scholarly journals Malachite Green Removal by Zn/Al-citrate LDHs in Aqueous Solution

2020 ◽  
Vol 5 (2) ◽  
pp. 59
Author(s):  
Nurlisa Hidayati ◽  
Risfidian Mohadi ◽  
Elfita Elfita ◽  
Aldes Lesbani
Keyword(s):  
Aqueous Solution ◽  
Malachite Green ◽  
Adsorption Process ◽  
Langmuir Adsorption Isotherm ◽  
Precipitation Method ◽  
Chemical Adsorption ◽  
Langmuir Adsorption ◽  
Batch System ◽  
Isotherm Adsorption ◽  
Co Precipitation

Zn/Al-citrate LDHs was synthesized using co precipitation method at basic condition and the material were applied as adsorbent of malachite green (MG) dye in aqueous medium using batch system. Adsorption of MG onto Zn/Al-citrate was investigated through kinetic, isotherm adsorption and thermodynamic studies. Kinetic model was fitted PSO than PFO for MG adsorption. The rate of adsorption 𝑘2 for Zn/Al LDHs was 0.000692 g.mg−1 min−1 and 0.000371 g for Zn/Al-citrate LDHs.mg−1 min−1. Adsorption of malachite green onto Zn/Al LDHs and Zn/Al citrate LDHs was investigated and following Langmuir adsorption isotherm model shows chemical adsorption process. The adsorption capacity maximum of Zn/Al-citrate is 333 mg/g from Zn/Al LDHs is only 111 mg/g. Thermodynamic parameters of Zn/Al-citrate confirmed adsorption process was endothermic and spontaneous.

scholarly journals Adsorptive Capacity of Malachite Green onto Mg/M3+ (M3+=Al and Cr) LDHs

2021 ◽  
Keyword(s):  
Aqueous Solution ◽  
Malachite Green ◽  
High Stability ◽  
Adsorption Process ◽  
Adsorptive Capacity ◽  
Xrd Pattern ◽  
Langmuir Adsorption ◽  
Stability Structure ◽  
Pseudo Second Order ◽  
Double Hydroxides

<p>Layered double hydroxides (LDHs) of MgM3+ (M3+=Al and Cr) were synthesized by coprecipitation method to form Mg/Al and Mg/Cr LDHs. The materials were applied as adsorbents of malachite green in aqueous solution. The physical properties of Mg/Al and Mg/Cr were analyzed using XRD, FTIR, BET and TGDTA characterizations. The XRD pattern shows the characteristic of LDHs which has diffraction at 11.470 (003) and at 34.690 (012) for Mg/Al and 12.450 (003) and at 380 (012) for Mg/Cr. The interlayer spaces of Mg/Al and Mg/Cr LDHs were 7.71 Å and 7.62 Å, respectively. The surface area of Mg/Al was higher than Mg/Cr. The FTIR spectra confirm that the intense peak at 1385 cm-1 denotes vibration of nitrate bond and M-O band in under 1000 cm-1. Thus the Mg/Al and Mg/Cr LDHs were applied as adsorbents to remove malachite green in aqueous solution. The results of malachite green adsorption showed that malachite green was adsorbed onto Mg/Al and Mg/Cr followed pseudo second order and Langmuir adsorption parameter. The adsorption capacity of malachite green for Mg/Al and Mg/Cr was 44.444 mg/g and 33.784 mg/g, respectively. The thermodynamic study showed that the adsorption process was spontaneous, endothermic and favored in high temperature. The regeneration process showed that Mg/Al and Mg/Cr LDHs has high stability structure toward reusability of adsorbent until three cycles adsorption process.</p>

scholarly journals ADSORPTION OF GIBBERELLIC ACID ONTO NATURAL KAOLIN FROM TATAKAN, SOUTH KALIMANTAN

2010 ◽  
Vol 9 (3) ◽  
pp. 373-379 ◽  
Author(s):  
Sunardi Sunardi ◽  
Yateman Arryanto ◽  
Sutarno Sutarno
Keyword(s):  
Adsorption Isotherm ◽  
Gibberellic Acid ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Langmuir Adsorption Isotherm ◽  
Purification Process ◽  
X Ray ◽  
Langmuir Adsorption ◽  
Batch System

Adsorption of gibberellic acid (GA3) onto raw and purified kaolin from Tatakan, South Kalimantan was investigated in this study. Purification process was done by sedimentation to obtain relative pure kaolinite. Raw and purified kaolin samples were characterized by Fourier transformed infrared (FTIR) spectroscopy and X-ray diffractometer (XRD). The adsorption process was carried out in a batch system and the effect of pH, contact time and GA3 concentration were experimentally studied to evaluate the adsorption capacity. The amount of GA3 adsorbed was determined by UV spectrophotometer. The result showed that the raw kaolin from South Kalimantan consist of 53.36% kaolinite, 29.47% halloysite, 4.47% chlorite, 11.32% quartz and 1.38% christobalite and the purified kaolin consist of 73.03% kaolinite, 22.6% halloysite, 0.77% chlorite, 1.37% quartz and 2.23% christobalite Adsorption experimental indicate that the optimum adsorption took place at pH 7 and contact time for 4 h. Adsorption of GA3 was described by the Langmuir adsorption isotherm model with adsorption capacity of 8.91 mg/g on raw kaolin and 10.38 mg/g on purified kaolin.   Keywords: kaolin, gibberellic acid, adsorption

scholarly journals Removal of methylene blue from aqueous solution using Mg-Fe, Zn-Fe, Mn-Fe layered double hydroxide

2020 ◽  
Vol 81 (12) ◽  
pp. 2522-2532
Author(s):  
Zhongliang Shi ◽  
Yanmei Wang ◽  
Shuyu Sun ◽  
Cheng Zhang ◽  
Haibo Wang
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Langmuir Adsorption ◽  
Molar Ratios ◽  
Pseudo Second Order ◽  
Co Precipitation ◽  
Double Hydroxide ◽  
Double Hydroxides

Abstract Layered double hydroxides (LDH) with highly flexible and adjustable chemical composition and physical properties have attracted tremendous attention in recent years. A series of LDH with different M (Mg, Zn, Mn)-Fe molar ratios were synthesized by the double titration co-precipitation method. The effect of the factors, including M (Mg, Zn, Mn) : Fe molar ratio, pH, and M-Fe LDH dosage, on the ability of the prepared M-Fe LDH to remove cationic methylene blue (MB) dye from aqueous solution were investigated. Results indicated that the removal efficiency of MB (10 mg/L) was the best at the M (Mg, Zn, Mn): Fe molar ratio of 3:1 by using 2.0 g/L of M-Fe LDH at pH 6.0 under 298.15 K. Mg-Fe LDH had the highest removal performance (71.94 mg/g at 298.15 K) for MB compared to those of the Zn-Fe and Mn-Fe LDH. Zn-Fe LDH with the smallest activation energy resulted in the fastest adsorption rate of MB. The pseudo-second-order model and Langmuir adsorption isotherm were also successfully applied to fit the theory of M-Fe LDH for removal of MB.

scholarly journals Modification of Cu/Cr Layered Double Hydroxide by Keggin Type Polyoxometalate as Adsorbent of Malachite Green from Aqueous Solution

2021 ◽  
Vol 6 (3) ◽  
pp. 209-217
Author(s):  
Neza Rahayu Palapa ◽  
Tarmizi Taher ◽  
Alfan Wijaya ◽  
Aldes Lesbani
Keyword(s):  
Aqueous Solution ◽  
Malachite Green ◽  
Adsorption Process ◽  
Order Kinetic ◽  
Keggin Type ◽  
Isotherm Adsorption ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Double Hydroxide ◽  
Double Hydroxides

Modification of Cu/Cr layered double hydroxides (LDHs) has been conducted by intercalation using Keggin type polyoxometalate [a-SiW12O40]4- to form CuCr-[a-SiW12O40]. The materials were analyzed by XRD, FTIR, and surface area analyses. Furthermore, materials were used as selectivity adsorbents of cationic dyes such as malachite green, rhodamine-B and methylene blue. The malachite green is more selective than others from an aqueous solution. The adsorption of malachite green showed that the adsorption capacity of CuCr-[a-SiW12O40] was higher than pristine LDHs. The adsorption process was followed pseudo second order kinetic model and Langmuir isotherm adsorption. The Qmax value of CuCr-[a-SiW12O40] reached 55.322 mg/g at 323 K after 100 minutes adsorption time. Thermodynamic parameters such as ΔG, ΔH and ΔS confirm that the adsorption process was endothermic, spontaneous, and more favorable at high temperatures. The intercalated material was higher structural stability toward reusability adsorbent than pristine LDHs.

scholarly journals Equilibrium, Kinetics, and Thermodynamic Studies of Malachite Green Adsorption onto Fig (Ficus cartia) Leaves

2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Yemane Tadesse Gebreslassie
Keyword(s):  
Activated Carbon ◽  
Adsorption Isotherm ◽  
Malachite Green ◽  
Contact Time ◽  
Adsorption Process ◽  
Langmuir Adsorption Isotherm ◽  
Experimental Result ◽  
Solution Temperature ◽  
Batch Adsorption ◽  
Langmuir Adsorption

The release of dyes from dying industries such as leather, paper, and textiles is an important cause of environmental pollution. In the present study, the batch adsorption measurements were carried out using stimulated aqueous solutions and the effect of operating variables such as initial malachite green concentration, amount of adsorbent, solution pH, contact time, and solution temperature, were investigated. The experimental result showed that the percentage removal decreased with an increase in initial dye concentration but increased as pH of the solution, contact time, and adsorbent dose increased. The equilibrium data were analyzed using Langmuir adsorption isotherm, Freundlich adsorption isotherm, and Tempkin isotherm models, and it was observed that the Langmuir adsorption isotherm better described the adsorption process. The monolayer adsorption capacity of activated carbon prepared from fig leaves for malachite green adsorption was found to be 51.79 mg/g at 298 K. Furthermore, the adsorption kinetics of the dye was investigated, and the rate of adsorption was found to follow the pseudo-first-order kinetic model with intraparticle diffusion as one of the rate-determining steps. The negative value of ΔG0 and the positive values of ΔH0 indicate the spontaneous and endothermic nature of the adsorption process, respectively. The experimental result obtained in the present study and comparison with other reported adsorbents indicate that activated carbon prepared from fig leaves could be used as a low-cost alternative adsorbent for the removal of malachite green from aqueous solution.

Photocatalytic Activity of Fe-Doped ZnO/Montmorillonite Nanocomposite for Degradation of Malachite Green

2015 ◽  
Vol 827 ◽  
pp. 19-24 ◽  
Author(s):  
Nur Afifah ◽  
Nadia Febiana Djaja ◽  
Rosari Saleh
Keyword(s):  
Photocatalytic Activity ◽  
Malachite Green ◽  
Organic Dyes ◽  
Uv Light ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Spin Resonance ◽  
Doped Zno ◽  
Co Precipitation

In this study, the photocatalytic activity of pure Fe- doped ZnO and Fe- doped ZnO/Montmorillonite nanocomposite has been investigated for the degradation of malachite green under UV light irradiation. Both photocatalysts were synthesized using co-precipitation method and characterized by X-ray diffraction, energy dispersive X-ray spectroscopy, Fourier-transform infrared absorption, and electron spin resonance. The results showed that the photocatalytic efficiency is better in the presence of montmorillonite compared to pure Fe- doped ZnO. To detect the possible reactive species involved in degradation of organic dyes control experiments with introducing scavengers into the solution of organic dyes were carried out. It is found that electron plays an important role in the degradation of malachite green.

scholarly journals Comparative Study on the Adsorption of [AuCl4]– onto Salicylic Acid and Gallic Acid Modified Magnetite Particles

2018 ◽  
Vol 16 (3) ◽  
pp. 329 ◽  
Author(s):  
Maya Rahmayanti ◽  
Sri Juari Santosa ◽  
Sutarno Sutarno
Keyword(s):  
Salicylic Acid ◽  
Gallic Acid ◽  
Adsorption Process ◽  
Freundlich Isotherms ◽  
Precipitation Procedure ◽  
Initial Ph ◽  
Isotherm Adsorption ◽  
Pseudo Second Order ◽  
Magnetite Particles ◽  
Co Precipitation

Salicylic acid-modified magnetite (Mag-SA) and gallic acid-modified magnetite (Mag-GA) particles were prepared by co-precipitation procedure. Characterization results showed the interaction that occurs between the surface of magnetite with salicylic acid (Mag-SA) and gallic acid (Mag-GA) was through hydrogen bonding. Adsorption of [AuCl4]– onto Mag-SA and Mag-GA surfaces as a function of initial pH, contact time, and initial concentration of the [AuCl4]– solution were comparatively investigated. Result showed that the optimum adsorption of [AuCl4]– onto Mag-SA or Mag-GA was found at pH 3. The adsorption process were found to allow the pseudo-second order equation, both for Mag-SA and Mag-GA. The parameters in isotherm adsorption equations conformed to the Langmuir and Freundlich isotherms very well for Mag-GA, but for Mag-SA, only conformed to the Langmuir isotherm very well. The result of this study demonstrate that the ability Mag-GA to adsorb [AuCl4]– higher than Mag-SA.

scholarly journals Baker’s yeast-MnO2 composites as biosorbent for Malachite green: An ecofriendly approach for dye removal from aqueous solution

2018 ◽  
Vol 14 (1) ◽  
pp. 1
Author(s):  
Bruna Assis Paim dos Santos ◽  
Aline Silva Cossolin ◽  
Hélen Cristina Oliveira dos Reis ◽  
Ketinny Camargo de Castro ◽  
Evanleide Rodrigues da Silva ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Malachite Green ◽  
Dye Removal ◽  
Adsorption Process ◽  
Baker’S Yeast ◽  
Baker's Yeast ◽  
Direct Oxidation ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Biomass Dosage

In this study, baker’s yeast-MnO2 composites, produced by direct oxidation of yeast with KMnO4 under acidic conditions, were used as biosorbent to remove the triphenylmethane dye Malachite green (MG) from an aqueous solution. Parameters that influence the adsorption process, such as pH, contact time, temperature, initial dye concentration and biosorbent dosage, were evaluated in batch experiments. The optimum removal of MG was found to be  86.7 mg g-1 at pH 10, 1.0 g L-1 of biomass dosage and 45°C. The kinetic data of dye removal was better described by the pseudo-second-order model. The adsorption process followed the Langmuir isotherm model and the maximum biosorption capacity was estimated to be  243.9 mg g-1 (at 25°C). The negative values of ∆G° and the positive value of ∆H° indicated that the MG biosorption onto yeast-MnO2 composites is spontaneous and endothermic. Fourier transform infrared spectroscopy (FTIR) indicated that the nano-MnO2 particles deposited on yeast-MnO2 composites surface facilitated the MG adsorption. It was concluded that baker’s yeast-MnO2 composites have potential for application as adsorbent for removal of MG from aqueous solution.

Study on Adsorption of U(VI) From Aqueous Solution by Activated MgO

2017 ◽  
Author(s):  
Qingqing Liu ◽  
Xiaoyan Li
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Removal Rate ◽  
Freundlich Isotherm ◽  
Batch System ◽  
15Mg Dose ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Kinetics Of

The activated MgO was synthesized by microwave homo-precipitator method and characterized by SEM, EDS and FT-IR methods. It was used to adsorption of U(VI) from aqueous solution with batch system. The paper discussed the effect of pH, temperature, contact time, adsorbent dose and initial U(VI) concentration on the adsorption. The results showed that activated MgO has good adsorption capacity for U(VI), the removal rate and equilibrium adsorption capacity reached 83.5% and 84.04mg·g−1 at pH 5.0, 15mg dose and 313K,respectively. The adsorption kinetics of U(VI) onto activated MgO were better fitted with pseudo-second-order kinetic.The adsorption isotherm data were fitted well to Freundlich isotherm model.The thermodynamic parameters showed that the adsorption process is endothermic and spontaneous.

Adsorptive removal of PPCPs by biomorphic HAP templated from cotton

2016 ◽  
Vol 74 (1) ◽  
pp. 276-286 ◽  
Author(s):  
Bin Huang ◽  
Dan Xiong ◽  
Tingting Zhao ◽  
Huan He ◽  
Xuejun Pan
Keyword(s):  
Adsorption Mechanism ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Precipitation Method ◽  
Adsorptive Removal ◽  
Transmission Electron ◽  
Initial Ph ◽  
Pseudo Second Order ◽  
Co Precipitation

Biomorphic nano-hydroxyapatite (HAP) was fabricated by a co-precipitation method using cotton as bio-templates and employed in adsorptive removal of ofloxacin (OFL) and triclosan (TCS) that are two representative pharmaceuticals and personal care products (PPCPs). The surface area and porosity, crystal phase, functional group, morphology and micro-structure of the synthesized HAP were characterized by Brunauer–Emmett–Teller isotherm, X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron macroscopic and transmission electron microscopy. The effects of initial pH, ionic strength, initial concentration, contact time and temperature on the removal of PPCPs were studied in a batch experiment. The adsorption of OFL and TCS was rapid and almost accomplished within 50 min. Kinetic studies indicated that the adsorption process of OFL and TCS followed the pseudo-first-order and pseudo-second-order models, respectively. The Freundlich isotherm described the OFL adsorption process well but the adsorption of TCS fitted the Langmuir isotherm better. Thermodynamics and isotherm parameters suggested that both OFL and TCS adsorption were feasible and spontaneous. Hydrogen bond and Lewis acid–base reaction may be the dominating adsorption mechanism of OFL and TCS, respectively. Compared to other adsorbents, biomorphic HAP is environmentally friendly and has the advantages of high adsorption capacity, exhibiting potential application for PPCPs removal.

Sign in / Sign up

Export Citation Format

Share Document