scholarly journals Preliminary design of a management maintenance model of sensitive engineering assets, for a ship under the concept of reliability engineering

2020 ◽  
Vol 14 (27) ◽  
pp. 9-23
Author(s):  
Jorge Cárdenas Molina ◽  
Ivonne Olguín Valenzuela
Keyword(s):  
Continuous Improvement ◽  
Iterative Process ◽  
Failure Modes ◽  
Preliminary Design ◽  
Reliability Engineering ◽  
Engineering Department ◽  
Dynamic Maintenance ◽  
The Impact ◽  
Maintenance Model

The objective of this research is to apply a dynamic maintenance model to the assets of the engineering department of a navy vessel, based on the concept of reliability engineering, which analyzes the statistics of failures of different equipment, in a period of 140 months, in order to determine which is the most sensible equipment, the failure modes and the impact it produces on the ship’s platform. This way, it is possible to focus on the problems that produce the biggest impact in the capacity of the Unit´s, in order to fulfill its roles, and this way, contribute increase its availability. This is an iterative process of continuous improvement for the maintenance plans.

scholarly journals Experimental Study on the Mechanical Properties and Compression Size Effect of Recycled Aggregate Concrete

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2323
Author(s):  
Yubing Du ◽  
Zhiqing Zhao ◽  
Qiang Xiao ◽  
Feiting Shi ◽  
Jianming Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Size Effect ◽  
Compressive Stress ◽  
Failure Modes ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Aggregate Concrete ◽  
Substitution Ratio ◽  
The Impact

To explore the basic mechanical properties and size effects of recycled aggregate concrete (RAC) with different substitution ratios of coarse recycled concrete aggregates (CRCAs) to replace natural coarse aggregates (NCA), the failure modes and mechanical parameters of RAC under different loading conditions including compression, splitting tensile resistance and direct shear were compared and analyzed. The conclusions drawn are as follows: the failure mechanisms of concrete with different substitution ratios of CRCAs are similar; with the increase in substitution ratio, the peak compressive stress and peak tensile stress of RAC decrease gradually, the splitting limit displacement decreases, and the splitting tensile modulus slightly increases; with the increase in the concrete cube’s side length, the peak compressive stress of RAC declines gradually, but the integrity after compression is gradually improved; and the increase in the substitution ratio of the recycled aggregate reduces the impact of the size effect on the peak compressive stress of RAC. Furthermore, an influence equation of the coupling effect of the substitution ratio and size effect on the peak compressive stress of RAC was quantitatively established. The research results are of great significance for the engineering application of RAC and the strength selection of RAC structure design.

Effect of long-term moisture exposure on impact response of glass-reinforced vinylester

2021 ◽  
pp. 147509022199616
Author(s):  
Fatemeh Alizadeh ◽  
Navid Kharghani ◽  
Carlos Guedes Soares
Keyword(s):  
Water Uptake ◽  
Failure Modes ◽  
Sea Water ◽  
Composite Plates ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Water Type ◽  
Interfacial Damage ◽  
Impact Properties ◽  
The Impact

Glass/Vinylester composite laminates are comprehensively characterised to assess its impact response behaviour under moisture exposure in marine structures. An instrumented drop weight impact machine is utilised to determine the impact responses of dry and immersed specimens in normal, salted and sea water. The specimens, which had three different thicknesses, were subjected to water exposure for a very long period of over 20 months before tested in a low-velocity impact experiment. Water uptake was measured primarily to study the degradation profiles of GRP laminates after being permeated by water. Matrix dissolution and interfacial damage observed on the laminates after prolonged moisture exposure while the absorption behaviour was found typically non-Fickian. The weight of the composite plates firstly increased because of water diffusion up to month 15 and then decreased due to matrix degradation. The specimens with 3, 6 and 9 mm thickness exhibited maximum water absorption corresponding to 2.6%, 0.7% and 0.5% weight gain, respectively. In general, the results indicated that water uptake and impact properties were affected by thickness and less by water type. Impact properties of prolonged immersed specimens reduced remarkably, and intense failure modes detected almost in all cases. The least sensitive to impact damage were wet specimens with 9 mm thickness as they indicated similar maximum load and absorbed energy for different impact energies.

Response and failure modes of biaxial warp-knitted flexible composite subject to low-velocity impact

2021 ◽  
pp. 152808372110154
Author(s):  
Ziyu Zhao ◽  
Tianming Liu ◽  
Pibo Ma
Keyword(s):  
Impact Energy ◽  
Linear Density ◽  
Failure Modes ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Minor Effect ◽  
Low Velocity ◽  
Velocity Impact ◽  
Flexible Composites ◽  
The Impact

In this paper, biaxial warp-knitted fabrics were produced with different high tenacity polyester linear density and inserted yarns density. The low-velocity impact property of flexible composites made of polyurethane as matrix and biaxial warp-knitted fabric as reinforcement has been investigated. The effect of impactor shape and initial impact energy on the impact response of flexible composite is tested. The results show that the initial impact energy have minor effect on the impact response of the biaxial warp-knitted flexible composites. The impact resistance of flexible composite specimen increases with the increase of high tenacity polyester linear density and inserted yarns density. The damage morphology of flexible composite materials is completely different under different impactor shapes. The findings have theoretical and practical significance for the applications of biaxial warp-knitted flexible composite.

Operation and approximation based on the history of failure modes recorded by SCADA system of Amougdoul Moroccan wind farm using FMECA maintenance model

2021 ◽  
pp. 0309524X2199245
Author(s):  
Kawtar Lamhour ◽  
Abdeslam Tizliouine
Keyword(s):  
Wind Turbines ◽  
Wind Farm ◽  
Failure Modes ◽  
Wind Farms ◽  
Scada System ◽  
History Of ◽  
Criticality Analysis ◽  
Maintenance Model ◽  
Reliability And Availability ◽  
Critical Subsystems

The wind industry is trying to find tools to accurately predict and know the reliability and availability of newly installed wind turbines. Failure modes, effects and criticality analysis (FMECA) is a technique used to determine critical subsystems, causes and consequences of wind turbines. FMECA has been widely used by manufacturers of wind turbine assemblies to analyze, evaluate and prioritize potential/known failure modes. However, its actual implementation in wind farms has some limitations. This paper aims to determine the most critical subsystems, causes and consequences of the wind turbines of the Moroccan wind farm of Amougdoul during the years 2010–2019 by applying the maintenance model (FMECA), which is an analysis of failure modes, effects and criticality based on a history of failure modes occurred by the SCADA system and proposing solutions and recommendations.

scholarly journals Evaluation of Energy Absorption Capabilities of Polyethylene Foam under Impact Deformation

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3613
Author(s):  
Baohui Yang ◽  
Yangjie Zuo ◽  
Zhengping Chang
Keyword(s):  
Energy Absorption ◽  
Failure Modes ◽  
High Strain ◽  
Early Stage ◽  
High Energy ◽  
Test Method ◽  
Test Theory ◽  
Strain Rates ◽  
Impact Properties ◽  
The Impact

Foams are widely used in protective applications requiring high energy absorption under impact, and evaluating impact properties of foams is vital. Therefore, a novel test method based on a shock tube was developed to investigate the impact properties of closed-cell polyethylene (PE) foams at strain rates over 6000 s−1, and the test theory is presented. Based on the test method, the failure progress and final failure modes of PE foams are discussed. Moreover, energy absorption capabilities of PE foams were assessed under both quasi-static and high strain rate loading conditions. The results showed that the foam exhibited a nonuniform deformation along the specimen length under high strain rates. The energy absorption rate of PE foam increased with the increasing of strain rates. The specimen energy absorption varied linearly in the early stage and then increased rapidly, corresponding to a uniform compression process. However, in the shock wave deformation process, the energy absorption capacity of the foam maintained a good stability and exhibited the best energy absorption state when the speed was higher than 26 m/s. This stable energy absorption state disappeared until the speed was lower than 1.3 m/s. The loading speed exhibited an obvious influence on energy density.

scholarly journals Dynamic maintenance model for high average-utility pattern mining with deletion operation

2021 ◽  
Author(s):  
Jimmy Ming-Tai Wu ◽  
Qian Teng ◽  
Shahab Tayeb ◽  
Jerry Chun-Wei Lin
Keyword(s):  
Pattern Mining ◽  
Computational Cost ◽  
Practical Applications ◽  
Itemset Mining ◽  
Dynamic Databases ◽  
Speed Up ◽  
Dynamic Maintenance ◽  
Average Utility ◽  
High Utility ◽  
Maintenance Model

AbstractThe high average-utility itemset mining (HAUIM) was established to provide a fair measure instead of genetic high-utility itemset mining (HUIM) for revealing the satisfied and interesting patterns. In practical applications, the database is dynamically changed when insertion/deletion operations are performed on databases. Several works were designed to handle the insertion process but fewer studies focused on processing the deletion process for knowledge maintenance. In this paper, we then develop a PRE-HAUI-DEL algorithm that utilizes the pre-large concept on HAUIM for handling transaction deletion in the dynamic databases. The pre-large concept is served as the buffer on HAUIM that reduces the number of database scans while the database is updated particularly in transaction deletion. Two upper-bound values are also established here to reduce the unpromising candidates early which can speed up the computational cost. From the experimental results, the designed PRE-HAUI-DEL algorithm is well performed compared to the Apriori-like model in terms of runtime, memory, and scalability in dynamic databases.

scholarly journals IMPROVING THE RELIABILITY OF BODY ASSEMBLY LINE EQUIPMENT

1996 ◽  
Vol 03 (01) ◽  
pp. 11-24 ◽  
Author(s):  
KAKURO AMASAKA ◽  
HIROHISA SAKAI
Keyword(s):  
Conventional Method ◽  
Assembly Line ◽  
Failure Modes ◽  
Lead Times ◽  
Reliability Engineering ◽  
Production Lines ◽  
Line Production ◽  
Equipment Reliability ◽  
New Models ◽  
Short Time

It is necessary to establish higher levels of equipment reliability in a short time, the market demands ever shorter lead times for the release of new models. Also, the demand for new-model cars is very strong immediately after their introduction. The conventional method for enhancing equipment reliability is by screening alone. However, this requires screening operations on production lines and so has been an obstacle to line production and prevented shortening of lead times. We are now able to dramatically enhance equipment reliability in a very short time by detecting failure modes and forecasting the number of occurrences using a scientific technique based on reliability engineering.

Reliability Analysis of Great Lakes Marine Diesels: State of the Art and Current Modeling

1990 ◽  
Vol 27 (04) ◽  
pp. 237-249
Author(s):  
Anastassios N. Perakis ◽  
Bahadir Inozu
Keyword(s):  
Great Lakes ◽  
Diesel Engines ◽  
Failure Modes ◽  
State Of The Art ◽  
Relevant Literature ◽  
Fault Tree Analysis ◽  
Reliability Engineering ◽  
Marine Industry ◽  
Marine Diesel ◽  
Basic Concepts

Some essential steps for the application of reliability, availability, and maintainability (RAM) techniques to marine diesel engines are presented. The paper begins with a summary of the basic concepts of reliability engineering, followed by a survey of the relevant literature on RAM applications to the marine industry and to marine diesel engines in particular. Next, the results of an informal survey of the reliability, maintenance, and replacement practices of Great Lakes operators are presented. Finally, the first two steps for a RAM application, failure modes and effects analysis and fault tree analysis, are introduced and applied for a prototype Colt-Pielstick marine diesel engine.

Influence of Human Error on Structural Reliability

2017 ◽  
Author(s):  
Eric Brehm ◽  
Robert Hertle ◽  
Markus Wetzel
Keyword(s):  
Human Error ◽  
Structural Reliability ◽  
Failure Modes ◽  
Structural Model ◽  
Limit State ◽  
Design Procedure ◽  
Material Strength ◽  
Limit States ◽  
The Impact

In common structural design, random variables, such as material strength or loads, are represented by fixed numbers defined in design codes. This is also referred to as deterministic design. Addressing the random character of these variables directly, the probabilistic design procedure allows the determination of the probability of exceeding a defined limit state. This probability is referred to as failure probability. From there, the structural reliability, representing the survival probability, can be determined. Structural reliability thus is a property of a structure or structural member, depending on the relevant limit states, failure modes and basic variables. This is the basis for the determination of partial safety factors which are, for sake of a simpler design, applied within deterministic design procedures. In addition to the basic variables in terms of material and loads, further basic variables representing the structural model have to be considered. These depend strongly on the experience of the design engineer and the level of detailing of the model. However, in the clear majority of cases [1] failure does not occur due to unexpectedly high or low values of loads or material strength. The most common reasons for failure are human errors in design and execution. This paper will provide practical examples of original designs affected by human error and will assess the impact on structural reliability.

scholarly journals Maintenance Modelling of Ceramic Claddings in Pitched Roofs Based on the Evaluation of Their In Situ Degradation Condition

2020 ◽  
Vol 5 (9) ◽  
pp. 77
Author(s):  
Cláudia Ferreira ◽  
Ana Silva ◽  
Jorge de Brito ◽  
Ilídio S. Dias ◽  
Inês Flores-Colen
Keyword(s):  
Service Life ◽  
Maintenance Strategies ◽  
Total Replacement ◽  
Remaining Service Life ◽  
In Situ Degradation ◽  
Maintenance Policies ◽  
And Performance ◽  
The Impact ◽  
Maintenance Model

Existing maintenance policies have several limitations, mainly due to the lack of knowledge regarding the durability and performance of buildings. Usually, the maintenance policies are insufficiently accurate, neglecting the risk of failure over time and the global costs associated with repairs. In this study, a condition-based maintenance model, based on Petri nets, is proposed to evaluate the impact of three maintenance strategies of ceramic claddings in pitched roofs (CCPR): MS1—only total replacement; MS2—composed of total replacement and minor intervention and MS3—composed of total replacement, minor intervention and cleaning operations. In this study, 146 CCPR were inspected in situ, with a total area of 43,991.6 m2. The remaining service life of the CCPR; the global costs over the claddings’ lifetime (considering inspection, maintenance, replacement and disposal costs); the claddings’ degradation condition and the number of replacements during the time horizon are used to evaluate the performance of the different maintenance strategies through a simplified multi-criteria analysis. The results show that the gains in performance, in terms of expected service life and durability, of the consideration of preventive maintenance actions (minor interventions or cleaning operations) outweigh the increase of the operation costs.

Sign in / Sign up

Export Citation Format

Share Document