scholarly journals CONSOLIDATION ZONES FEATURES FORMATION OF A GROUND AROUND SQUARE SHAPED PILES

2018 ◽  
Vol 1 (50) ◽  
pp. 167-173
Author(s):  
O. V. Malyshev
Keyword(s):  
Experimental Data ◽  
Cross Section ◽  
Analytical Method ◽  
Lateral Surface ◽  
Analytical Methods ◽  
Rational Design ◽  
Initial State ◽  
Compaction Zone ◽  
Analytical Expressions ◽  
Efficiency And Reliability

Necessity to resolve the problem of concerning the analytical dimensions definition and constructing forms of compacted zones of ground around the lateral surface of square cross section pile in normal to pile axis direction are shown in this article. Various analytical methods of ground compacted zones radius determination around cylindrical elements driven into the ground considering its initial state were analyzed. Graph-analytical method of ground compaction zones construction around square cross-section piles was developed. Efficiency of the developed methodology and analytical expressions using possibility to determine the radius of compaction zone of a ground around the driven or jacked-in elements is confirmed by comparing obtained solutions with the experimental data. The developed methodology allows increasing the efficiency and reliability of piles and pile foundations use due to their rational design.

An Analytical Method of Analyzing the Heat Conduction for the Unequal Cross-Section Straight Fin

2013 ◽  
Vol 365-366 ◽  
pp. 1211-1216
Author(s):  
Fan Zhang ◽  
Peng Yun Song
Keyword(s):  
Heat Conduction ◽  
Cross Section ◽  
Analytical Method ◽  
Thermal Analyses ◽  
Cross Sectional ◽  
Cross Section Area ◽  
Section Area ◽  
Calculation Results ◽  
The Cross ◽  
Analytical Expressions

The cross-section area of straight fin is often considered to be equal in the thermal analyses of straight fin, but sometimes it is unequalin actual situation. Taking a straight fin with two unequal cross-sectional areas as an example,an analytical method of heat conduction for unequal section straight fin is presented. The analytical expressions of temperature field and heat dissipating capacity about the fin,which has a smaller cross-section area near the fin base and a larger one, is obtained respectively. The calculation results of the unequal cross-section are fully consistent with the equal area one, so the method is proved right. The results show that the larger the cross section areanear the base,the better is the heat transfer, and the temperature at the base with larger cross-section area is lower than that with smaller cross-section area when the amount of heat is fixed.

scholarly journals Thermochemical properties of liquid alloys along xCu/xSb= 0.2/08 section of the ternary Cu-Sb-Ce system

2017 ◽  
Vol 5 (2) ◽  
pp. 24-29 ◽  
Author(s):  
Natalia Kotova ◽  
Michael Ivanov ◽  
Natalia Usenko
Keyword(s):  
Experimental Data ◽  
High Temperature ◽  
Cross Section ◽  
Analytical Method ◽  
Composition Dependence ◽  
Liquid Alloys ◽  
Thermochemical Properties ◽  
Enthalpies Of Mixing ◽  
The Cross ◽  
Toop Model

The enthalpies of mixing of liquid alloys of the ternary Cu–Sb–Ce system were studied by high-temperature calorimetry along the cross-section = 0.2/0.8. The composition dependence of these values were modelled using four "geometric" models and also the analytical method of Redlich–Kister–Muggianu. A comparison of the experimental data for the cross section = 0.2/0.8 and simulated values of the enthalpies of mixing showed that the most suitable for describing the properties of liquid alloys of ternary Cu–Sb–Ce system is the Toop model.

scholarly journals Analytical Evaluation of the Hadron Number in Extensive Air Showers for Rising Inelasticity

1984 ◽  
Vol 39 (12) ◽  
pp. 1172-1174 ◽  
Author(s):  
Jiben Sidhanta ◽  
Rajkumar Roychoudhury
Keyword(s):  
Experimental Data ◽  
Energy Range ◽  
Cross Section ◽  
Excellent Agreement ◽  
Analytical Method ◽  
Numerical Solutions ◽  
High Energy ◽  
Analytical Evaluation ◽  
Air Showers ◽  
Air Shower

A purely analytical method is presented in this paper for evaluating the average number of hadrons (in an air shower) with a given energy as the inelasticity of the cross-section rises. Our result is found to be in excellent agreement with numerical solutions and also with experimental data, particularly in the high energy range.

Fusion and Breakup Reactions of 17S + 208Pb and 15C + 232ThHalo Nuclei Systems

2015 ◽  
Vol 11 (2) ◽  
pp. 2972-2978
Author(s):  
Fouad A. Majeed ◽  
Yousif A. Abdul-Hussien
Keyword(s):  
Experimental Data ◽  
Cross Section ◽  
Fusion Reaction ◽  
Fusion Cross Section ◽  
Reaction Cross ◽  
Recent Experimental Data ◽  
Barrier Distribution ◽  
Coupled Channel ◽  
Total Fusion ◽  
Full Quantum

In this study the calculations of the total fusion reaction cross section have been performed for fusion reaction systems 17F + 208Pb and 15C + 232Th which involving halo nuclei by using a semiclassical approach.The semiclassical treatment is comprising the WKB approximation to describe the relative motion between target and projectile nuclei, and Continuum Discretized Coupled Channel (CDCC) method to describe the intrinsic motion for both target and projectile nuclei. For the same of comparsion a full quantum mechanical clacualtions have been preforemd using the (CCFULL) code. Our theorticalrestuls are compared with the full quantum mechaincialcalcuations and with the recent experimental data for the total fusion reaction  checking the stability of the distancesThe coupled channel calculations of the total fusion cross section σfus, and the fusion barrier distribution Dfus. The comparsion with experiment proves that the semiclassiacl approach adopted in the present work reproduce the experimental data better that the full quantal mechanical calcautions. 

SETTING A DIAGRAM APPROACH TO CALCULATING VIBRATED, CENTRIFUGED AND VIBROCENTRIFUGED REINFORCED CONCRETE COLUMNS WITH A VARIATROPIC STRUCTURE

2020 ◽  
pp. 22-34
Author(s):  
Л. Р. Маилян ◽  
С. А. Стельмах ◽  
Е. М. Щербань ◽  
М. П. Нажуев
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Cross Section ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
The Cross ◽  
Concrete Elements ◽  
Diagram Approach

Состояние проблемы. Железобетонные элементы изготавливаются, как правило, по трем основным технологиям - вибрированием, центрифугированием и виброцентрифугированием. Однако все основные расчетные зависимости для определения их несущей способности выведены, исходя из основного постулата - постоянства и равенства характеристик бетона по сечению, что реализуется лишь в вибрированных колоннах. Результаты. В рамках диаграммного подхода предложены итерационный, приближенный и упрощенный способы расчета несущей способности железобетонных вибрированных, центрифугированных и виброцентрифугированных колонн. Выводы. Расчет по диаграммному подходу показал существенно более подходящую сходимость с опытными данными, чем расчет по методике норм, а также дал лучшие результаты при использовании дифференциальных характеристик бетона, чем при использовании интегральных и, тем более, нормативных характеристик бетона. Statement of the problem. Reinforced concrete elements are typically manufactured according to three basic technologies - vibration, centrifugation and vibrocentrifugation. However, all the basic calculated dependencies for determining their bearing capacity were derived using the main postulate, i.e., the constancy and equality of the characteristics of concrete over the cross section, which is implemented only in vibrated columns. Results. Within the framework of the diagrammatic approach, iterative, approximate and simplified methods of calculating the bearing capacity of reinforced concrete vibrated, centrifuged and vibrocentrifuged columns are proposed. Conclusions. The calculation according to the diagrammatic approach showed a significantly better convergence with the experimental data than that using the method of norms, and also performs better when using differential characteristics of concrete than when employing integral and particularly standard characteristics of concrete.

scholarly journals Spin-one dark matter and gamma ray signals from the galactic center

2020 ◽  
Vol 2020 (8) ◽  
Author(s):  
H. Hernández-Arellano ◽  
M. Napsuciale ◽  
S. Rodríguez
Keyword(s):  
Dark Matter ◽  
Cross Section ◽  
Gamma Ray ◽  
Galactic Center ◽  
Photon Emission ◽  
Scalar Coupling ◽  
Initial State ◽  
Internal Bremsstrahlung ◽  
Resonance Effects ◽  
State Radiation

Abstract In this work we study the possibility that the gamma ray excess (GRE) at the Milky Way galactic center come from the annihilation of dark matter with a (1, 0) ⊕ (0, 1) space-time structure (spin-one dark matter, SODM). We calculate the production of prompt photons from initial state radiation, internal bremsstrahlung, final state radiation including the emission from the decay products of the μ, τ or hadronization of quarks. Next we study the delayed photon emission from the inverse Compton scattering (ICS) of electrons (produced directly or in the prompt decay of μ, τ leptons or in the hadronization of quarks produced in the annihilation of SODM) with the cosmic microwave background or starlight. All these mechanisms yield significant contributions only for Higgs resonant exchange, i.e. for M ≈ MH /2, and the results depend on the Higgs scalar coupling to SODM, gs. The dominant mechanism at the GRE bump is the prompt photon production in the hadronization of b quarks produced in $$ \overline{D}D\to \overline{b}b $$ D ¯ D → b ¯ b , whereas the delayed photon emission from the ICS of electrons coming from the hadronization of b quarks produced in the same reaction dominates at low energies (ω < 0.3 GeV ) and prompt photons from c and τ , as well as from internal bremsstrahlung, yield competitive contributions at the end point of the spectrum (ω ≥ 30 GeV ). Taking into account all these contributions, our results for photons produced in the annihilation of SODM are in good agreement with the GRE data for gs ∈ [0.98, 1.01] × 10−3 and M ∈ [62.470, 62.505] GeV . We study the consistency of the corresponding results for the dark matter relic density, the spin-independent dark matter-nucleon cross-section σp and the cross section for the annihilation of dark matter into $$ \overline{b}b $$ b ¯ b , τ+τ−, μ+μ− and γγ, taking into account the Higgs resonance effects, finding consistent results in all cases.

scholarly journals Analytical solution for torsion of cylindrical orthotropic annular wedge-shaped bars reinforced by thin shells

2021 ◽  
Author(s):  
István Ecsedi ◽  
Attila Baksa
Keyword(s):  
Analytical Solution ◽  
Cross Section ◽  
Analytical Method ◽  
Torsional Rigidity ◽  
Circular Ring ◽  
Thin Shells ◽  
Elastic Wedge ◽  
Curved Boundary ◽  
Cylindrically Orthotropic ◽  
Boundary Surfaces

AbstractThis paper deals with the Saint-Venant torsion of elastic, cylindrically orthotropic bar whose cross section is a sector of a circular ring shaped bar. The cylindrically orthotropic homogeneous elastic wedge-shaped bar strengthened by on its curved boundary surfaces by thin isotropic elastic shells. An analytical method is presented to obtain the Prandtl’s stress function, torsion function, torsional rigidity and shearing stresses. A numerical example illustrates the application of the developed analytical method.

scholarly journals Total cross sections of eγ → $$ eX\overline{X} $$ processes with X = μ, γ, e via multiloop methods

2021 ◽  
Vol 2021 (1) ◽  
Author(s):  
Roman N. Lee ◽  
Alexey A. Lyubyakin ◽  
Vyacheslav A. Stotsky
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Elliptic Integral ◽  
High Energy ◽  
Calculation Methods ◽  
Complete Elliptic Integral ◽  
Total Cross Sections ◽  
Multiloop Calculation ◽  
The Cross ◽  
Analytical Expressions

Abstract Using modern multiloop calculation methods, we derive the analytical expressions for the total cross sections of the processes e−γ →$$ {e}^{-}X\overline{X} $$ e − X X ¯ with X = μ, γ or e at arbitrary energies. For the first two processes our results are expressed via classical polylogarithms. The cross section of e−γ → e−e−e+ is represented as a one-fold integral of complete elliptic integral K and logarithms. Using our results, we calculate the threshold and high-energy asymptotics and compare them with available results.

An investigation of effects of level density models and gamma ray strength functions on cross-section calculations for the production of 90Y, 153Sm, 169Er, 177Lu and 186Re therapeutic radioisotopes via (n,γ) reactions

2019 ◽  
Vol 108 (1) ◽  
pp. 11-17
Author(s):  
Mert Şekerci ◽  
Hasan Özdoğan ◽  
Abdullah Kaplan
Keyword(s):  
Experimental Data ◽  
Cross Section ◽  
Production Cross Section ◽  
Gamma Ray ◽  
Production Cross ◽  
Level Density ◽  
Experimental Studies ◽  
Level Density Models ◽  
Strength Functions ◽  
Cancer Diseases

Abstract One of the methods used to treat different cancer diseases is the employment of therapeutic radioisotopes. Therefore, many clinical, theoretical and experimental studies are being carried out on those radioisotopes. In this study, the effects of level density models and gamma ray strength functions on the theoretical production cross-section calculations for the therapeutic radioisotopes 90Y, 153Sm, 169Er, 177Lu and 186Re in the (n,γ) route have been investigated. TALYS 1.9 code has been used by employing different level density models and gamma ray strength functions. The theoretically obtained data were compared with the experimental data taken from the literature. The results are presented graphically for better interpretation.

Sign in / Sign up

Export Citation Format

Share Document