TiCN-Based Cermets Strengthened with SiC Nano-Whiskers by Spark Plasma Sintering

2012 ◽  
Vol 512-515 ◽  
pp. 932-935
Author(s):  
Ying Peng ◽  
Zhi Jian Peng ◽  
Xiao Yong Ren ◽  
Hui Yong Rong ◽  
Cheng Biao Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Flexural Strength ◽  
Spark Plasma Sintering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Addition Amount ◽  
Scanning Electron

TiCN-based cermets with different amounts of SiC nano-whiskers were prepared by spark plasma sintering. The microstructure and mechanical properties of the as-prepared cermets were investigated. X-ray diffraction revealed that there were no SiC peaks detected, turning out some peaks of new carbide and silicate hard phases. Scanning electron microscopy indicated that there were more and more pores in the cermets with increasing amount of SiC whisker added, and the fracture mechanism of the cermets was mainly inter-granular fracture. With increasing addition amount of nano-SiC whisker, the hardness and flexural strength of the cermets increased first and decreased then, presenting the highest hardness (2170 HV) and flexural strength (750 MPa), respectively, when the addition content of nano-whiskers is 2.5 wt%.

THE GROWTH OF MnSi1.73 PREPARED BY SPARK PLASMA SINTERING

2004 ◽  
Vol 18 (01) ◽  
pp. 87-93 ◽  
Author(s):  
ZHIMIN WANG ◽  
YIDONG WU ◽  
YUANJIN HE
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Spark Plasma Sintering ◽  
X Ray Diffraction ◽  
Mechanical Pressure ◽  
Growth Processes ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Scanning Electron

Crystals of MnSi 1.73 were prepared by Spark Plasma Sintering (SPS) technique, analyzed by X-ray diffraction (XRD), and invested by metalogragh and scanning electron microscopy (SEM). The growth processes of the samples were studied. It was found that the Mn–Si powders partly formed MnSi 1.73 crystals at 912–937 K under the mechanical pressure of 20 MPa in low vacuum (about 5.0 Pa), and fully formed MnSi 1.73 crystals after sintered at 1173 K for 15 minutes under 40 MPa.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-TiC-ZrO2 Ceramic Composites

2012 ◽  
Vol 476-478 ◽  
pp. 1031-1035
Author(s):  
Wei Min Liu ◽  
Xing Ai ◽  
Jun Zhao ◽  
Yong Hui Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Al2O3-TiC-ZrO2ceramic composites (ATZ) were fabricated by hot-pressed sintering. The phases and microstructure of the composites were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The relative density and mechanical properties (flexural strength, fracture toughness and Vicker’s hardness) of the composites were tested. The results show that the microstructure of the composites was the gray core-white rim. With the increase of sintering temperature, the relative density and mechanical properties of the composites increased first and then decreased. The composite sintered at 1705°C has the highest synthetical properties, and its relative density, flexural strength, fracture toughness and Vickers hardness are 98.3%,970MPa,6.0 MPa•m1/2and 20.5GPa, respectively.

Spark Plasma Sintering of Paper-Derived Ti3AlC2-Based Composites: Influence of Sintering Temperature

2021 ◽  
Vol 1016 ◽  
pp. 1790-1796
Author(s):  
Maxim Syrtanov ◽  
Egor Kashkarov ◽  
Tatyana Murashkina ◽  
Nahum Travitzky
Keyword(s):  
Phase Composition ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Total Content ◽  
X Ray Diffraction ◽  
X Ray ◽  
Carbide Phases ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Scanning Electron

This paper describes the influence of sintering temperature on phase composition and microstructure of paper-derived Ti3AlC2 composites fabricated by spark plasma sintering. The composites were sintered at 100 MPa pressure in the temperature range of 1150-1350 °C. Phase composition and microstructure were analyzed by X-ray diffraction and scanning electron microscopy, respectively. The multiphase structure was observed in the sintered composites consisting of Ti3AlC2, Ti2AlC, TiC and Al2O3 phases. The decomposition of the Ti3AlC2 phase into Ti2AlC and TiC carbide phases was observed with temperature rise. The total content of Ti3AlC2 and Ti2AlC phases was reduced from 84.5 vol.% (1150 °C) to 69.5 vol.% (1350 °C). The density of composites affected by both the content of TiC phase and changes in porosity.

Microstructures and Mechanical Properties of Ti-43Al-5V-4Nb-Y Alloy Consolidated by Spark Plasma Sintering

2016 ◽  
Vol 704 ◽  
pp. 183-189
Author(s):  
Yong Jun Su ◽  
Yi Feng Zheng ◽  
De Liang Zhang ◽  
Fan Tao Kong
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Tial Alloy ◽  
Tensile Tests ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Short Period ◽  
Spark Plasma ◽  
Fully Lamellar

TiAl alloy with a composition of Ti-43Al-5V-4Nb-Y (at.%) was prepared by spark plasma sintering (SPS). The TiAl powders were sintered between 650°C and 1300°C for 5 min under different loads. With the increasing of the temperature, the diffusion of the elements can be observed. Full compaction is achieved in a short period of time and the overall processing duration does not exceed 30 min. A fully lamellar structure was seen in the TiAl alloy after heat treatment. The microstructures of the samples were determined by X-ray diffraction and scanning electron microscopy. Their mechanical properties were evaluated by tensile tests performed at room temperature

Effect of the Dwell Temperature on Spark Plasma Sintered CaCu3Ti4O12

2012 ◽  
Vol 727-728 ◽  
pp. 982-987
Author(s):  
E. de Carvalho ◽  
Marcelo Bertolete ◽  
Izabel Fernanda Machado ◽  
E.N.S. Muccillo
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Lattice Parameter ◽  
Solid State Reactions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Diffraction Patterns ◽  
Scanning Electron

Polycrystalline CaCu3Ti4O12 ceramics were prepared by solid state reactions by spark plasma sintering (SPS) technique. In this study, the effects of the dwell temperature on structural, microstructural and dielectric properties of CaCu3Ti4O12 ceramics have been investigated. Powder mixtures were calcined at 900°C for 18 h before SPS consolidation. The dwell temperatures were 850, 900, 915 and 930°C. Sintered pellets were characterized by X-ray diffraction, scanning electron microscopy and impedance spectroscopy. X-ray diffraction patterns show evidences of a single-phase perovskite-type structure. The calculated lattice parameter is 7.40 Å. The hydrostatic density increases slightly with increasing dwell temperature. Scanning electron microscopy observations revealed a heterogeneous microstructure for all samples. The dielectric loss remains constant over a wide temperature range. The obtained permittivity is approximately 103 at 1 kHz. The increase of the dwell temperature is found to produce a brittle ceramic.

STUDY OF MECHANICAL PROPERTIES AND FRACTURE MODE OF ALUMINA-SILICON CARBIDE NANOCOMPOSITES

2012 ◽  
Vol 05 ◽  
pp. 551-558 ◽  
Author(s):  
A. RAHIMNEZHAD YAZDI ◽  
H.R. BAHARVANDI ◽  
H. ABDIZADEH ◽  
N. EHSANI
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Silicon Carbide ◽  
Flexural Strength ◽  
Fracture Mode ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sic Particles ◽  
Scanning Electron

In this study Al 2 O 3- SiC nanocomposites have been fabricated by mixing of alumina and silicon carbide nano powders, followed by hot pressing at 1700°C. The mechanical properties and fracture mode of Al 2 O 3- SiC nanocomposites containing different volume fractions (5, 10 and 15%) of nano scale SiC particles were investigated and compared with those of alumina. Al 2 O 3- SiC powders were prepared by planetary milling in isopropanol. Fracture mode of specimens was investigated by means of scanning electron microscopy. Nanocomposites were tougher than alumina when they were hot pressed at the same temperature, and the values of nanocomposite's flexural strength and hardness were higher than those of alumina. Flexural strength, hardness and fracture toughness of the nanocomposites increase by increasing the volume percent of SiC up to 10% and then decrease slightly. The Scanning electron microscopy observations showed that fracture mode changes from intergranular for alumina to transgranular for nanocomposites. Finally X-ray diffraction analysis couldn't detect any chemical reactions between Al 2 O 3 and SiC particles.

Fullerene-Metal Composites: Phase Transformations During Milling and Sintering

2011 ◽  
Vol 172-174 ◽  
pp. 727-732 ◽  
Author(s):  
Ileana Irais Santana ◽  
Francisco Carlos Robles Hernandez ◽  
Vicente Garibay-Febles ◽  
Hector A. Calderon
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Phase Transformations ◽  
Mechanical Milling ◽  
X Ray Diffraction ◽  
Metal Composites ◽  
X Ray ◽  
Plasma Sintering ◽  
Transmission Electron ◽  
Spark Plasma

Composites of Fe-C60and Al C60produced by mechanical milling and sinterized by Spark Plasma Sintering are investigated with special attention to the mechanical properties of the products. The processing involves phase transformations of the fullerenes that are interesting to follow and characterize. This involves formation of tetragonal/rhombohedral diamond and carbides during sintering and milling. Transmission Electron Microscopy (TEM) and Raman Spectroscopy techniques are also used to confirm preliminary results of X Ray Diffraction (XRD) related to the formation of nanostructures i.e., grain size of the crystals during mechanical milling and after sintering, spatial distribution of phases and the different phases that are developed during processing.

scholarly journals Behavior of Intermetallic Compounds of Al-Ti Composite Manufactured by Spark Plasma Sintering

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 331 ◽  
Author(s):  
Kwangjae Park ◽  
Dasom Kim ◽  
Kyungju Kim ◽  
Seungchan Cho ◽  
Hansang Kwon
Keyword(s):  
Intermetallic Compounds ◽  
Spark Plasma Sintering ◽  
Electron Probe ◽  
High Hardness ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Formation Behavior ◽  
Spark Plasma ◽  
Scanning Electron

In this research, we successfully fabricate high-hardness and lightweight Al-Ti composites. Al-Ti composites powders with three compositions (Al-20, 50, and 80 vol.% Ti) are mixed using ball milling and subsequently subjected to spark plasma sintering (SPS). The microstructures and phases of the Al-Ti composites are characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD) spectroscopy, and field emission-electron probe microanalysis (FE-EPMA). These tests confirm the presence of several intermetallic compounds (ICs) (Al3Ti, Al5Ti2, Al11Ti5) in the composites, and we are able to confirm that these ICs are produced by the reaction of Al and Ti during the SPS process. Furthermore, thermogravimetric-differential thermal analysis (TG-DTA) is used to analyze the formation behavior of the ICs. In addition, the mechanical properties of the composites are measured using their Vickers hardness and it is observed that the Al-80 vol.% Ti composite exhibits the highest hardness. Consequently, it is assumed that SPS is suitable for fabricating Al-Ti composites which represent the next-generation materials to be used in various industrial fields as high-hardness and lightweight materials.

scholarly journals Properties of WCCo Composites Produced by the SPS Method Intended for Cutting Tools for Machining of Wood-Based Materials

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2618
Author(s):  
Joanna Wachowicz ◽  
Tomasz Dembiczak ◽  
Grzegorz Stradomski ◽  
Zbigniew Bałaga ◽  
Marcin Dyner ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Primary Particle ◽  
Cutting Tools ◽  
Cobalt Content ◽  
Primary Particle Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Scanning Electron

This paper presents the possibility of using the Spark Plasma Sintering (SPS) method to obtain WCCo composite materials. Such materials are used as cutting blades for machining wood-based materials. Two series of composites, different in grain size and cobalt content, were analyzed in the paper. The produced materials were characterized using Scanning Electron Microscopy (SEM), X-ray diffraction (XRD), and tribological properties were determined. In addition, preliminary tests were carried out on the durability of the blades made of sintered WCCo composites while machining three-layer chipboard. The results of the microstructure analysis proved that the SPS method makes it possible to obtain solid composites. Phase analysis showed the occurrence of the following phases: WC, Co, and Co3W9C4. The lowest friction coefficient value was found in samples sintered using powder with an average primary particle size of 400 nm (ultrafine).

Phase Composition and Microstructure of Binderless WC-ZrC Cemented Carbides Fabricated by Spark Plasma Sintering

2014 ◽  
Vol 602-603 ◽  
pp. 556-560
Author(s):  
Xiao Yong Ren ◽  
Zhi Jian Peng ◽  
Hui Yong Rong ◽  
Ying Peng ◽  
Cheng Biao Wang ◽  
...  
Keyword(s):  
Phase Composition ◽  
Spark Plasma Sintering ◽  
Uniaxial Pressure ◽  
Cemented Carbides ◽  
X Ray Diffraction ◽  
X Ray ◽  
Abnormal Growth ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Scanning Electron

Binderless WC-based cemented carbides with different fractions (0-9 wt.%) of ZrC nanopowder were fabricated through spark plasma sintering at 1600 °C under a uniaxial pressure of 50 MPa. The addition effect of ZrC nanopowder on the phase composition and microstructure of the fabricated materials were explored with the help of X-ray diffraction and scanning electron microscope. The results indicated that W2C phase was detected in the samples with 0-3 wt.% ZrC nanopowder, but with further increase in ZrC added fraction, ZrO2 phase instead of W2C phase was detected. The apparent density decreased gradually with the increase in added fraction of ZrC nanopowder, while the relative density increased initially and then decreased, reaching its maximum of about 98.2% when the added fraction of ZrC nanopowder was about 3 wt.%, indicating that appropriate added fraction of ZrC nanopowder can improve the densification of binderless WC cemented carbides. Without ZrC nanopowder, the coarsening and abnormal growth of WC grains were serious, resulting in many large prismatic WC grains in the samples. However, Such phenomena could be suppressed by adding ZrC nanopowder, resulting in much finer and more homogenous microstructure after 1-3 wt.% ZrC nanopowder was added. When the added fraction of ZrC nanopowder was higher than 3 wt.%, the agglomeration of ZrC nanopowder became more and more serious.

Sign in / Sign up

Export Citation Format

Share Document