scholarly journals Preparation of Activated Carbons based Balanites Aegyptiaca Shells by Chemical Activation: Optimization Conditions Using the Methodology of Experimental Design

2020 ◽  
Vol 1 (6) ◽  
Author(s):  
Rene B. N. Lekene ◽  
Naphtali O. Ankoro ◽  
Ndi J. Nsami ◽  
Daouda Kouotou ◽  
Abdoul N. Rahman ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Experimental Design ◽  
Residence Time ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Carbon Yield ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
Methylene Blue Number

The optimization conditions of preparation of activated carbons based Balanites aegytiaca shells by chemical activation was investigated. The effects of three parameters of preparation namely, the activation temperature (600-800 °C), impregnation ratio (1:4-3:8) and residence time (60-120 min) were thoroughly studied on the activated carbon yield (Yld, Y1), iodine number (ION,Y2) and methylene blue number (MBN, Y3) using the Methodology of Experimental Design (MED). The analysis of variance (ANOVA) under the experimental domain revealed that, the activation temperature of 800 °C, residence time of 02hrs and impregnation ratio of 1:2 were the optimum conditions of preparation leading to activated carbon yield of 23.0%, iodine number of 889.0 mg/g and methylene blue number of 9.7 mg/g. The polynomial equation showed that the three parameters were both synergetic and antagonistic on the responses retained. The higher values of iodine numbers obtained alongside the experimental matrix is an indication that the activated carbons so prepared were mainly microporous.

scholarly journals Optimization of Conditions for the Preparation of Activated Carbon from Lapsi (Choerospondias axillaris) Seed Stone Using ZnCl2

2016 ◽  
Vol 11 (1) ◽  
pp. 128-139 ◽  
Author(s):  
Rinita Rajbhandari Joshi
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Iodine Number ◽  
Surface Area ◽  
Zinc Chloride ◽  
Pore Volume ◽  
Chemical Activation ◽  
Carbonization Temperature ◽  
Carbon Yield ◽  
Methylene Blue Number

Activated carbon was prepared from Lapsi (Choerospondias axillaries ) seed stone by chemical activation method using ZnCl2. The effect of experimental variables; ZnCl2 ratio, temperature and carbonization time on the quality of the activated carbon were systematically invested by determining the carbon yield, iodine number, methylene blue number, surface area and pore volume. Lapsi seed stone powder (LSP) of particle size < 300 μm was used to prepare activated carbon under N2 atmosphere. An increase in ZnCl2 ratio in general increased the iodine number and methylene blue number, but on increasing zinc chloride above 50 percentages, iodine and methylene blue number increased only marginally. An increase in carbonization temperature increases the iodine number, methylene blue number, and surface area and pore volume. Increase in carbonization time from 3 hour to 4 hour increases iodine number and methylene blue number and thereafter the increase in iodine number and methylene blue number is gradual. Regarding the carbon yield, it decreases with the ZnCl2 ratio above 50 percent, and the yield also decreases with increase in temperature and carbonization time. Therefore the optimum conditions for the preparation of activated carbon from Lapsi seed stone using ZnCl2 as follows: carbonization temperature of 400°C, zinc chloride ratio as LSP:ZnCl2 equals 1:1, and carbonization time of 4 hour. This resulted an activated carbon with 791 iodine number, 364 methylene blue number, 1167 surface area and 0.65 pore volume.Journal of the Institute of Engineering, 2015, 11(1): 128-139

Analisis Variasi Temperatur Aktivasi Terhadap Daya Serap Arang Aktif Tandan Aren (Arenga Pinnata Merr) Dengan Agen Aktivasi Potassium Silicate(K2SiO3)

2020 ◽  
Vol 5 (3) ◽  
pp. 221
Author(s):  
Muhammad Azam ◽  
Muhammad Anas ◽  
Erniwati Erniwati
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Temperature Variation ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Potassium Silicate ◽  
Physical Activation ◽  
Activation Temperature ◽  
Pyrolysis Reactor

This study aims to determine the effect of variation of activation temperature of activated carbon from sugar palm bunches of chemically activatied with the activation agent of potassium silicate (K2SiO3) on the adsorption capacity of iodine and methylene blue. Activated carbon from bunches of sugar palmacquired in four steps: preparationsteps, carbonizationstepsusing the pyrolysis reactor with temperature of 300 oC - 400 oC for 8 hours and chemical activation using of potassium silicate (K2SiO3) activator in weight ratio of 2: 1 and physical activation using the electric furnace for 30 minutes with temperature variation of600 oC, 650 oC, 700 oC, 750 oC and 800 oC. The iodine and methyleneblue adsorption testedby Titrimetric method and Spectrophotometry methodrespectively. The results of the adsorption of iodine and methylene blue activated carbon from sugar palm bunches increased from 240.55 mg/g and 63.14 mg/g at a temperature of 600 oC to achieve the highest adsorption capacity of 325.80 mg/g and 73.59 mg/g at temperature of 700 oC and decreased by 257.54 mg/g and 52.03 mg/g at a temperature of 800 oCrespectively.However, it does not meet to Indonesia standard (Standard Nasional Indonesia/SNI), which is 750 mg/g and 120 mg/g respectively.

scholarly journals Computer Analysis of the Effect of Activation Temperature on the Microporous Structure Development of Activated Carbon Derived from Common Polypody

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2951
Author(s):  
Mirosław Kwiatkowski ◽  
Jarosław Serafin ◽  
Andy M. Booth ◽  
Beata Michalkiewicz
Keyword(s):  
Activated Carbon ◽  
Porous Structure ◽  
Computer Analysis ◽  
Density Functional ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Geometrical Parameters ◽  
Activation Process ◽  
Microporous Structure ◽  
Activation Temperature

This paper presents the results of a computer analysis of the effect of activation process temperature on the development of the microporous structure of activated carbon derived from the leaves of common polypody (Polypodium vulgare) via chemical activation with phosphoric acid (H3PO4) at activation temperatures of 700, 800, and 900 °C. An unconventional approach to porous structure analysis, using the new numerical clustering-based adsorption analysis (LBET) method together with the implemented unique gas state equation, was used in this study. The LBET method is based on unique mathematical models that take into account, in addition to surface heterogeneity, the possibility of molecule clusters branching and the geometric and energy limitations of adsorbate cluster formation. It enabled us to determine a set of parameters comprehensively and reliably describing the porous structure of carbon material on the basis of the determined adsorption isotherm. Porous structure analyses using the LBET method were based on nitrogen (N2), carbon dioxide (CO2), and methane (CH4) adsorption isotherms determined for individual activated carbon. The analyses carried out showed the highest CO2 adsorption capacity for activated carbon obtained was at an activation temperature of 900 °C, a value only slightly higher than that obtained for activated carbon prepared at 700 °C, but the values of geometrical parameters determined for these activated carbons showed significant differences. The results of the analyses obtained with the LBET method were also compared with the results of iodine number analysis and the results obtained with the Brunauer–Emmett–Teller (BET), Dubinin–Radushkevich (DR), and quenched solid density functional theory (QSDFT) methods, demonstrating their complementarity.

scholarly journals Optimisation of durian peel based activated carbon preparation conditions for dye removal

2013 ◽  
Vol 16 (1) ◽  
pp. 22-31
Author(s):  
Phung Thi Kim Le ◽  
Kien Anh Le
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Dye Removal ◽  
Activated Carbons ◽  
Low Cost ◽  
Waste Water Treatment ◽  
Impregnation Ratio ◽  
Carbon Production ◽  
Removal Capacity

Agricultural wastes are considered to be a very important feedstock for activated carbon production as they are renewable sources and low cost materials. This study present the optimize conditions for preparation of durian peel activated carbon (DPAC) for removal of methylene blue (MB) from synthetic effluents. The effects of carbonization temperature (from 673K to 923K) and impregnation ratio (from 0.2 to 1.0) with potassium hydroxide KOH on the yield, surface area and the dye adsorbed capacity of the activated carbons were investigated. The dye removal capacity was evaluated with methylene blue. In comparison with the commercial grade carbons, the activated carbons from durian peel showed considerably higher surface area especially in the suitable temperate and impregnation ratio of activated carbon production. Methylene blue removal capacity appeared to be comparable to commercial products; it shows the potential of durian peel as a biomass source to produce adsorbents for waste water treatment and other application. Optimize condition for preparation of DPAC determined by using response surface methodology was at temperature 760 K and IR 1.0 which resulted the yield (51%), surface area (786 m2/g), and MB removal (172 mg/g).

scholarly journals Optimization of Activated Carbons Prepared byH3PO4and Steam Activation of Oil Palm Shells

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Daouda Kouotou ◽  
Horace Ngomo Manga ◽  
Abdelaziz Baçaoui ◽  
Abdelrani Yaacoubi ◽  
Joseph Ketcha Mbadcam
Keyword(s):  
Activated Carbon ◽  
Oil Palm ◽  
Activated Carbons ◽  
Optimum Conditions ◽  
Steam Activation ◽  
Experimental Conditions ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
Preparation Conditions ◽  
Two Factors

In this study, activated carbons were prepared from oil palm shells by physicochemical activation. The methodology of experimental design was used to optimize the preparation conditions. The influences of the impregnation ratio (0.6–3.4) and the activation temperature between 601°C and 799°C on the following three responses: activated carbon yield (R/AC-H3PO4), the iodine adsorption (I2/AC-H3PO4), and the methylene blue adsorption (MB/AC-H3PO4) results were investigated using analysis of variance (ANOVA) to identify the significant parameters. Under the experimental conditions investigated, the activation temperature of 770°C and impregnation ratio of 2/1 leading to the R/AC-H3PO4of 52.10%, theI2/AC-H3PO4of 697.86 mg/g, and the MB/AC-H3PO4of 346.25 mg/g were found to be optimum conditions for producing activated carbon with well compromise of desirability. The two factors had both synergetic and antagonistic effects on the three responses studied. The micrographs of activated carbons examined with scanning electron microscopy revealed that the activated carbons were found to be mainly microporous and mesoporous.

Activated carbon powder derived from cashmere guard hair

2019 ◽  
Vol 50 (5) ◽  
pp. 599-615
Author(s):  
Zhuanyong Zou ◽  
Xin Liu ◽  
Jiahui Ding ◽  
Tanqi Chen ◽  
Xungai Wang
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Carbon Powder ◽  
Guard Hair ◽  
Carbon Yield ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
Study Results

Converting waste fiber to high value-added carbonaceous materials has been considered as an effective and affordable route in response to the increasing volume of waste fiber in recent year. In this study, we are the first to prepare activated carbon powder derived from cashmere guard hair as a renewable waste protein fiber, using a chemical activation method at different impregnation ratios of K2CO3/cashmere guard hair char and activation temperatures ranging from 400℃ to 600℃. Characterization of the activated carbon powder was carried out by morphology study, specific surface area study, and adsorption study. Results have shown that the increase of the impregnation ratio and the activation temperature created more microporous structure in the activated carbon powder, and then increased the specific surface area of the activated carbon powder as well as the amount of methylene blue adsorbed. However, the carbon yield increases with the increase in the impregnation ratio of K2CO3/cashmere guard hair char and decreases with the increase in the activation temperature. The activated carbon powder, activated by the condition of 1:2 K2CO3/cashmere guard hair char impregnation ratio and 600℃ activation temperature, has a specific surface area of 764.86 m2g−1 and a carbon yield of 14.07 wt%. Compared to the activated carbon powder derived from fine merino wool fibers, the activated carbon powder derived from cashmere guard hair has higher carbon yield, surface area, and total pore volume, showing a superior adsorption performance.

Preparation of activated carbons from wet activated sludge by direct chemical activation

2009 ◽  
Vol 59 (12) ◽  
pp. 2387-2394 ◽  
Author(s):  
X. Wang ◽  
N. Zhu ◽  
J. Xu ◽  
B. Yin
Keyword(s):  
Activated Carbon ◽  
Activated Sludge ◽  
Water Content ◽  
Iodine Value ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Total Pore Volume ◽  
Processing Parameters ◽  
Experimental Conditions ◽  
Activation Temperature

An improved method for preparing activated carbons from wet waste activated sludge (WAS) by direct chemical activation was studied in this paper. The effects of processing parameters on iodine adsorption capacity of the product were investigated. Results show that sludge-based activated carbon prepared with KOH had a larger iodine value than those activated with ZnCl2 and KCl. The maximum iodine value was observed at the KOH concentration of 0.50 M. Increasing the impregnation time from 10 to 20 h resulted in a 20% increase in the iodine value. The highest iodine value was obtained at the activation temperature of 600°C and holding time of 1 h. Sludge water content had insignificant effects on the iodine value of products. Raw WAS with a water content of 93.2% can be converted into an activated carbon with a high specific surface area of 737.6 m2 g−1 and iodine value of 864.8 mgg−1 under optimum experimental conditions. Other physical properties such as total pore volume, micropore volume and mean pore diameter of the product were also reported and compared with those of commercial activated carbon.

Preparation and Characterization of Activated Carbon from Reedy Grass Leaves by Chemical Activation with KOH

2014 ◽  
Vol 881-883 ◽  
pp. 579-583 ◽  
Author(s):  
Ling Zhi Chen ◽  
Dong Xu Miao ◽  
Xiao Jie Feng ◽  
Jian Zhong Xu
Keyword(s):  
Iodine Number ◽  
Surface Area ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Raw Material ◽  
Bet Surface Area ◽  
Activation Temperature ◽  
Impregnation Ratio ◽  
Dta Analysis

Activated carbons (AC) were produced by chemical activation with potassium hydroxide (KOH) at 800°C from chars that were carbonized from reedy grass leaves at 450°C in N2atmosphere. The effects of the weight ratio of KOH/char ( impregnation ratio), activation temperature and duration time were examined. Adsorption capacity was demonstrated with iodine number. BET surface area, pore volume and pore size of activated carbons were characterized by N2adsorption isotherms. The maximum surface area and iodine number of the AC was 1100 m2/g and 1080 mg/g produced at 800°C for2h and impregnation ratio is 4:1.The characteristics of activated carbons were determined by Infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). Thermal gravimetry (TG/DTA) analysis of raw material was carried out.

scholarly journals Process Optimization of High Surface Area Activated Carbon Prepared from Cucumis Melo by H3PO4 Activation for the Removal of Cationic and Anionic Dyes Using Full Factorial Design

2021 ◽  
Vol 11 (5) ◽  
pp. 12662-12679
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Cucumis Melo ◽  
Contact Time ◽  
Chemical Activation ◽  
Activation Time ◽  
Anionic Dyes ◽  
Activation Temperature ◽  
Full Factorial

In this study, Chemical activation was used to prepare a low-cost activated carbon (AC) from agricultural waste material: Cucumis melo. It was used as a green biosorbent for the removal of cationic and anionic dyes from aqueous solutions (Methylene blue (MB) and Acid orange 7 (AO7)).A full factorial 24 experimental design was used to optimize the preparation conditions. The factors and levels included are activation temperature (300 and 500ºC), activation time (1 and 3 h), H3PO4 concentration (1.5 and 2.5 mol/L), and contact time (60 and 90 min). The surface area of the activated carbons and high removal efficiency of MB and AO7 was chosen as a measure of the optimization. The activated carbon prepared at 500 °C, for 3 hours with an H3PO4 concentration of 2.5 mol/L and a contact time of 90 min, have the largest specific surface area (475 m2/g) and the percentage of discoloration of methylene blue (99.4%). Furthermore, the greater value of AO7 removal (94.20%) was obtained at 3h - activation time, 500°C - activation temperature, 1.5 mol/L - H3PO4 concentration with a 90 min contact time.

scholarly journals Preparation of Activated Carbon from (Punica granatum .sp) Wood by Chemical Treatment Using Potassium Hydroxide.

2019 ◽  
Vol 24 (6) ◽  
pp. 45
Author(s):  
Mayada M . Ali1 ◽  
Firas E. Fatthee2 ◽  
Ahmed AbdulkarimThunoon3
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Iodine Number ◽  
Chemical Treatment ◽  
Potassium Hydroxide ◽  
Activated Carbons ◽  
Punica Granatum ◽  
Ash Content ◽  
Activating Agent ◽  
Methylene Blue Number

In the present study, activated carbons were prepared from Punicagranatum .sp, using potassium hydroxide as activating agent. Punicagranatum .sp activated carbon(PGAC) was characterization using methylene blue number, iodine number and some physical properties such as humidity, ash content and density. The perfect measurement for this study was the proportion of (1:2.5)(wood : KOH) to give 560mg for iodine number and 67mg for methylene blue number which are good result.   http://dx.doi.org/10.25130/tjps.24.2019.107

Sign in / Sign up

Export Citation Format

Share Document