A study of flow separation on an aspect ratio three flap at Mach number 2.4

1991 ◽  
Author(s):  
MICHAEL COON ◽  
GARY CHAPMAN
Keyword(s):  
Mach Number ◽  
Aspect Ratio ◽  
Flow Separation

Performance Analysis of the Test Results on a Two-Stage Transonic Fan

1983 ◽  
Vol 105 (1) ◽  
pp. 125-129
Author(s):  
Baoshi Chen ◽  
Tianyi Zhang
Keyword(s):  
Mach Number ◽  
Performance Analysis ◽  
Radial Distribution ◽  
Flow Separation ◽  
High Load ◽  
Test Results ◽  
Two Stage ◽  
Stall Margin ◽  
High Incidence ◽  
Transonic Fan

Test results obtained from a two-stage fan are analysed and the reasons that caused the design performance target not to be attained are presented in this paper. Addition of a partspan shroud on rotor 1 caused higher losses and changed radial distribution of parameters. Modification on the flowpath and chord length of stator 1 resulted in excessively high inlet Mach number and flow separation in the hub region. The high load and high incidence at the hub of rotor 2 caused higher losses and reduced stall margin of the fan.

Measurements of Endwall Flows in Transonic Linear Turbine Cascades: Part II—High Flow Turning

2010 ◽  
Author(s):  
F. Taremi ◽  
S. A. Sjolander ◽  
T. J. Praisner
Keyword(s):  
Mach Number ◽  
Kinetic Energy ◽  
Flow Visualization ◽  
Flow Separation ◽  
Surface Flow ◽  
Streamwise Vorticity ◽  
Vortical Structures ◽  
Turbine Cascades ◽  
Mach Numbers ◽  
Surface Flow Visualization

An experimental investigation of two low-turning (90°) transonic linear turbine cascades was presented in Part I of the paper. Part II examines two high-turning (112°) turbine cascades. The experimental results include total pressure losses, streamwise vorticity and secondary kinetic energy distributions. The measurements were made using a seven-hole pressure probe downstream of the cascades. In addition to the measurements, surface flow visualization was conducted to assist in the interpretation of the flow physics. The turbine cascades in Part II, referred to as SL1F and SL2F, have the same inlet and outlet design flow angles, but different aerodynamic loading levels: SL2F is more highly loaded than SL1F. The surface flow visualization results show evidence of small flow separation on the suction side of both airfoils. At the design conditions (outlet Mach number ≈ 0.8), SL2F exhibits stronger vortical structures and larger secondary velocities than SL1F. The two cascades, however, produce similar row losses based on the measurements at 40% axial chord lengths downstream of the trailing edge. Additional data were collected at off-design outlet Mach numbers of 0.65 and 0.91. As the Mach number is raised, the cascades become more aft-loaded. The absolute blade loadings increase, but the Zweifel coefficients decrease due to higher outlet dynamic pressures. Both profile and secondary losses decrease at higher Mach numbers; the main vortical structures and the corresponding peak losses migrate towards the endwall, and there are reductions in secondary kinetic energy and exit flow angle variations. The streamwise vorticity distributions show smaller peak vorticities associated with the passage and the counter vortices at higher exit Mach numbers. The corner vortex, on the other hand, becomes more intensified, resulting in reduction of flow overturning near the endwall. The results for SL1F and SL2F are compared and contrasted with the results for the lower turning cascades presented in Part I. The possible effects of suction-surface flow separation on profile and secondary losses are discussed in this context. The current research project is part of a larger study concerning the effects of endwall contouring on secondary losses, which will be presented in the near future.

CFD Investigation of the Flow of Trailing Edge Cooling Slots

2018 ◽  
Author(s):  
Y. Jiang ◽  
N. Gurram ◽  
E. Romero ◽  
P. T. Ireland ◽  
L. di Mare
Keyword(s):  
Mach Number ◽  
Kinetic Energy ◽  
Flow Separation ◽  
Film Cooling ◽  
High Speed ◽  
Turbine Blades ◽  
Cross Flow ◽  
Turbulent Energy ◽  
Trailing Edge ◽  
Flow Interactions

Slot film cooling is a popular choice for trailing edge cooling in high pressure (HP) turbine blades because it can provide more uniform film coverage compared to discrete film cooling holes. The slot geometry consists of a cut back in the blade pressure side connected through rectangular openings to the internal coolant feed passage. The numerical simulation of this kind of film cooling flows is challenging due to the presence of flow interactions like step flow separation, coolant-mainstream mixing and heat transfer. The geometry under consideration is a cutback surface at the trailing edge of a constant cross-section aerofoil. The cutback surface is divided into three sections separated by narrow lands. The experiments are conducted in a high speed cascade in Oxford Osney Thermo-Fluids Laboratory at Reynolds and Mach number distributions representative of engine conditions. The capability of CFD methods to capture these flow phenomena is investigated in this paper. The isentropic Mach number and film effectiveness are compared between CFD and pressure sensitive paint (PSP) data. Compared to steady k–ω SST method, Scale Adaptive Simulation (SAS) can agree better with the measurement. Furthermore, the profiles of kinetic energy, production and shear stress obtained by the steady and SAS methods are compared to identify the main source of inaccuracy in RANS simulations. The SAS method is better to capture the unsteady coolant-hot gas mixing and vortex shedding at the slot lip. The cross flow is found to affect the film significantly as it triggers flow separation near the lands and reduces the effectiveness. The film is non-symmetric with respect to the half-span plane and different flow features are present in each slot. The effect of mass flow ratio (MFR) on flow pattern and coolant distribution is also studied. The profiles of velocity, kinetic energy and production of turbulent energy are compared among the slots in detail. The MFR not only affects the magnitude but also changes the sign of production.

Straight Channel Diffuser Performance at High Inlet Mach Numbers

1969 ◽  
Vol 91 (3) ◽  
pp. 397-412 ◽  
Author(s):  
P. W. Runstadler ◽  
R. C. Dean
Keyword(s):  
Mach Number ◽  
Aspect Ratio ◽  
Pressure Recovery ◽  
Straight Channel ◽  
Single Plane ◽  
Aspect Ratios ◽  
Straight Wall ◽  
Throat Width ◽  
Mach Numbers

Measurements have been made of the pressure recovery of straight wall, single plane divergence diffusers with inlet Mach numbers between 0.2 and choking (0.2 ≤ Mt < 1.0). In contrast to the widely held assertion in the literature, there is no “critical” inlet subsonic Mach number above which pressure recovery decreases drastically. Two aspect ratios, AS = 0.25 and 1.0, have been studied for a range of length-to-throat-width ratios L/W1 and divergence angles 2θ around the regions of peak recovery. Diffuser performance maps are given showing pressure recovery Cp as a function of diffuser geometry for fixed values of throat Mach number Mt, throat blockage B, and aspect ratio AS. Significant changes in the location and magnitude of pressure recovery do occur with variations in Mt, B, and AS. The importance to the designer of a knowledge of how diffuser performance depends upon geometric and diffuser inlet parameters is discussed.

Theory of low Mach number compressible flow in a channel

1996 ◽  
Vol 313 ◽  
pp. 131-145 ◽  
Author(s):  
A. Shajii ◽  
J. P. Freidberg
Keyword(s):  
Steady State ◽  
Mach Number ◽  
Aspect Ratio ◽  
Compressible Flow ◽  
Applied Pressure ◽  
Subsonic Flows ◽  
Low Mach Number ◽  
Large Channel ◽  
Channel Aspect Ratio ◽  
Compressibility Effects

The properties of a relatively uncommon regime of fluid dynamics, low Mach number compressible flow are investigated. This regime, which is characterized by an exceptionally large channel aspect ratio L/d ∼ 106 leads to highly subsonic flows in which friction dominates inertia. Even so, because of the large aspect ratio, finite pressure, temperature, and density gradients are required, implying that compressibility effects are also important. Analytical results are presented which show, somewhat unexpectedly, that for forced channel flow, steady-state solutions exist only below a critical value of heat input. Above this value the flow reverses against the direction of the applied pressure gradient causing fluid to leave both the inlet and outlet implying that the related concepts of a steady-state friction factor and heat transfer coefficient have no validity.

scholarly journals Investigation of the effects of main geometric parameters and flow characteristics on secondary flow losses in a turbine cascade

2021 ◽  
Vol 2131 (3) ◽  
pp. 032081
Author(s):  
M Mesbah ◽  
V G Gribin ◽  
K Souri
Keyword(s):  
Mach Number ◽  
Aspect Ratio ◽  
Total Energy ◽  
Flow Characteristics ◽  
Numerical Results ◽  
Energy Losses ◽  
Inlet Flow ◽  
Flow Angle ◽  
Flow Losses ◽  
Exit Mach Number

Abstract This paper presents numerical simulation results of a three-dimensional (3D) transitional flow in a stator cascade of an axial turbine. The influences of the main geometric parameters and flow characteristics including, the blade aspect ratio, pitch-to-chord ratio, inlet flow angle, and exit Mach number, on secondary flows development and end-wall losses, were studied. The numerical results were validated by the results of experiments conducted in the laboratory of the steam and gas turbine faculty of the Moscow Power Engineering Institute. The maximum difference between computed and experimental results was 2.4 %. The total energy losses decrease by 20 % when the exit Mach number changes from 0.38 to 0.8. Numerical results indicated that the blade aspect ratio had the most effect on secondary flow losses. The total energy losses increase by 46.6 % when the aspect ratio decreases from 1 to 0.25. The total loss of energy by 13.2 % decreases by increasing the inlet flow angle from 60 degrees to 90 degrees. Then by increasing the inlet flow angle from 90 to 110 degrees, the total loss rises by 3.6%. As the pitch-to-chord ratio increases from 0.7 to 0.75, the total energy losses are reduced by 12.2 %. Then by increasing the pitch-to-chord ratio from 0.75 to 0.8, the total energy losses increase by 6 %. As with experimental data, the numerical results showed that the optimal inlet flow angle and relative pitch for the cascade are 90 degrees and 0.75, respectively.

scholarly journals Numerical simulation of NACA4412 airfoil in pre-stall conditions

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Vincent Gleize ◽  
Michel Costes ◽  
Ivan Mary
Keyword(s):  
Numerical Simulation ◽  
Reynolds Number ◽  
Mach Number ◽  
Skin Friction ◽  
Flow Separation ◽  
Turbulent Mixing ◽  
Design Methodology ◽  
Freestream Velocity ◽  
Content Type ◽  
Laminar Separation

Purpose The purpose of this paper is to study turbulent flow separation at the airfoil trailing edge. This work aims to improve the knowledge of stall phenomenon by creating a QDNS database for the NACA412 airfoil. Design/methodology/approach Quasi-DNS simulations of the NACA 4412 airfoil in pre-stall conditions have been completed. The Reynolds number based on airfoil chord and freestream velocity is equal to 0.35 million, and the freestream Mach number to 0.117. Transition is triggered on both surfaces for avoiding the occurrence of laminar separation bubbles and to ensure turbulent mixing in the wake. Four incidences have been considered, 5, 8 10 and 11 degrees. Findings The results obtained show a reasonably good correlation of the present simulations with classical MSES airfoil simulations and with RANS computations, both in terms of pressure and skin-friction distribution, with an earlier and more extended flow separation in the QDNS. The database thus generated will be deeply analysed and enriched for larger incidences in the future. Originality/value No experimental or HPC numerical database at reasonable Reynolds number exists in the literature. The current work is the first step in that direction.

Sign in / Sign up

Export Citation Format

Share Document