scholarly journals Low temperature preparation of α-tricalcium phosphate and its mechanical properties

2017 ◽  
Vol 11 (2) ◽  
pp. 100-105 ◽  
Author(s):  
Song Wang ◽  
Yaping Wang ◽  
Kangning Sun ◽  
Xiaoning Sun
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Tricalcium Phosphate ◽  
Annealing Temperature ◽  
Thermal Transformation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Low Temperature Preparation ◽  
Scanning Electron ◽  
Temperature Preparation

In this work, ?-tricalcium phosphate (?-TCP) was successfully prepared by the thermal transformation of amorphous calcium phosphate (ACP) precursor. ?-cyclodextrin (?-CD) was used for preparation of ACP precursor and played an important role in designing its special structure. The phase composition and microstructures of the obtained ?-TCP at different annealing temperature were analysed by X-ray diffraction and scanning electron microscope, and confirmed that ?-TCP can be prepared at 650?C for 3 h using ACP as precursor, which is much lower than the phase transition temperature of ?-TCP. Mechanical properties were tested 24 h after mixing the obtained ?-TCP with 30 wt.% of deionised water. The compressive strength and the flexural strength were 26.4MPa and 12.0MPa, respectively. The flexural strength was higher than that of ?-TCP prepared by other methods.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-TiC-ZrO2 Ceramic Composites

2012 ◽  
Vol 476-478 ◽  
pp. 1031-1035
Author(s):  
Wei Min Liu ◽  
Xing Ai ◽  
Jun Zhao ◽  
Yong Hui Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Al2O3-TiC-ZrO2ceramic composites (ATZ) were fabricated by hot-pressed sintering. The phases and microstructure of the composites were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The relative density and mechanical properties (flexural strength, fracture toughness and Vicker’s hardness) of the composites were tested. The results show that the microstructure of the composites was the gray core-white rim. With the increase of sintering temperature, the relative density and mechanical properties of the composites increased first and then decreased. The composite sintered at 1705°C has the highest synthetical properties, and its relative density, flexural strength, fracture toughness and Vickers hardness are 98.3%,970MPa,6.0 MPa•m1/2and 20.5GPa, respectively.

STUDY OF MECHANICAL PROPERTIES AND FRACTURE MODE OF ALUMINA-SILICON CARBIDE NANOCOMPOSITES

2012 ◽  
Vol 05 ◽  
pp. 551-558 ◽  
Author(s):  
A. RAHIMNEZHAD YAZDI ◽  
H.R. BAHARVANDI ◽  
H. ABDIZADEH ◽  
N. EHSANI
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Silicon Carbide ◽  
Flexural Strength ◽  
Fracture Mode ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sic Particles ◽  
Scanning Electron

In this study Al 2 O 3- SiC nanocomposites have been fabricated by mixing of alumina and silicon carbide nano powders, followed by hot pressing at 1700°C. The mechanical properties and fracture mode of Al 2 O 3- SiC nanocomposites containing different volume fractions (5, 10 and 15%) of nano scale SiC particles were investigated and compared with those of alumina. Al 2 O 3- SiC powders were prepared by planetary milling in isopropanol. Fracture mode of specimens was investigated by means of scanning electron microscopy. Nanocomposites were tougher than alumina when they were hot pressed at the same temperature, and the values of nanocomposite's flexural strength and hardness were higher than those of alumina. Flexural strength, hardness and fracture toughness of the nanocomposites increase by increasing the volume percent of SiC up to 10% and then decrease slightly. The Scanning electron microscopy observations showed that fracture mode changes from intergranular for alumina to transgranular for nanocomposites. Finally X-ray diffraction analysis couldn't detect any chemical reactions between Al 2 O 3 and SiC particles.

TiCN-Based Cermets Strengthened with SiC Nano-Whiskers by Spark Plasma Sintering

2012 ◽  
Vol 512-515 ◽  
pp. 932-935
Author(s):  
Ying Peng ◽  
Zhi Jian Peng ◽  
Xiao Yong Ren ◽  
Hui Yong Rong ◽  
Cheng Biao Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Flexural Strength ◽  
Spark Plasma Sintering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Addition Amount ◽  
Scanning Electron

TiCN-based cermets with different amounts of SiC nano-whiskers were prepared by spark plasma sintering. The microstructure and mechanical properties of the as-prepared cermets were investigated. X-ray diffraction revealed that there were no SiC peaks detected, turning out some peaks of new carbide and silicate hard phases. Scanning electron microscopy indicated that there were more and more pores in the cermets with increasing amount of SiC whisker added, and the fracture mechanism of the cermets was mainly inter-granular fracture. With increasing addition amount of nano-SiC whisker, the hardness and flexural strength of the cermets increased first and decreased then, presenting the highest hardness (2170 HV) and flexural strength (750 MPa), respectively, when the addition content of nano-whiskers is 2.5 wt%.

Improving Mechanical Properties of Autoclaved Aerated Concrete by Sugar Sediment

2013 ◽  
Vol 807-809 ◽  
pp. 1266-1269 ◽  
Author(s):  
Atthakorn Thongtha ◽  
Somchai Maneewan ◽  
Chantana Punlek ◽  
Yothin Ungkoon
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Crystalline Morphology ◽  
X Ray Diffraction ◽  
Quality Class ◽  
X Ray ◽  
Autoclaved Aerated Concrete ◽  
Aerated Concrete ◽  
Scanning Electron

The comparison of microstructure and mechanical properties between the autoclaved aerated concrete (AAC) and the autoclaved aerated concrete consist of sugar sediment (AAC-SS) was investigated in this work. The microstructure of AAC and AAC-SS was analyzed by the scanning electron microscopy (SEM). The mechanical properties of AAC and AAC-SS were focused on the compressive strength, the density, the water absorption and the flexural strength. To comfirm the tobermorite phase, the phase formation of the samples was tested using X-ray diffraction (XRD). It was found that the microstructure of AAC and AAC-SS surface was the finer needle-like crystalline morphology. The compressive strength (5.9 N/mm2) and flexural strength (1.82 N/mm2) of AAC-SS were higher than that of the AAC (5.0 N/mm2 and 1.64 N/mm2). While, the value of density (0.60 g/cm3) and humidity (23.59%) of AAC-SS had little less than that of the AAC (0.61 g/cm3 and 24.11%). The increasing of the tobermorite phase, which was added by the sugar sediment, had affected to the improvement of the mechanical properties. The specimens of both AAC and AAC-SS were claimed in quality class of 4, which based on the Thai Industrial Standard 1505-1998.

scholarly journals Effect of Calcination Temperature on Mechanical Properties of Magnesium Oxychloride Cement

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 607
Author(s):  
Chenggong Chang ◽  
Lingyun An ◽  
Rui Lin ◽  
Jing Wen ◽  
Jinmei Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Calcination Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Magnesium Oxychloride ◽  
Magnesium Oxychloride Cement ◽  
Scanning Electron ◽  
Oxychloride Cement

In order to make full use of magnesium chloride resources, the development and utilisation of magnesium oxychloride cement have become an ecological and economic goal. Thus far, however, investigations into the effects on these cements of high temperatures are lacking. Herein, magnesium oxychloride cement was calcinated at various temperatures and the effects of calcination temperature on microstructure, phase composition, flexural strength, and compressive strength were studied by scanning electron microscopy, X-ray diffraction, and compression testing. The mechanical properties varied strongly with calcination temperature. Before calcination, magnesium oxychloride cement has a needle-like micromorphology and includes Mg(OH)2 gel and a trace amount of gel water as well as 5 Mg(OH)2·MgCl2·8H2O, which together provide its mechanical properties (flexural strength, 18.4 MPa; compressive strength, and 113.3 MPa). After calcination at 100 °C, the gel water is volatilised and the flexural strength is decreased by 57.07% but there is no significant change in the compressive strength. Calcination at 400 °C results in the magnesium oxychloride cement becoming fibrous and mainly consisting of Mg(OH)2 gel, which helps to maintain its high compressive strength (65.7 MPa). When the calcination temperature is 450 °C, the microstructure becomes powdery, the cement is mainly composed of MgO, and the flexural and compressive strengths are completely lost.

scholarly journals Ag+, Cu2+ and Zn2+ doped hydroxyapatite/tricalcium phosphate bioceramics: Influence of doping and sintering technique on mechanical properties

2018 ◽  
Vol 12 (3) ◽  
pp. 268-276 ◽  
Author(s):  
Zeljko Radovanovic ◽  
Ðordje Veljovic ◽  
Lidija Radovanovic ◽  
Ilmars Zalite ◽  
Eriks Palcevskis ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tricalcium Phosphate ◽  
Microwave Sintering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hydroxyapatite Ceramics ◽  
Average Grain Size ◽  
Conventional Sintering ◽  
Scanning Electron

Green hydroxyapatite ceramics were obtained by cold uniaxial and isostatic pressing of hydrothermally synthesized powders, pure hydroxyapatite and hydroxyapatite doped with Ag+, Cu2+ and Zn2+ ions. The ceramics were conventionally and microwave sintered and analyzed by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, X-ray diffraction analysis, and energy-dispersive X-ray spectroscopy. The effect of doping on the mechanical properties of the obtained hydroxyapatite/tricalcium phosphate ceramics was examined by comparing their average grain size, porosity and values of the hardness and fracture toughness. The results showed that doping with Cu2+ ions caused the lowest porosity of the ceramics and the highest values of hardness and fracture toughness. The ceramics obtained from hydroxyapatite doped with Ag+ and Zn2+ ions exhibited worse mechanical properties due to the higher porosity even in the case of microwave sintering, which provide denser ceramics than conventional sintering.

Effect of the Neodymium Content on Mechanical Properties of the Electro-Brush Plated Nano-Al2O3/Ni Composite Coating

2012 ◽  
Vol 525-526 ◽  
pp. 277-280
Author(s):  
Guo Jin ◽  
Xiu Fang Cui ◽  
Er Bao Liu ◽  
Qing Fen Li
Keyword(s):  
Mechanical Properties ◽  
Rare Earth ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Composite Coating ◽  
Nanoindentation Test ◽  
X Ray Diffraction ◽  
X Ray ◽  
Small Cracks ◽  
Scanning Electron

The effect of the neodymium content on mechanical properties of the electro-brush plated nanoAl2O3/Ni composite coating was investigated in this paper. The microstructure and phase structure were studied with scanning electron microscope (SEM) and X-ray diffraction (XRD). The hardness and abrasion properties of several coatings with different neodymium content were studied by nanoindentation test and friction / wear experiment. Results show that the coatings are much finer and more compact when the neodymium was added, and the hardness and abrasion property of the coatings with neodymium were improved obviously. Besides, the small cracks conduced by the upgrowth stress in the coatings were ameliorated when the rare earth neodymium was added. The improvement mechanism was further discussed.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

Synthesis of Alpha-Tricalcium Phosphate by Wet Reaction and Evaluation of Mechanical Properties

2012 ◽  
Vol 727-728 ◽  
pp. 1164-1169 ◽  
Author(s):  
Mônica Beatriz Thürmer ◽  
Rafaela Silveira Vieira ◽  
Juliana Machado Fernandes ◽  
Wilbur Trajano Guerin Coelho ◽  
Luis Alberto Santos
Keyword(s):  
Mechanical Properties ◽  
Calcium Phosphate ◽  
Tricalcium Phosphate ◽  
Calcium Nitrate ◽  
Chemical Precipitation ◽  
Particle Size Analysis ◽  
Size Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Calcium Phosphate Cements

Calcium phosphate cements have bioactivity and osteoconductivity and can be molded and replace portions of bone tissue. The aim of this work was to study the obtainment of α-tricalcium phosphate, the main phase of calcium phosphate cement, by wet reaction from calcium nitrate and phosphoric acid. There are no reports about α-tricalcium phosphate obtained by this method. Two routes of chemical precipitation were evaluated and the use of two calcinations temperatures to obtain the phase of cement. The influence of calcination temperature on the mechanical properties of cement was evaluated. Cement samples were characterized by particle size analysis, X-ray diffraction, mechanical strength and scanning electron microscopy. The results demonstrate the strong influence of synthesis route on the crystalline phases of cement and the influence of concentration of reactants on the product of the reaction, as well as, on the mechanical properties of cement.

Effect of Different Coiling Temperature on Mechanical Properties in Hot Rolled TRIP Steel

2011 ◽  
Vol 239-242 ◽  
pp. 1092-1095
Author(s):  
Xu Tao Gao ◽  
Ai Min Zhao ◽  
Zheng Zhi Zhao ◽  
Ming Ming Zhang ◽  
Di Tang
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
X Ray Diffraction ◽  
Coiling Temperature ◽  
Experimental Steel ◽  
Transformation Induced Plasticity ◽  
X Ray ◽  
Trip Steels ◽  
Hot Rolled ◽  
Scanning Electron

By means of optical microscopy(OM), scanning electron microscopy(SEM),X-ray diffraction(XRD),And tensile test, Mechanical Properties of hot rolled transformation -induced plasticity (TRIP) steels which were prepared through three different coiling temperature was investigated. Result reveals that the formability index of the experimental steel descends when the coiling temperature becomes low. Different coiling temperature has greater impact on retained austenite. Amount and carbon content of retained austenite in the experimental steel get less with lower coiling temperature.

Sign in / Sign up

Export Citation Format

Share Document