scholarly journals Sound Absorption Properties of Materials Based on Recycled Plastic Granule Mixtures

2021 ◽  
Vol 29 (1) ◽  
pp. 15-19
Author(s):  
Andrea Biskupičová ◽  
Miriam Ledererová ◽  
Stanislav Unčík ◽  
Christ Glorieux ◽  
Monika Rychtáriková
Keyword(s):  
Absorption Spectrum ◽  
Absorption Coefficient ◽  
Sound Absorption ◽  
Ethylene Vinyl Acetate ◽  
Frequency Range ◽  
Absorption Properties ◽  
Audible Frequency ◽  
Properties Of Materials ◽  
Two Peaks ◽  
Foam Plastics

Abstract This article reports on impedance tube measurements of the sound absorption coefficient α (-) of selected recycled foam plastics, i.e., ethylene-vinyl acetate (EVA), polyvinyl chloride (PVC), polystyrene (PS), and polypropylene (PP), in different mixtures with a binding adhesive. The effect of the thickness of the sample on the sound absorption spectrum as well as the variability in absorption across the different samples of the same composition and thickness are discussed. For the EVA/ PP and PS/PP mixtures, the spectrum is characterized by two peaks that shift as the thickness is changing. These mixtures were also found to be the most absorbent across the whole audible frequency range.

scholarly journals Acoustic Panels Made of Paper Sludge and Clay Composites

2021 ◽  
Vol 13 (2) ◽  
pp. 637
Author(s):  
Tomas Astrauskas ◽  
Tomas Januševičius ◽  
Raimondas Grubliauskas
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Composite Panel ◽  
Sound Absorption Coefficient ◽  
Core Material ◽  
Paper Sludge ◽  
Frequency Range ◽  
Absorption Properties ◽  
Air Gaps ◽  
The Core

Studies on recycled materials emerged during recent years. This paper investigates samples’ sound absorption properties for panels fabricated of a mixture of paper sludge (PS) and clay mixture. PS was the core material. The sound absorption was measured. We also consider the influence of an air gap between panels and rigid backing. Different air gaps (50, 100, 150, 200 mm) simulate existing acoustic panel systems. Finally, the PS and clay composite panel sound absorption coefficients are compared to those for a typical commercial absorptive ceiling panel. The average sound absorption coefficient of PS-clay composite panels (αavg. in the frequency range from 250 to 1600 Hz) was up to 0.55. The resulting average sound absorption coefficient of panels made of recycled (but unfinished) materials is even somewhat higher than for the finished commercial (finished) acoustic panel (αavg. = 0.51).

Method of Testing of Sound Absorption Properties of Materials Intended for Ultrasonic Noise Protection

2013 ◽  
Vol 38 (2) ◽  
pp. 191-195 ◽  
Author(s):  
Dariusz Pleban
Keyword(s):  
Sound Absorption ◽  
Free Field ◽  
Tone Burst ◽  
Mineral Wool ◽  
Frequency Range ◽  
Absorption Properties ◽  
Open Cell Foam ◽  
Properties Of Materials ◽  
Cell Foam

Abstract Efficient ultrasonic noise reduction by using enclosures requires the knowledge of absorbing properties of materials in the frequency range above 4 kHz. However, standardized methods enable determination of absorption coefficients of materials in the frequency range up to 4 kHz. For this reason, it is proposed to carry out measurements of the sound absorption properties of materials in the free field by means of a tone-burst technique in the frequency range from 4 kHz to 40 kHz at angles of incidence varying from 0° to 60°. The absorption coefficient of a material is calculated from the reflection coefficient obtained by reflecting a tone-burst from both a perfectly reflecting panel and a combination of this panel and the sample of the tested material. The tests results show that mineral wool and polyurethane open-cell foam possess very good absorbing properties in this frequency range.

scholarly journals Non-Wovens as Sound Reducers

2018 ◽  
Vol 55 (2) ◽  
pp. 64-76
Author(s):  
D. Belakova ◽  
A. Seile ◽  
S. Kukle ◽  
T. Plamus
Keyword(s):  
Absorption Coefficient ◽  
Surface Density ◽  
Sound Absorption ◽  
Transmission Loss ◽  
Sound Transmission ◽  
Sound Insulation ◽  
Material Structure ◽  
Sound Transmission Loss ◽  
Sound Waves ◽  
Frequency Range

Abstract Within the present study, the effect of hemp (40 wt%) and polyactide (60 wt%), non-woven surface density, thickness and number of fibre web layers on the sound absorption coefficient and the sound transmission loss in the frequency range from 50 to 5000 Hz is analysed. The sound insulation properties of the experimental samples have been determined, compared to the ones in practical use, and the possible use of material has been defined. Non-woven materials are ideally suited for use in acoustic insulation products because the arrangement of fibres produces a porous material structure, which leads to a greater interaction between sound waves and fibre structure. Of all the tested samples (A, B and D), the non-woven variant B exceeded the surface density of sample A by 1.22 times and 1.15 times that of sample D. By placing non-wovens one above the other in 2 layers, it is possible to increase the absorption coefficient of the material, which depending on the frequency corresponds to C, D, and E sound absorption classes. Sample A demonstrates the best sound absorption of all the three samples in the frequency range from 250 to 2000 Hz. In the test frequency range from 50 to 5000 Hz, the sound transmission loss varies from 0.76 (Sample D at 63 Hz) to 3.90 (Sample B at 5000 Hz).

Utilization of Styrofoam ss Soundproofing Material with Auditory Frequency Range

2018 ◽  
Vol 13 (2) ◽  
Author(s):  
Sjahrul Meizar Nasri ◽  
Iting Shofwati
Keyword(s):  
Hearing Loss ◽  
Absorption Coefficient ◽  
Sound Absorption ◽  
Noise Exposure ◽  
Preventive Action ◽  
Frequency Range ◽  
Acoustical Property ◽  
Noise Barrier ◽  
Polystyrene Waste ◽  
Action Methods

One of preventive action methods of hearing loss that number tend to increase is by using brick that made from Styrofoam which is expected to have the ability as a soundproof that can be used to control the noise. The aim of this research is to assess the use of sound absorption material in which utilizing Styrofoam to reduce the noise exposure. In this study, cement and find aggregate that contain the Styrofoam and sand are mixed with the composition 1:4 and 1:6 and also by adding the polystyrene waste as much as 0%, 20%, 40%, 60%, and 80%.  To determine the acoustical property of the mixture, the sound absorbing coefficient (α) was determined by using Four Microphones Impedance Tube (ISO 140-3). The results showed that the highest absorption coefficient value was at frequency 800 Hz by adding 80% Styrofoam for the composition of 1:4 at 0.4100 dB and at the frequency 800 Hz by adding 40% Styrofoam for the composition 1:6 at 0.5870 dB. Based on the results of this research, further study to potentially use Styrofoam as noise barrier is suggested.

Broadening of the Sound Absorption Bandwidth of the Perforated Panel Using a Membrane-Type Resonator

2018 ◽  
Vol 140 (3) ◽  
Author(s):  
Xuezhi Zhu ◽  
Zhaobo Chen ◽  
Yinghou Jiao ◽  
Yanpeng Wang
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Degrees Of Freedom ◽  
Low Frequency ◽  
Absorption Capacity ◽  
Sound Absorption Coefficient ◽  
Sound Waves ◽  
Frequency Range ◽  
Absorption Bandwidth ◽  
Membrane Type

In order to broaden the sound absorption bandwidth of a perforated panel in the low frequency range, a lightweight membrane-type resonator is installed in the back cavity of the perforated panel to combine into a compound sound absorber (CSA). Because of the great flexibility, the membrane-type resonator can be vibrated easily by the incident sound waves passing through the holes of the perforated panel. In the low frequency range, the membrane-type resonator and the perforated panel constitute a two degrees-of-freedom (DOF)-resonant type sound absorption system, which generates two sound absorption peaks. By tuning the parameters of the membrane type resonator, a wide frequency band having a large sound absorption coefficient can be obtained. In this paper, the sound absorption coefficient of CSA is derived analytically by combining the vibration equation of the membrane-type resonator with the acoustic impedance equation of the perforated panel. The influences of the parameters of the membrane-type resonator on the sound absorption performance of the CSA are numerically analyzed. Finally, the wide band sound absorption capacity of the CSA is validated by the experimental test.

scholarly journals Elucidating the Sound Absorption Characteristics of Foxtail Millet (Setariaitalica) Husk

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5126
Author(s):  
Dhayalini Balasubramanian ◽  
Senthil Rajendran ◽  
Bhuvanesh Srinivasan ◽  
Nirmalakumari Angamuthu
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Foxtail Millet ◽  
Air Gap ◽  
Composite Panel ◽  
Sound Absorption Coefficient ◽  
Mass Content ◽  
Frequency Range ◽  
Backing Material ◽  
Absorption Characteristics

The current study deals with the analysis of sound absorption characteristics of foxtail millet husk powder. Noise is one the most persistent pollutants which has to be dealt seriously. Foxtail millet is a small seeded cereal cultivated across the world and its husk is less explored for its utilization in polymer composites. The husk is the outer protective covering of the seed, rich in silica and lingo-cellulose content making it suitable for sound insulation. The acoustic characterization is done for treated foxtail millet husk powder and polypropylene composite panels. The physical parameters like fiber mass content, density, and thickness of the composite panel were varied and their influence over sound absorption was mapped. The influence of porosity, airflow resistance, and tortuosity was also studied. The experimental result shows that 30-mm thick foxtail millet husk powder composite panel with 40% fiber mass content, 320 kg/m3 density showed promising sound absorption for sound frequency range above 1000 Hz. We achieved noise reduction coefficient (NRC) value of 0.54. In view to improve the performance of the panel in low-frequency range, we studied the efficiency of incorporating air gap and rigid backing material to the designed panel. We used foxtail millet husk powder panel of density 850 kg/m3 as rigid backing material with varying air gap thickness. Thus the composite of 320 kg/m3 density, 30-mm thick when provided with 35-mm air gap and backing material improved the composite’s performance in sound frequency range 250 Hz to 1000 Hz. The overall sound absorption performance was improved and the NRC value and average sound absorption coefficient (SAC) were increased to 0.7 and 0.63 respectively comparable with the commercial acoustic panels made out of the synthetic fibers. We have calculated the sound absorption coefficient values using Delany and Bezlay model (D&B model) and Johnson–Champoux–Allard model (JCA model) and compared them with the measured sound absorption values.

scholarly journals Sound Absorption Properties of Aluminum Sponges Manufactured by Infiltration Process

2010 ◽  
Vol 146-147 ◽  
pp. 1651-1654 ◽  
Author(s):  
Patricia M. Fernández ◽  
Luis J.R. Cruz ◽  
Luis E. García Cambronero ◽  
Cesar Díaz ◽  
María Ángeles Navacerrada
Keyword(s):  
Pore Size ◽  
Sound Absorption ◽  
Frequency Range ◽  
Absorption Factor ◽  
Absorption Properties ◽  
Infiltration Process ◽  
Interconnected Porosity ◽  
Factor Α

In this paper, the sound absorption properties of aluminum sponges manufactured by infiltration process have been studied. The results show that the sound absorption factor α changes in function of pore size. Additionally, the sound absorption factor α was sensitive to the frequency range measured and it was depending of the thickness sample. It was found that the interconnected porosity plays an important role increasing the sound absorption properties of the aluminum sponges studied.

Physical and Sound Absorption Properties of Spent Tea Leaf Fiber Filled Polyurethane Foam Composite

2014 ◽  
Vol 660 ◽  
pp. 541-546 ◽  
Author(s):  
Qumrul Ahsan ◽  
Chia Pooi Ching ◽  
Mohd Yuhazri bin Yaakob
Keyword(s):  
Absorption Coefficient ◽  
Polyurethane Foam ◽  
High Resistance ◽  
Sound Absorption ◽  
Filler Loading ◽  
Tea Plant ◽  
Sound Absorption Coefficient ◽  
Tea Leaves ◽  
Absorption Properties ◽  
Spent Tea Leaves

Spent tea leaves (STL) from tea producing factories can be considered as new resources for sound absorbing polyurethane (PU) matrix composite materials because STL are rich in polyphenols (tannins) which cause high durability, high resistance to fungal and termites, and high resistance to fire. The research aims to study the physical characteristics of STL and the effect of dispersion morphology of STL on the sound absorption properties of polyurethane foam composites by varying filler loading. Three grades of STL fibers either as received or granulated are used in this study, namely BM-FAE and SWBHE derived from the stalk while FIBER-FAE derived from the leaves of the tea plant. The PU/STL composites are fabricated through open molding method with a fiber loading of 16 wt. %. The fabricated composites are then subjected to physical and sound absorption testing as well as microscopic observations to analyze the distribution of filler in composite. The study shows that as-received FIBER-FAE spent tea leaves provide the best sound absorption coefficient and for composites using granulated fibers from any grade have lower sound absorption coefficient. These results show that a novel kind of sound absorption materials with the recycling of waste materials can be obtained for the solution of noise and environmental pollution.

scholarly journals The Effects of Various Additive Components on the Sound Absorption Performances of Polyurethane Foams

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Shuming Chen ◽  
Yang Jiang ◽  
Jing Chen ◽  
Dengfeng Wang
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Transmission Loss ◽  
Polyurethane Foams ◽  
Acoustic Properties ◽  
Acoustic Absorption ◽  
Absorption Properties ◽  
Maximum Enhancement ◽  
Flexible Polyurethane ◽  
Pu Foams

Flexible polyurethane (PU) foams comprising various additive components were synthesized to improve their acoustic performances. The purpose of this study was to investigate the effects of various additive components of the PU foams on the resultant sound absorption, which was characterized by the impedance tube technique to obtain the incident sound absorption coefficient and transmission loss. The maximum enhancement in the acoustic properties of the foams was obtained by adding fluorine-dichloroethane (141b) and triethanolamine. The results showed that the acoustic absorption properties of the PU foams were improved by adding 141b and triethanolamine and depended on the amount of the water, 141b, and triethanolamine.

Analysis of Sound Absorption Properties of Three-Leaf Microperforated Panel Absorbers without a Rigid Backing

2014 ◽  
Vol 937 ◽  
pp. 465-471
Author(s):  
Xiao Ling Gai ◽  
Xian Hui Li ◽  
Rui Wu ◽  
Bin Zhang ◽  
Jun Juan Zhao
Keyword(s):  
Sound Absorption ◽  
Low Frequency ◽  
Wide Frequency Range ◽  
Structure Design ◽  
Frequency Region ◽  
Theoretical Development ◽  
Frequency Range ◽  
Absorption Properties ◽  
High Frequency Region ◽  
Energy Dissipated

Microperforated panel (MPP) absorbers have been developed rapidly and used in many fields in recent years. First, based on the Maa’s theory, the theoretical development of MPP is reviewed in this paper. Furthermore, structure design and processing technology of MPP are introduced. Finally, the further development of MPP is discussed. Based on the MPP theory and electro-acoustical equivalent circuit principle, sound absorption properties of three-leaf microperforated panel (TMPP) absorbers without a rigid backing are studied to broaden the sound absorption bandwidth of MPP structure. Simulation results show that TMPP absorbers without a rigid backing have two resonance peaks and the energy dissipated coefficient remains constant in the low frequency range. The resonance frequency moves toward low frequency region with the increasing of the distance, thickness and pore diameter of MPP and moves toward high frequency region with the increasing of the perforation when other parameters keep invariant. The energy dissipated coefficient more than 0.5 over 8 octaves by choosing proper parameters. In conclusion, TMPP absorbers without a rigid backing have good sound absorption properties in a wide frequency range.

Sign in / Sign up

Export Citation Format

Share Document