scholarly journals Modelling the effect of injection pressure on heat release parameters and nitrogen oxides in direct injection diesel engines

2014 ◽  
Vol 18 (1) ◽  
pp. 155-168 ◽  
Author(s):  
Levent Yüksek ◽  
Tarkan Sandalci ◽  
Orkun Özener ◽  
Alp Ergenc
Keyword(s):  
Nitrogen Oxides ◽  
Heat Release ◽  
Direct Injection ◽  
Pressure Rise ◽  
Injection Pressure ◽  
Premixed Combustion ◽  
Crank Angle ◽  
Cylinder Model ◽  
Combustion Phase ◽  
Rate Of Heat Release

Investigation and modelling the effect of injection pressure on heat release parameters and engine-out nitrogen oxides are the main aim of this study. A zero-dimensional and multi-zone cylinder model was developed for estimation of the effect of injection pressure rise on performance parameters of diesel engine. Double-Wiebe rate of heat release global model was used to describe fuel combustion. extended Zeldovich mechanism and partial equilibrium approach were used for modelling the formation of nitrogen oxides. Single cylinder, high pressure direct injection, electronically controlled, research engine bench was used for model calibration. 1000 and 1200 bars of fuel injection pressure were investigated while injection advance, injected fuel quantity and engine speed kept constant. The ignition delay of injected fuel reduced 0.4 crank angle with 1200 bars of injection pressure and similar effect observed in premixed combustion phase duration which reduced 0.2 crank angle. Rate of heat release of premixed combustion phase increased 1.75 % with 1200 bar injection pressure. Multi-zone cylinder model showed good agreement with experimental in-cylinder pressure data. Also it was seen that the NOx formation model greatly predicted the engine-out NOx emissions for both of the operation modes.

Study of cycle-by-cycle variations of natural gas direct injection combustion using a rapid compression machine

2003 ◽  
Vol 217 (1) ◽  
pp. 53-61 ◽  
Author(s):  
Z Huang ◽  
S Shiga ◽  
T Ueda ◽  
H Nakamura ◽  
T Ishima ◽  
...  
Keyword(s):  
Natural Gas ◽  
Heat Release ◽  
Maximum Rate ◽  
Direct Injection ◽  
Pressure Rise ◽  
Maximum Pressure ◽  
Rapid Compression Machine ◽  
Combustion Duration ◽  
Rate Of Heat Release ◽  
Rapid Compression

Cycle-by-cycle variations of natural gas direct injection (CNG DI) combustion were studied by using a rapid compression machine. Results show that CNG DI combustion can realize high combustion stability with less cycle-by-cycle variation in the maximum pressure rise, the maximum rate of pressure rise and the maximum rate of heat release at the given equivalence ratios. Mixture stratification and fast flame propagation with the aid of turbulence produced by the high speed fuel jet are considered to be responsible for these behaviours. Cycle-by-cycle variations in combustion durations and combustion products present higher magnitudes than those of maximum pressure rise and maximum rate of heat release. Cycle-by-cycle variations of CO and unburned CH4 show an interdependence with the variation of the late combustion duration, and the variation of NO x shows an interdependence with the variation of the rapid combustion duration. Cycle-by-cycle variations are found to be insensitive to the equivalence ratios in CNG DI combustion.

Injection Timing Variation and its Influence on the Performance and Combustion Characteristics on a Direct Injection CI Engine

2018 ◽  
Vol 10 (1) ◽  
Author(s):  
V. Hariram ◽  
S. Seralathan ◽  
M. Rajasekaran ◽  
G. John
Keyword(s):  
Direct Injection ◽  
Pressure Rise ◽  
Engine Performance ◽  
Injection Pressure ◽  
Injection Timing ◽  
Gas Temperature ◽  
Optimum Parameters ◽  
Rate Of Heat Release ◽  
Ci Engine ◽  
And Performance

The present experimental investigation aims at improving the combustion and performance parameters by varying the injection timing. A 3.5 kW single cylinder stationary CI engine equipped with eddy current dynamometer is used in this investigation. The static injection timing is varied using spill method by an advancement and retirement of 2 CAD with respect to standard injection timing of 23 BTDC. On comparison with the standard injection timing, the brake thermal efficiency, cylinder pressure, rate of heat release, mean gas temperature and rate of pressure rise are found to increase along with a significant decrease in brake specific fuel consumption for an advanced injection timing of 21 BTDC. Negative improvement is observed with respect to retarded injection timing of 25 BTDC. Optimum parameters for enhanced engine performance is found to be 21 BTDC injection timing with a 200 bar injection pressure at rated speed.

Multi-point micro-flame ignited hybrid lean-burn combustion of gasoline with direct injection dimethyl ether

2019 ◽  
Vol 22 (1) ◽  
pp. 140-151 ◽  
Author(s):  
Xue-Qing Fu ◽  
Bang-Quan He ◽  
Si-Peng Xu ◽  
Tao Chen ◽  
Hua Zhao ◽  
...  
Keyword(s):  
Nitrogen Oxides ◽  
Heat Release ◽  
Dimethyl Ether ◽  
Direct Injection ◽  
Injection Timing ◽  
Ignition Timing ◽  
Double Peak ◽  
Lean Burn ◽  
Combustion Duration ◽  
Low Nitrogen

Lean-burn combustion is effective in reducing fuel consumption of gasoline engines because of the higher specific heat ratio of the fuel lean mixture and reduced heat loss from lower combustion temperature. However, its application to real engines is hampered by the unstable ignition, high cyclic variability, and partial-burn due to slower combustion, as well as the restricted maximum lean-burn air/fuel ratio limit and the insufficiently low nitrogen oxides emission. Multi-point micro-flame-ignited hybrid combustion has been proposed and applied to extend the lean burn limit of premixed gasoline and air mixture. To achieve micro-flame-ignited combustion in premixed lean gasoline mixture formed by port fuel injection, a small amount of dimethyl ether is injected directly into the cylinder of a four-stroke gasoline engine to control and accelerate the ignition and combustion process so that the engine could be operated with the overall excess air coefficient (Lambda) of 1.9. The results show that heat release processes can be grouped into three forms, that is, ramp type, double-peak type, and trapezoid type. Regardless of single or split injections, direct injection timing of dimethyl ether dominates the features of heat release. The ramp type occurs at early injection timing while the double-peak type takes place at late injection timing. Trapezoid type appears between the above two types. Dimethyl ether injection timing controls the ignition timing and has less effect on combustion duration. Single injection of dimethyl ether leads to much earlier ignition timing and slightly longer combustion duration, forming higher nitrogen oxides emissions than the split injections. Ultra-low nitrogen oxides emissions and higher thermal efficiency are achieved in the ramp type combustion compared to the other two types of combustion in both injection approaches.

Evaluation of Fuel Injection Strategies for Biodiesel-Fueled CRDI Engine Development and Particulate Studies

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Akhilendra Pratap Singh ◽  
Avinash Kumar Agarwal
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Pressure Rise ◽  
Injection Pressure ◽  
Combustion Noise ◽  
Emission Characteristics ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Injection Parameters ◽  
Smoke Opacity

Fuel injection parameters such as fuel injection pressure (FIP) and start of main injection (SoMI) timings significantly affect the performance and emission characteristics of a common rail direct injection (CRDI) diesel engine. In this study, a state-of-the-art single cylinder research engine was used to investigate the effects of fuel injection parameters on combustion, performance, emission characteristics, and particulates and their morphology. The experiments were carried out at three FIPs (400, 700, and 1000 bar) and four SoMI timings (4 deg, 6 deg, 8 deg, and 10 deg bTDC) for biodiesel blends [B20 (20% v/v biodiesel and 80% v/v diesel) and B40 (40% v/v biodiesel and 60% v/v diesel)] compared to baseline mineral diesel. The experiments were performed at a constant engine speed (1500 rpm), without pilot injection and exhaust gas recirculation (EGR). The experimental results showed that FIP and SoMI timings affected the in-cylinder pressure and the heat release rate (HRR), significantly. At higher FIPs, the biodiesel blends resulted in slightly higher rate of pressure rise (RoPR) and combustion noise compared to baseline mineral diesel. All the test fuels showed relatively shorter combustion duration at higher FIPs and advanced SoMI timings. The biodiesel blends showed slightly higher NOx and smoke opacity compared to baseline mineral diesel. Lower particulate number concentration at higher FIPs was observed for all the test fuels. However, biodiesel blends showed emission of relatively higher number of particulates compared to baseline mineral diesel. Significantly lower trace metals in the particulates emitted from biodiesel blend fueled engine was an important finding of this study. The particulate morphology showed relatively smaller number of primary particles in particulate clusters from biodiesel exhaust, which resulted in relatively lower toxicity, rendering biodiesel to be more environmentally benign.

Study on the Combustion Characteristics of the Engine Fueled with DME-Diesel Blends

2014 ◽  
Vol 953-954 ◽  
pp. 1381-1385
Author(s):  
Wei Li ◽  
Yun Peng Li ◽  
Fan Bin Li
Keyword(s):  
Heat Release ◽  
Pressure Rise ◽  
Mechanical Efficiency ◽  
Diesel Oil ◽  
Cylinder Pressure ◽  
Mass Ratio ◽  
Combustion Duration ◽  
Crank Angle ◽  
Maximum Combustion Temperature ◽  
Stroke Engine

To further study the performance of the engine fueled with DME-diesel blends, the indicator diagrams of a two-cylinder four-stroke engine are recorded at 1700r/min and 2300r/min under different load, the heat release rate and the rate of pressure rise are calculated. The results show that: when fueled the engine with D20 blend (Mass ratio of DME and diesel oil is 2:10) and optimizing the fuel supply advance angle, the maximum cylinder pressure decreases by 10% averagely and its corresponding crank angle delays 2°CA, the maximum rate of pressure rise is relatively lowers about 20%, the beginning of heat release delays，but combustion duration do not extend, and the centroid of heat release curves is closer to TDC (Top Dead Center), maximum combustion temperature drops 70-90K. These results indicate that the mechanical efficiency will be improved and, NOx emissions and mechanical noise will be reduced when an engine fueled with DME-diesel blends.

Combustion Characteristics of Methane Direct Injection Engine Under Various Injection Timings and Injection Pressures

2017 ◽  
Vol 139 (8) ◽  
Author(s):  
Jingeun Song ◽  
Mingi Choi ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Direct Injection Engine ◽  
Optical Engine ◽  
Start Of Injection ◽  
Crank Angle ◽  
Combustion Speed ◽  
Injection Pressures

The performance of a methane direct injection engine was investigated under various fuel injection timings and injection pressures. A single-cylinder optical engine was used to acquire in-cylinder pressure data and flame images. An outward-opening injector was installed at the center of the cylinder head. Experimental results showed that the combustion characteristics were strongly influenced by the end of injection (EOI) timing rather than the start of injection (SOI) timing. Late injection enhanced the combustion speed because the short duration between the end of injection and the spark-induced strong turbulence. The flame propagation speeds under various injection timings were directly compared using crank-angle-resolved sequential flame images. The injection pressure was not an important factor in the combustion; the three injection pressure cases of 0.5, 0.8, and 1.1 MPa yielded similar combustion trends. In the cases of late injection, the injection timings of which were near the intake valve closing (IVC) timing, the volumetric efficiency was higher (by 4%) than in the earlier injection cases. This result implies that the methane direct injection engine can achieve higher torque by means of the late injection strategy.

Experimental investigation of the combustion characteristics of a biodiesel (rice-bran oil methyl ester)-fuelled direct-injection transportation diesel engine

2007 ◽  
Vol 221 (8) ◽  
pp. 921-932 ◽  
Author(s):  
S Sinha ◽  
A K Agarwal
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Vegetable Oils ◽  
Rice Bran ◽  
Rice Bran Oil ◽  
Direct Injection ◽  
Pressure Rise ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Crank Angle

Increased environmental awareness and depletion of fossil petroleum resources are driving industry to develop alternative fuels that are environmentally more acceptable. Transesterified vegetable oil derivatives called ‘biodiesel’ appear to be the most convenient way of utilizing bio-origin vegetable oils as substitute fuels in diesel engines. The methyl esters of vegetable oils do not require significant modification of existing engine hardware. Previous research has shown that biodiesel has comparable performance and lower brake specific fuel consumption than diesel with significant reduction in emissions of CO, hydrocarbons (HC), and smoke but slightly increased NO x emissions. In the present experimental research work, methyl ester of rice-bran oil is derived through transesterification of rice-bran oil using methanol in the presence of sodium hydroxide (NaOH) catalyst. Experimental investigations have been carried out to examine the combustion characteristics in a direct injection transportation diesel engine running with diesel, biodiesel (rice-bran oil methyl ester), and its blends with diesel. Engine tests were performed at different engine loads ranging from no load to rated (100 per cent) load at two different engine speeds (1400 and 1800 r/min). A careful analysis of the cylinder pressure rise, heat release, and other combustion parameters such as the cylinder peak combustion pressure, rate of pressure rise, crank angle at which peak pressure occurs, rate of pressure rise, and mass burning rates was carried out. All test fuels exhibited similar combustion stages as diesel; however, biodiesel blends showed an earlier start of combustion and lower heat release during premixed combustion phase at all engine load-speed combinations. The maximum cylinder pressure reduces as the fraction of biodiesel increases in the blend and, at higher engine loads, the crank angle position of the peak cylinder pressure for biodiesel blends shifted away from the top dead centre in comparison with baseline diesel data. The maximum rate of pressure rise was found to be higher for diesel at higher engine loads; however, combustion duration was higher for biodiesel blends.

Determination of the Start and End of Combustion in a Direct Injection Diesel Engine Using the Apparent Heat Release Rate

2017 ◽  
Author(s):  
Joseph Gerard T. Reyes ◽  
Edwin N. Quiros
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Direct Injection ◽  
Injection Timing ◽  
Fuel Injector ◽  
Direct Injection Diesel Engine ◽  
Crank Angle ◽  
Start Of Combustion

The combustion duration in an internal combustion engine is the period bounded by the engine crank angles known as the start of combustion (SOC) and end of combustion (EOC), respectively. This period is essential in analysis of combustion for the such as the production of exhaust emissions. For compression-ignition engines, such as diesel engines, several approaches were developed in order to approximate the crank angle for the start of combustion. These approaches utilized the curves of measured in-cylinder pressures and determining by inspection the crank angle where the slope is steep following a minimum value, indicating that combustion has begun. These pressure data may also be utilized together with the corresponding cylinder volumes to generate the apparent heat release rate (AHRR), which shows the trend of heat transfer of the gases enclosed in the engine cylinder. The start of combustion is then determined at the point where the value of the AHRR is minimum and followed by a rapid increase in value, whereas the EOC is at the crank angle where the AHRR attains a flat slope prior to the exhaust stroke of the engine. To verify the location of the SOC, injection line pressures and fuel injection timing are also used. This method was applied in an engine test bench using a four-cylinder common-rail direct injection diesel engine with a pressure transducer installed in the first cylinder. Injector line pressures and fuel injector voltage signals per engine cycle were also recorded and plotted. By analyzing the trends of this curves in line with the generated AHRR curves, the SOC may be readily determined.

Cylinder Pressure Information-Based Postinjection Timing Control for Aftertreatment System Regeneration in a Diesel Engine—Part I: Derivation of Control Parameter

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Hyunjun Lee ◽  
Manbae Han ◽  
Myoungho Sunwoo
Keyword(s):  
Phase Shift ◽  
Heat Release ◽  
Exhaust Emissions ◽  
Cylinder Pressure ◽  
Combustion Analysis ◽  
Operating Condition ◽  
Combustion Phase ◽  
Rate Of Heat Release ◽  
Engine Operating Condition ◽  
Aftertreatment Systems

The implementation of aftertreatment systems in passenger car diesel engines, such as a lean NOx trap (LNT) and a diesel particulate filter (DPF), requires an in-cylinder postinjection (POI) for a periodic regeneration of those aftertreatment systems to consistently reduce tail-pipe emissions. Although the combustion and emission characteristics are changed from the normal engine operating conditions due to the POI, POI is generally applied with a look-up table (LUT) based feedforward control because of its cost effectiveness and easy implementation into the engine management system (EMS). However, the LUT-based POI control necessities tremendous calibration work to find the optimal timing to supply high exhaust gas temperature or enough reductants such as carbon monoxide (CO) and hydrocarbon to regenerate the aftertreatment systems while maintaining low engine-out smoke emissions. To solve this problem, we propose a novel combustion analysis method based on the cylinder pressure information. This method investigates the relation between the POI timing with the exhaust emissions and compensates the combustion phase shift occurred by the engine operating condition changes, such as the engine speed and injection quantity. A burning rate of fuel after a location of the rate of heat release maximum (BRaLoROHRmax) was derived from the combustion analysis. A mass fraction burned X% after a location of the rate of heat release maximum (MFBXaLoROHRmax) was determined using the BRaLoROHRmax and main injection (MI) quantity. Nonlinear characteristics of the exhaust emissions according to POI timing variations and the combustion phase shift due to the engine operating condition changes can be easily analyzed and compensated in terms of the proposed MFBXaLoROHRmax domain. The proposed method successfully evaluated its utility through the engine experiments for the LNT and DPF regeneration.

Influence of piston bowl geometry on combustion and emission characteristics

2019 ◽  
Vol 233 (5) ◽  
pp. 576-587 ◽  
Author(s):  
Ramazan Şener ◽  
Mehmed R Özdemir ◽  
Murat U Yangaz
Keyword(s):  
Heat Release ◽  
Renewable Energy Sources ◽  
Combustion Characteristics ◽  
Emission Rates ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Piston Bowl ◽  
Crank Angle ◽  
Rate Of Heat Release ◽  
Exhaust Valves

Together with the global energy concerns, the norms are getting stringent to prevent the emission threat. There are on-going studies on systems working with both fossil and renewable energy sources aiming to create more efficient and less emissive processes and devices. Accordingly, a set of numerical simulations was performed to examine the effect of the bowl shape of a piston on the performance behaviour, emission rates and combustion characteristics in a four-cylinder, four strokes, water-cooled compression ignition engine using n-heptane (C7H16) as fuel. Six different piston bowl geometries, five from the literature and proposed one, were utilized having different length-to-diameter ratio, curvature and sidewall radius. The study was conducted at 1750 r/min engine speed and a constant compression ratio with a full performance condition. The intake and exhaust valves have been considered as closed during the analysis to provide the variation of crank angle from 300 CA to 495 CA. The results showed that the piston bowl geometry has a significant impact on the rate of heat release, in-cylinder pressure, in-cylinder temperature, and emission trends in the engine. Among the piston bowl geometries studied, design DE and design DF exhibited better combustion characteristics and relatively lower emission trends compared to other designs. The observed rate of heat release, in-cylinder pressure and in-cylinder temperature magnitudes of these two geometries was higher in comparison to other geometries. Moreover, the trade-off for NOx emission was also observed higher for these piston bowl designs.

Sign in / Sign up

Export Citation Format

Share Document