scholarly journals Welding Thermal Cycles of Joints Made of S1100QL Steel by Saw and Hybrid Plasma-Mag Processes

2020 ◽  
Vol 20 (4) ◽  
pp. 75-86
Author(s):  
A. Sajek
Keyword(s):  
Quality Assessment ◽  
Welded Joints ◽  
Heat Input ◽  
Thermal Effects ◽  
Arc Welding ◽  
Measurement Data ◽  
Welding Process ◽  
Thermal Conditions ◽  
Hybrid Plasma ◽  
Welding Processes

AbstractThe aim of this article is to validate the method of conducting a multipoint temperature measurement in the area of welded joints as a tool for quality assessment of the joints in question. In order to establish a relationship between temperature readout at a given point, the value of heat input and the distance of the point form the weld axis, preliminary tests have been conducted on a set of padding welds. Correlation of measurement data analysis showed the high 0.99 level. In the second stage of the study, temperatures of joints welded with two different methods have been measured: the HPAW (Hybrid Plasma – Arc Welding) and classic SAW (Submerged Arc Welding) method. The obtained temperature curves reflect the intensity of heat input in a given welding process. When compared to thermal effects on metallographic specimens, the shapes of the curves show a potential for quality assessment of joints in production conditions. Estimating thermal effects with classic analytical methods proves imprecise with respect to advanced high-power welding processes. Monitoring temperature will allow to assess the quality of joints in the course of welding, which may be a remarkable factor in terms of limiting the HAZ (heat affected zone) tempering of joints made from MART steels (advanced high strength martensitic steel) – a phenomenon that exceedingly decreases the strength of the joints. The method for quality assessment of welded joints presented in this paper allows to extend the analysis of welding thermal conditions.

Effect of Different Arc Welding Processes on the Metallurgical and Mechanical Properties of Ramor 500 Armor Steel

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Ali Günen ◽  
Selçuk Bayar ◽  
Mustafa Serdar Karakaş
Keyword(s):  
Mechanical Properties ◽  
Welded Joints ◽  
Arc Welding ◽  
Impact Resistance ◽  
Welding Process ◽  
Fusion Welding ◽  
Minor Amount ◽  
Cold Metal Transfer ◽  
Armor Steel ◽  
Welding Processes

Abstract In the present study, Ramor 500 armor steel plates were automatically welded using cold metal transfer arc welding (CMT), gas metal arc welding (GMAW), and hybrid plasma arc welding (HPAW) methods. To investigate the effects of three different fusion welding methods on metallurgical and mechanical properties, the welded joints were examined using optical microscopy, scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS) and also subjected to radiographic, hardness, tensile, and notched impact tests. The weld metal (WM) region of the GMAW and HPAW joints consisted of massive austenite. In the CMT welded joint, the WM consisted mainly of dendritic austenite and a minor amount of δ-ferrite. Regardless of the welding process, the hardness of both the WM and heat-affected zone (HAZ) regions was found to be higher than the base metal (BM). The tensile strengths obtained by CMT, GMAW, and HPAW were 45%, 50%, and 65% of the BM, respectively. Cleavage-type brittle fractures occurred in the GMAW and HPAW welded joints, while localized ductile fractures occurred in the CMT joints. Tensile test specimens of the CMT joints fractured in the WM, while the GMAW and HPAW joints fractured in the HAZ. In terms of notch toughness, the CMT joints exhibited better impact resistance compared with the BM. GMAW and HPAW joints displayed less impact resistance than the BM, with values comparable with previous studies in the literature.

Advanced submerged arc welding processes for Arctic structures and ice-going vessels

2016 ◽  
Vol 232 (1) ◽  
pp. 114-127
Author(s):  
Pavel Layus ◽  
Paul Kah ◽  
Viktor Gezha
Keyword(s):  
Case Studies ◽  
Arc Welding ◽  
Oil And Gas ◽  
Welding Process ◽  
Submerged Arc Welding ◽  
The Arctic ◽  
Correct Selection ◽  
Advantages And Disadvantages ◽  
Welding Processes ◽  
Submerged Arc

The Arctic region is expected to play an extremely prominent role in the future of the oil and gas industry as growing demand for natural resources leads to greater exploitation of a region that holds about 25% of the world’s oil and gas reserves. It has become clear that ensuring the necessary reliability of Arctic industrial structures is highly dependent on the welding processes used and the materials employed. The main challenge for welding in Arctic conditions is prevention of the formation of brittle fractures in the weld and base material. One mitigating solution to obtain sufficiently low-transition temperatures of the weld is use of a suitable welding process with properly selected parameters. This work provides a comprehensive review with experimental study of modified submerged arc welding processes used for Arctic applications, such as narrow gap welding, multi-wire welding, and welding with metal powder additions. Case studies covered in this article describe welding of Arctic steels such as X70 12.7-mm plate by multi-wire welding technique. Advanced submerged arc welding processes are compared in terms of deposition rate and welding process operational parameters, and the advantages and disadvantages of each process with respect to low-temperature environment applications are listed. This article contributes to the field by presenting a comprehensive state-of-the-art review and case studies of the most common submerged arc welding high deposition modifications. Each modification is reviewed in detail, facilitating understanding and assisting in correct selection of appropriate welding processes and process parameters.

Influence of Thermal Simulated and Real Tandem Submerged Arc Welding Process on the Microstructure and Mechanical Properties of the Coarse Grained Heat Affected Zone

2011 ◽  
Vol 110-116 ◽  
pp. 3191-3198
Author(s):  
Sadegh Moeinifar
Keyword(s):  
Grain Boundaries ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Arc Welding ◽  
Welding Process ◽  
Submerged Arc Welding ◽  
Rolled Plate ◽  
Arc Welding Process ◽  
Submerged Arc ◽  
Tandem Submerged Arc Welding

The high-strength low-alloy microalloyed steel was procured as a hot rolled plate with accelerated cooling. The Gleeble thermal simulated process involved heating the steel specimens to the peak temperature of 1400 °C, with constant cooling rates of 3.75 °C/s and 2 °C/s to room temperature. The four-wire tandem submerged arc welding process, with different heat input, was used to generate a welded microstructure. The martensite/austenite constituent appeared in the microstructure of the heat affected zone region for all the specimens along the prior-austenite grain boundaries and between bainitic ferrite laths. The blocky-like and stringer martensite/austenite morphology were observed in the heat affected zone regions. The martensite/austenite constituents were obtained by a combination of field emission scanning electron microscopes and image analysis software The Charpy absorbed energy of specimens was assessed using Charpy impact testing at-50 °C. Brittle particles, such as martensite/austenite constituent along the grain boundaries, can make an easy path for crack propagation. Similar crack initiation sites and growth mechanism were investigated for specimens welded with different heat input values.

Determination of Heat Input in Tungsten Inert Gas and Laser Welding of Type Optim 960 QC Structural Steel Using Adams’ Equation for 2-D Heat Distribution

2017 ◽  
Vol 750 ◽  
pp. 45-52
Author(s):  
Sveto Cvetkovski
Keyword(s):  
Laser Welding ◽  
Heat Input ◽  
Arc Welding ◽  
Research Work ◽  
Laser Beam Welding ◽  
Peak Temperature ◽  
Efficiency Coefficient ◽  
Zone Recrystallization ◽  
Welding Processes

The heat input during conventional arc welding processes can be readily calculated knowing the power taken from the power source. The efficiency coefficient can be taken from the appropriate literature standards. Here, the intention of the performed research work was to develop a procedure for determination of heat input in arc and laser welding processes implementing Adams equation - modified Rykalin equation for two dimensional heat distributions (2-D). To realize this idea, it is necessary to determine two characteristic temperatures points in the HAZ with known peak temperature, and to determine distance between them. Implementing measured values for distance in Adams’ equation, heat input in arc welding can be directly determined in arc welded joints.In laser beam welding, the absorption of the beam in the metal is not known, so that the welding heat input cannot be calculated directly, and direct implementation of Adam’s equation is not possible i.e. absorption coefficient has to be determined first, and after that calculation of heat input is possible.The peak temperatures corresponding to specific microstructures can be obtained by performing welding simulation, by the Gleeble 1500 simulator in our case. As one of the peak temperatures, the melting temperature can be used corresponding to the fusion line, so that at least one characteristic peak temperature such as coarse grain zone, fine grin zone, intercritical zone, recrystallization, has to be determined by the simulation.Performed research showed that obtained values for heat input using Adam’s equation correspond pretty well with standard equation for heat input in arc welding.

Microstructural Effects between AHSS Dissimilar Joints Using MIG and TIG Welding Process

2015 ◽  
Vol 1766 ◽  
pp. 29-35 ◽  
Author(s):  
G.Y. Pérez Medina ◽  
M. Padovani ◽  
M. Merlin ◽  
A.F. Miranda Pérez ◽  
F.A. Reyes Valdés
Keyword(s):  
Arc Welding ◽  
Gas Metal Arc Welding ◽  
Welding Process ◽  
High Hardness ◽  
Inert Gas ◽  
Mechanical Degradation ◽  
Low Alloy Steels ◽  
Dissimilar Joints ◽  
Lap Shear ◽  
Welding Processes

ABSTRACTGas tungsten arc welding-tungsten inert gas (GTAW-TIG) is focused in literature as an alternative choice for joining high strength low alloy steels; this study is performed to compare the differences between gas metal arc welding-metal inert gas (GMAW-MIG) and GTAW welding processes. The aim of this study is to characterize microstructure of dissimilar transformation induced plasticity steels (TRIP) and martensitic welded joints by GMAW and GTAW welding processes. It was found that GMAW process lead to relatively high hardness in the HAZ of TRIP steel, indicating that the resultant microstructure was martensite. In the fusion zone (FZ), a mixture of phases consisting of bainite, ferrite and small areas of martensite were present. Similar phase’s mixtures were found in FZ of GTAW process. The presence of these mixtures of phases did not result in mechanical degradation when the GTAW samples were tested in lap shear tensile testing as the fracture occurred in the heat affected zone. In order to achieve light weight these result are benefits which is applied an autogenous process, where it was shown that without additional weight the out coming welding resulted in a high quality bead with homogeneous mechanical properties and a ductile morphology on the fracture surface. Scanning electron microscopy (SEM) was employed to obtain information about the specimens that provided evidence of ductile morphology.

Features of structure formation processes in AA2024 alloy joints formed by the friction stir welding with bobbin tool

2021 ◽  
Vol 23 (2) ◽  
pp. 98-115
Author(s):  
Alexey Ivanov ◽  
◽  
Valery Rubtsov ◽  
Andrey Chumaevskii ◽  
Kseniya Osipovich ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Structure Formation ◽  
Welded Joints ◽  
Heat Input ◽  
Welded Joint ◽  
Welding Process ◽  
Tool Material ◽  
Travel Speed ◽  
Material System ◽  
Friction Stir

Introduction. One of friction stir welding types is the bobbin friction stir welding (BFSW) process, which allows to obtain welded joints in various configurations without using a substrate and axial embedding force, as well as to reduce heat loss and temperature gradient across the welded material thickness. This makes the BFSW process effective for welding aluminum alloys, which properties are determined by their structural-phase state. According to research data, the temperature and strain rate of the welded material have some value intervals in which strong defect-free joints are formed. At the same time, much less attention has been paid to the mechanisms of structure formation in the BFSW process. Therefore, to solve the problem of obtaining defect-free and strong welded joints by BFSW, an extended understanding of the basic mechanisms of structure formation in the welding process is required. The aim of this work is to research the mechanisms of structure formation in welded joint of AA2024 alloy obtained by bobbin tool friction stir welding with variation of the welding speed. Results and discussion. Weld formation conditions during BFSW process are determined by heat input into a welded material, its fragmentation and plastic flow around the welding tool, which depend on the ratio of tool rotation speed and tool travel speed. Mechanisms of joint formation are based on a combination of equally important processes of adhesive interaction in “tool-material” system and extrusion of metal into the region behind the welding tool. Combined with heat dissipation conditions and the configuration of the “tool-material” system, this leads to material extrusion from a welded joint and its decompaction. This results in formation of extended defects. Increasing in tool travel speed reduce the specific heat input, but in case of extended joints welding an amount of heat released in joint increases because of specific heat removal conditions. As a result, the conditions of adhesion interaction and extrusion processes change, which leads either to the growth of existing defects or to the formation of new ones. Taking into account the complexity of mechanisms of structure formation in joint obtained by BFSW, an obtaining of defect-free joints implies a necessary usage of various nondestructive testing methods in combination with an adaptive control of technological parameters directly in course of a welding process.

Effect of the Heat Input in the Transformation of Retained Austenite in Advanced Steels of Transformation Induced Plasticity (TRIP) Welded with Gas Metal Arc Welding

2013 ◽  
Vol 339 ◽  
pp. 700-705 ◽  
Author(s):  
Victor Lopez ◽  
Arturo Reyes ◽  
Patricia Zambrano
Keyword(s):  
Heat Input ◽  
Arc Welding ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Gas Metal Arc Welding ◽  
Welding Process ◽  
Residual Austenite ◽  
Welding Parameters ◽  
Transformation Induced Plasticity ◽  
Metal Arc Welding

The effect of heat input on the transformation of retained austenite steels transformation induced plasticity (TRIP) was investigated in the heat affected zone (HAZ) of the Gas Metal Arc Welding GMAW process. The determination of retained austenite of the HAZ is important in optimizing the welding parameters when welding TRIP steels, because this will greatly influence the mechanical properties of the welding joint due to the transformation of residual austenite into martensite due to work hardening. Coupons were welded with high and low heat input for investigating the austenite transformation of the base metal due to heat applied by the welding process and was evaluated by optical microscopy and the method of X-Ray Diffraction (XRD). Data analyzed shows that the volume fraction of retained austenite in the HAZ increases with the heat input applied by the welding process, being greater as the heat input increase and decrease the cooling rate, this due to variation in the travel speed of the weld path.

scholarly journals Contributions Regarding the Use of Mechanical Vibrations in Order to Improve the Properties of Steels and Welded Joints Used in Metal Constructions

2020 ◽  
Vol 21 (2) ◽  
pp. 67-71
Author(s):  
Gheorghe Novac ◽  
Bogdan Novac
Keyword(s):  
Welded Joints ◽  
Arc Welding ◽  
Significant Contribution ◽  
Welding Process ◽  
Internal Stresses ◽  
Welding Equipment ◽  
Welding Technology ◽  
Submerged Arc ◽  
Very High

The paper presents aspects regarding the influence of vibrations on the mechanical properties of welded joints, made with basic materials of Spanish and Romanian origin. In this research is presented the practical way to make the necessary assemblies for the proposed tests. The tests show that vibrations have a significant contribution to the quality of welded joints. This is explained by the appearance of several crystallization centres which makes the structure finer. By using vibrations, the atoms are rearranged in the structure, ensuring a proper de-tensioning. The stresses induced in welded metals are significantly reduced by the use of vibration during welding process. The addition materials have a significant contribution to the emergence of stresses in welded joints as well. These stresses can contribute to the appearance of microstructural constituents with significant hardness. The welding equipment and technologies used also have a significant contribution to the emergence of the remaining stresses. For example, the submerged arc welding technology (SAF) can introduce very high internal stresses. By using vibrations during the welding process, it is achieved a fine structure and a significant reduction of remaining stresses in the welded joints.

Sign in / Sign up

Export Citation Format

Share Document