scholarly journals Perancangan Alat Pembuangan Abu Pada Gasifier Sistem Kontinu Berbahan Bakar Tongkol Jagung

2021 ◽  
Vol 1 (2) ◽  
pp. 102
Author(s):  
Noviyanti Nugraha ◽  
Muhammad Pramuda Sirodz ◽  
Benardino Hadiwijaya
Keyword(s):  
Fly Ash ◽  
Key Words ◽  
Electric Motor ◽  
Alternative Energy ◽  
Bottom Ash ◽  
Biomass Energy ◽  
Screw Conveyor ◽  
Ansys Software ◽  
Great Opportunity ◽  
Screw Diameter

Abstrak   Indonesia membutuhkan energi alternatif yang berpeluang besar untuk dikembangkan pemanfaatannya, salah satunya adalah energi biomassa yang berasal dari jagung. Pada penelitian sebelumnya sudah dirancang dan dibuat sistem gasifikasi kontinu, tetapi masih terdapat kekurangan pada pemisahan abu setelah pembakaran. Tujuan dari penelitian ini adalah untuk merancang sistem pemisah abu pada sistem gasifikasi kontinu sehingga didapatkan spesifikasi dari sistem pemisah abu tersebut. Sistem pemisah abu yang dirancang adalah screw conveyor untuk memisahkan bottom ash dan siklon untuk memisahkan fly ash. Hasil perancangan diperoleh spesifikasi yang dibutuhkan yaitu diameter screw sebesar 6 inci, motor listrik yang digunakan memiliki daya 1 HP, putaran screw sebesar 0,31 rpm dan poros screw conveyor sebesar 2 inci. Dengan standar yang sudah diberikan, dengan mengasumsikan diameter body siklon sebesar 0,1 m maka diperoleh seluruh dimensi siklon. Dengan diameter sebesar 0,1 m secara perhitungan didapat efisiensi siklon sebesar 78% dan secara simulasi menggunakan software ANSYS didapat efisiensi sebesar 80%. Kata kunci: tongkol jagung, gasifikasi, screw conveyor, siklon, ANSYS Abstract   Indonesia needs alternative energy that has a great opportunity to be developed its utilization, one of which is biomass energy derived from corn. In previous studies, a continuous gasification system has been designed and built, but there are still deficiencies in the separation of ash after combustion. The purpose of this research is to design an ash separator system in a continuous gasification system so that the specifications of the ash separator system can be obtained. The ash separator system designed is a screw conveyor for separating bottom ash and cyclones for separating fly ash. The design results obtained the required specifications,  the screw diameter is 6 inches, the electric motor used has a power of 1 HP, the screw rotation is 0.31 rpm and the screw conveyor shaft is 2 inches. With the standards that have been given, assuming the diameter of the cyclone body is 0.1 m, all the dimensions of the cyclone are obtained. With a diameter of 0.1 m, the calculation is that the cyclone efficiency is 78% and by simulation using the ANSYS software, the efficiency is 80%. Key words: corn cobs, gasification, screw conveyor, cyclone, ANSYS

Characterization of lead-bearing phases in municipal waste combustor fly ash

1996 ◽  
Vol 54 ◽  
pp. 516-517
Author(s):  
L. L. Sutter ◽  
G. R. Dewey ◽  
J. F. Sandell
Keyword(s):  
Fly Ash ◽  
Bottom Ash ◽  
Municipal Waste ◽  
Primary Concern ◽  
Leaching Behavior ◽  
Waste Combustion ◽  
Lead And Cadmium ◽  
Lead Speciation ◽  
Accepted Practice

Municipal waste combustion typically involves both energy recovery as well as volume reduction of municipal solid waste prior to landfilling. However, due to environmental concerns, municipal waste combustion (MWC) has not been a widely accepted practice. A primary concern is the leaching behavior of MWC ash when it is stored in a landfill. The ash consists of a finely divided fly ash fraction (10% by volume) and a coarser bottom ash (90% by volume). Typically, MWC fly ash fails tests used to evaluate leaching behavior due to high amounts of soluble lead and cadmium species. The focus of this study was to identify specific lead bearing phases in MWC fly ash. Detailed information regarding lead speciation is necessary to completely understand the leaching behavior of MWC ash.

Renewable Energy on Tribal Lands: A Feasibility Study for a Biomass-to-Energy Plant on the Cocopah Reservation in Arizona

2019 ◽  
Vol 3 (1) ◽  
pp. 1-12
Author(s):  
Lauren K. D’Souza ◽  
William L. Ascher ◽  
Tanja Srebotnjak
Keyword(s):  
Renewable Energy ◽  
Alternative Energy ◽  
Renewable Energy Sources ◽  
The United States ◽  
Biomass Energy ◽  
Policy Support ◽  
Small Scale ◽  
Energy Plant ◽  
Energy Projects ◽  
Alternative Investment

Native American reservations are among the most economically disadvantaged regions in the United States; lacking access to economic and educational opportunities that are exacerbated by “energy insecurity” due to insufficient connectivity to the electric grid and power outages. Local renewable energy sources such as wind, solar, and biomass offer energy alternatives but their implementation encounters barriers such as lack of financing, infrastructure, and expertise, as well as divergent attitudes among tribal leaders. Biomass, in particular, could be a source of stable base-load power that is abundant and scalable in many rural communities. This case study examines the feasibility of a biomass energy plant on the Cocopah reservation in southwestern Arizona. It considers feedstock availability, cost and energy content, technology options, nameplate capacity, discount and interest rates, construction, operation and maintenance (O&M) costs, and alternative investment options. This study finds that at current electricity prices and based on typical costs for fuel, O&M over 30 years, none of the tested scenarios is presently cost-effective on a net present value (NPV) basis when compared with an alternative investment yielding annual returns of 3% or higher. The technology most likely to be economically viable and suitable for remote, rural contexts—a combustion stoker—resulted in a levelized costs of energy (LCOE) ranging from US$0.056 to 0.147/kWh. The most favorable scenario is a combustion stoker with an estimated NPV of US$4,791,243. The NPV of the corresponding alternative investment is US$7,123,380. However, if the tribes were able to secure a zero-interest loan to finance the plant’s installation cost, the project would be on par with the alternative investment. Even if this were the case, the scenario still relies on some of the most optimistic assumptions for the biomass-to-power plant and excludes abatement costs for air emissions. The study thus concludes that at present small-scale, biomass-to-energy projects require a mix of favorable market and local conditions as well as appropriate policy support to make biomass energy projects a cost-competitive source of stable, alternative energy for remote rural tribal communities that can provide greater tribal sovereignty and economic opportunities.

VALUE INCREASING OF REJECT COAL WITH BIOMASS ADDING AS BIO-COAL BRIQUETTE

2020 ◽  
Vol 3 (2) ◽  
pp. 123
Author(s):  
Dyah Marganingrum ◽  
Lenny Marilyn Estiaty
Keyword(s):  
Alternative Energy ◽  
Ignition Time ◽  
Bottom Ash ◽  
Calorific Value ◽  
Added Value ◽  
Physical Test ◽  
Chemical Test ◽  
Agglomeration Process ◽  
Strategic Solution ◽  
Index Value

Aim: This paper aims to explain the added value increasing method of reject coal which has not utilized by the company. Methodology and Results: The method to increase added value in this study used the agglomeration process of briquettes form that changing composition by adding biomass. The biomass functions to minimize bottom ash produced from burning briquettes so that the briquettes burn entirely. Stages processes in this study consist of characterization, briquetting, physical test, and chemical test. Based on the analysis, reject coal still has a high calorific value of 5,929 cal/gr. Shapes and sizes that were not following needs of coal market or consumer due to reject coal to be a waste. Briquettes have been successfully produced and meet specification requirements based on applicable regulations in Indonesia. Besides physical properties, the briquette meet density requirements which are greater than or equal to 1 gr/cm3 and shatter index value is less than 0.5%. The gas emission test shows below threshold, which is CO 0-30 ppm, H2S 0-3.6 ppm, and NOx is not detected. After evaluation, it showed that by adding 30% biomass, ignition time could be decreased and remaining unburned briquettes or bottom ash was reduced as much as 68.68%. Conclusion, significance and impact study: The bio-coal briquettes is a strategic solution to environmental problems and alternative energy sources that are environmentally friendly, because CO and H2S emissions are still below the threshold, even for NOx not detected. Making Bio-coal briquettes as a solution to the utilization of reject coal mining waste to be used as an alternative energy source has been successfully carried out.

scholarly journals Ternary Mixes of Self-Compacting Concrete with Fly Ash and Municipal Solid Waste Incinerator Bottom Ash

2020 ◽  
Vol 11 (1) ◽  
pp. 107
Author(s):  
B. Simões ◽  
P. R. da Silva ◽  
R. V. Silva ◽  
Y. Avila ◽  
J. A. Forero
Keyword(s):  
Fly Ash ◽  
Municipal Solid Waste ◽  
Solid Waste ◽  
Bottom Ash ◽  
Chloride Diffusion ◽  
Waste Incinerator ◽  
Chloride Diffusion Coefficient ◽  
Municipal Solid Waste Incinerator ◽  
Self Compacting Concrete ◽  
Solid Waste Incinerator

This study aims to evaluate the potential of incorporating fly ash (FA) and municipal solid waste incinerator bottom ash (MIBA) as a partial substitute of cement in the production of self-compacting concrete mixes through an experimental campaign in which four replacement levels (i.e., 10% FA + 20% MIBA, 20% FA + 10% MIBA, 20% FA + 40% MIBA and 40% FA + 20% MIBA, apart from the reference concrete) were considered. Compressive and tensile strengths, Young’s modulus, ultra-sonic pulse velocity, shrinkage, water absorption by immersion, chloride diffusion coefficient and electrical resistivity were evaluated for all concrete mixes. The results showed a considerable decline in both mechanical and durability-related performances of self-compacting concrete with 60% of substitution by MIBA mainly due to the aluminium corrosion chemical reaction. However, workability properties were not significantly affected, exhibiting values similar to those of the control mix.

scholarly journals Reactivity of Ground Coal Bottom Ash to Be Used in Portland Cement

J ◽  
2021 ◽  
Vol 4 (3) ◽  
pp. 223-232
Author(s):  
Esperanza Menéndez ◽  
Cristina Argiz ◽  
Miguel Ángel Sanjuán
Keyword(s):  
Fly Ash ◽  
Coal Fly Ash ◽  
Bottom Ash ◽  
Blended Cement ◽  
Coal Ash ◽  
Pozzolanic Reaction ◽  
Natural Sand ◽  
Coal Bottom Ash ◽  
Novel Material ◽  
Pozzolanic Properties

Ground coal bottom ash is considered a novel material when used in common cement production as a blended cement. This new application must be evaluated by means of the study of its pozzolanic properties. Coal bottom ash, in some countries, is being used as a replacement for natural sand, but in some others, it is disposed of in a landfill, leading thus to environmental problems. The pozzolanic properties of ground coal bottom ash and coal fly ash cements were investigated in order to assess their pozzolanic performance. Proportions of coal fly ash and ground coal bottom ash in the mixes were 100:0, 90:10, 80:20, 50:50, 0:100. Next, multicomponent cements were formulated using 10%, 25% or 35% of ashes. In general, the pozzolanic performance of the ground coal bottom ash is quite similar to that of the coal fly ash. As expected, the pozzolanic reaction of both of them proceeds slowly at early ages, but the reaction rate increases over time. Ground coal bottom ash is a promising novel material with pozzolanic properties which are comparable to that of coal fly ashes. Then, coal bottom ash subjected to an adequate mechanical grinding is suitable to be used to produce common coal-ash cements.

Assessment on Biogas Utilizations in Rural Areas in Urumqi, Xinjiang

2012 ◽  
Vol 512-515 ◽  
pp. 343-346
Author(s):  
Xiao Li Ma ◽  
I Shin Chang ◽  
Jing Wu
Keyword(s):  
Rural Areas ◽  
Alternative Energy ◽  
Practical Experience ◽  
Biomass Energy ◽  
Development Mode ◽  
Ecological Benefits ◽  
Engineering Construction ◽  
Comprehensive Utilization ◽  
Existing Problems ◽  
Reliable Source

As the effective and efficient means of resources utilization, biomass energy has become a very valuable and reliable source of alternative energy in China, especially for remote areas and countryside. First, in order to facilitate the development of biogas applications and promote the economic, social and ecological benefits from comprehensive utilization of biogas in rural areas in Urumqi (Capital of Xinjiang Uygur Autonomous Region, XUAR), the biogas potential was estimated, the biogas engineering construction and biogas comprehensive utilization were evaluated, and the existing problems of biogas development were analyzed, in this study. Second, countermeasures and recommendations were proposed in trying to resolved existing problems, based on international practical experience. And, according to local climatic situation and regional characteristics in Urumqi, ecological agriculture was proposed in this study as the development mode for the rural areas in Urumqi, based on the development of biogas technologies and international practical experience.

Microstructure and Mechanical Properties of Ambiently-Cured Blended Coal Ash-Based Geopolymer Concrete

2016 ◽  
Vol 857 ◽  
pp. 400-404
Author(s):  
Tian Yu Xie ◽  
Togay Ozbakkaloglu
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Bottom Ash ◽  
Coal Ash ◽  
Geopolymer Concrete ◽  
Mass Ratio ◽  
Blended Coal ◽  
Microstructure And Mechanical Properties

This paper presents the results of an experimental study on the behavior of fly ash-, bottom ash-, and blended fly and bottom ash-based geopolymer concrete (GPC) cured at ambient temperature. Four bathes of GPC were manufactured to investigate the influence of the fly ash-to-bottom ash mass ratio on the microstructure, compressive strength and elastic modulus of GPC. All the results indicate that the mass ratio of fly ash-to-bottom ash significantly affects the microstructure and mechanical properties of GPCs

Sign in / Sign up

Export Citation Format

Share Document