel wire was wrapped around with a different number of turns, that is 200;400;600;800;1000 turns. The calibration method in this study was carried out manually, that is recounting the turns on the koker that had been wrapped using an automatic winding machine. The speed of the winding machine is calibrated using a tachometer. The results of the calculation of the average rolling accuracy of 99,73%.

Perancangan Simulasi Hardware-in-The-Loop Untuk Sistem Manajemen Baterai

In a Microgrid system that relies on renewable energy generation, one of the most important constituent systems is the Battery Energy Storage System because of its vital role in maintaining the stability of the Microgrid in providing power to the load. However, to operate the battery, a Battery Management System is needed to ensure the battery operates at the desired working range, so that battery reliability can be maintained. To determine the behavior of the Microgrid and the designed BMS in accordance with the desired specifications, a Hardware-inthe-Loop (HIL) Simulation has been designed using Simulink to model a DC Microgrid which consists of several sub-systems such as: An ideally designed generator and load as a tester, a bidirectional buck and boost converter with a PI controller, and a battery system equipped with a Switched Shunt Resistor Cell Balancing type, all controlled using the BMS algorithm implemented on Arduino. From the test results, it is found that HIL can communicate with good QoS on various inputs as long as the Arduino sample time meets. Then the PI controller with HIL was able to improve converter performance and also succeeded in controlling cell balancing with the efficiency of charging and idle modes of 99% and 99.4% respectively. Finally, in testing the integrated system, the BMS can maintain the performance of the Microgrid with bus voltage and battery current parameters in various SoC conditions and generator voltage fluctuations, even though there are high voltage transients.

Kajian Simulasi Dinamika Molekul Adsorpsi Hidrogen pada Carbone Nanotube dengan Variasi Chirality dan Temperatur Menggunakan Kode LAMMPS

Hydrogen adsorption has been simulated on carbon nanotubes for optimum hydrogen absorption. Parameters that affect the amount of hydrogen absorbed have been studied, such as the effect of chirality and temperature on hydrogen absorption in CNTs. The simulation method of hydrogen adsorption on carbone nanotubes uses molecular dynamics simulation code LAMMPS, applies Lennard-Jones interatomic potential and hydrogen atom movement using Van Der Waals force with Microcanonical Ensemble. Data analysis is the output of LAMPS in the form of data in XYZ format. The data contains information in the form of integration steps, number of atoms, temperature, pressure, potential energy, kinetic energy, volume, van der Waals energy, total simulation time and hydrogen absorption. The simulation results show that the optimum absorption occurs at run 10000 and a temperature of 100 K, for armchair chirality of 10 atoms, chirality of 12 atoms and zigzag chrality of 5 atoms. Formation of hydrogen coordinates with Avogadro software, formation of CNT coordinates with VMD software and visualization of hydrogen adsorption on CNTs using VMD software.

Rancang Bangun Alat Ukur Kekeruhan Air Menggunakan Fototransistor dan LED Inframerah Berbasis Arduino Uno

In this research, the water turbidity measurement tool based on Arduino Uno has been designed and built using phototransistors and infrared LEDs. This measuring instrument consists of a series of infrared sensors, Arduino as a process, LCD I2C as a value viewer, Micro SD as a data storage, and RTC as a timer. This study used two water samples with various concentrations. The sample used, namely distilled water plus impurities in the form of soil and ash. The distilled water used is still 100 ml with variations in the concentration of impurities ranging from 0,1-0,9 gr. Sensor test results show that the greater the turbidity level, the greater the voltage obtained. Sensor scanning ranges from 2,02 V-4,00 V for groundwater and 2,02 V-4,31 V for ash water. The reading uses a standard measuring instrument for groundwater ranging from 0 NTU to 331,4 NTU, while for ash water ranging from 0 NTU to 284,4 NTU. Data from the sensor test results in an equation used to convert the artificial measuring instrument's voltage value into a turbidity value. Then, data is taken using the same sample, so groundwater's turbidity value was obtained from 0 NTU to 318,94 NTU while for ash water from 0 NTU to 285,13 NTU. Based on the results, average accuracy for water was obtained. Soil amounted to 94,66%, while for ash water was 96,63%.

Pengaruh Variasi Polivinilpirolidon (PVP) Terhadap Pembentukan Serat Nano TiO2 Menggunakan Metode Electrospinning

Research on the formation of TiO2 nanofiber has been carried out with PVP variations of 1.1; 1,2; 1.3; 1.4 and 1.5 grams using electrospinning. This study aims to determine the effect of PVP variation on the viscosity and morphology of TiO2 nanofibers and to determine the crystal structure of the fibers. Synthesis of TiO2 was carried out using the sol-gel method. TTIP is used as a precursor, ethanol as a solvent, acetic acid as a catalyst and PVP as a fiber-forming polymer. The results of the viscosity measurement show that the amount of PVP used in the sample is directly proportional to the level of solution viscosity. Based on the results of SEM characterization, it showed relatively uniform nanofiber morphology with fiber diameter ranging from 94 nm - 735 µm. The results of TEM characterization showed that the size of TiO2 nanofiber particles ranged from 7-15 nm. The results of XRD analysis showed that the crystal structures formed at a calcination temperature of 450 oC were the anatase and rutile phases.

Sistem Identifikasi Tingkat Kematangan Buah Nanas Secara Non-Destruktif Berbasis Computer Vision

A computer vision-based non-destructive pineapple maturity level identification system has been realized. This research was conducted to create a system capable of identifying six indexes of pineapple maturity level. An artificial neural network is used as a classifier for the level of maturity pineapples. Artificial neural network input is a statistical parameter consisting of mean, standard deviation, variance, kurtosis, and skewness of RGB and HSV color models pineapple images. Statistical parameters of the color model with a Pearson correlation value greater than 0.5 were used to characterize pineapple images. A total of 360 pineapple images were used in the training process with a percentage of 75% of training data and 25% of validation data. An image segmentation process is applied to separate the pineapple image from the image background. The result of this research is a pineapple maturity level identification system consisting of software and hardware which is able to identify six indexes of pineapple maturity level with average accuracy value of 98,4%.

Pengaruh Variasi Kadar CaCO3 terhadap Pertumbuhan Fase Superkonduktor BPSCCO–2212 Menggunakan Metode Pencampuran Basah

This research was conducted to determine the effect of CaCO3 levels on the formation of superconducting phase BPSCCO - 2212 by calculating the level of purity of the phases formed and looking at the microstructure. The variation of CaCO3 was 0.95, 1.00, 1.05 and 1.10 mole using the wet mixing method. The samples were calcined at 800 ° C for 10 hours, and sintered at 820 ° C for 20 hours. Synthesized samples were characterized using X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The XRD’s chacterization results show that the level of purity of the formed phases increases with increasing Ca levels with maximum point at BPSCCO-2212/1.10 mole. The highest volume fraction was 79,06% in the BPSCCO-2212/1.10 sample. While the lowest volume fraction was 72.10% in the BPSCCO-2212/0.95 sample. Meanwhile, the highest degree of orientation was 20.59% at BPSCCO-2212/0.95. The lowest degree of orientation was 8.46% at BPSCCO-2212/1.10. SEM’s chacterization results show of all samples have been oriented altought not perfect yet and have relatively little space between slabs (voids).