scholarly journals Numerical and Experimental Research on Convergence Angle of Wet Sprayer Nozzle

2018 ◽  
Vol 4 (9) ◽  
pp. 1985 ◽  
Author(s):  
Chang Su ◽  
Yun-hai Cheng
Keyword(s):  
Numerical Simulation ◽  
Theoretical Analysis ◽  
Flow Field ◽  
Distribution System ◽  
Volume Fraction ◽  
Internal Flow ◽  
Outlet Section ◽  
Validity And Reliability ◽  
Phase Volume Fraction ◽  
Nozzle Structure

Shotcrete is a popular support method in construction of both ground projects and underground projects, such as tunnels, subways, slopes and roadway, etc. However, at present researches on the influence of nozzle structure parameters on the performance of concrete injection are insufficient. This research focuses on the influence of various parameters of nozzle structure on the evenness and dust generating, and conducts a systematic study on the flow characteristics of the concrete in the nozzle of wet spraying machinery and the quality control law, through a comprehensive research method combining theoretical analysis, numerical simulation and field tests. On the basis of dynamic analysis of the internal flow field of the nozzle, the mathematical model and numerical model of the internal flow field of the nozzle are establishes. Then the simulation calculation of the flow field of the wet spray nozzle is conducted with the FLUENT® software. The fluid’s contour about velocity and phase volume fraction in the nozzle were obtained. On this basis this paper analyzed each phase’s volume fraction of the mixed fluid in the outlet section. The convergent section of the nozzle is tested in the spray concrete impact force distribution system. The results are in good correspondence with the results of theoretical analysis and numerical simulation, which verifies the validity and reliability of the conclusion of numerical simulation. This paper provides the basis for the optimization of nozzle structure, and the improvement of the sprayed concrete construction quality.

scholarly journals Numerical Simulation and Experimental Study on Flow Field in a Swirl Nozzle

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Yicheng Sun ◽  
Yufan Fu ◽  
Baohui Chen ◽  
Jiaxing Lu ◽  
Wanquan Deng
Keyword(s):  
Flow Field ◽  
Velocity Distribution ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Low Pressure ◽  
External Flow ◽  
Droplet Velocity ◽  
Inlet Pressure ◽  
Outlet Section ◽  
Local Pressure

In order to study the internal flow characteristics and external droplet velocity distribution characteristics of the swirl nozzle, the following methods were used: numerical simulations were used to study the internal flow characteristics of a swirl nozzle and phase Doppler particle velocimetry was used to determine the corresponding external droplet velocity distribution under medium and low pressure conditions. The distributions of pressure and water velocity inside the nozzle were obtained. Meanwhile, the velocities of droplets outside the nozzle in different sections were discussed. The results show that the flow rate in the swirl nozzle increases with the increase in inlet pressure, and the local pressure in the region decreases because of the excessive velocity at the internal outlet section of the swirl nozzle, resulting in cavitation. The experimental results show that under an external flow field, the minimum droplet velocity occurs in the axial direction; starting from the axis, the velocity first increases and then decreases along the radial direction. Swirling motion inside the nozzle and velocity variations in the external flow field occur under medium and low pressure conditions. The relationship between the inlet pressure and the distributions of water droplets’ velocities was established, which provides a reference for the research and development of the swirl nozzle.

Numerical Simulation of Double Inlet Cylinder Cyclone Using CFD

2013 ◽  
Vol 275-277 ◽  
pp. 558-561
Author(s):  
Xiao Ming Yuan ◽  
Hui Jun Zhao ◽  
Jing Yi Qu
Keyword(s):  
Flow Field ◽  
Volume Fraction ◽  
Separation Efficiency ◽  
Separation Performance ◽  
Two Phase ◽  
Phase Volume Fraction ◽  
Fluid Field ◽  
Cylindrical Cyclone ◽  
Discrete Phase ◽  
New Type

Designed a new type of double inlet cylindrical cyclone. For search the separation performance in a cylindrical cyclone. By use of CFD，applied the RSM turbulence model and Euler two-phase flow method and ASM which to simulate separation process and flow field within a double inlet cylindrical cyclone. Then compared with the single inlet cyclone，obtained velocity distribution. Analyzed the differences of discrete phase volume fraction between different viscosity. The results show that the new-style cyclone caught more stable fluid field and higher separation efficiency. And when the viscosity is about 0.75 kg/m•s， the separation efficiency and stability of the oil core is higher. Preliminary flow field law is shown up.

Numerical simulation of three-dimensional airflow in a novel dual-feed rotor spinning box

2016 ◽  
Vol 88 (3) ◽  
pp. 237-253 ◽  
Author(s):  
Nicholus Tayari Akankwasa ◽  
Huiting Lin ◽  
Yuze Zhang ◽  
Jun Wang
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Three Dimensional ◽  
Internal Flow ◽  
Velocity Variation ◽  
Positive Pressure ◽  
Three Dimensional Model ◽  
Air Velocity ◽  
Rotor Spinning ◽  
Pressure Profiles

In order to regulate turbulence strength and determine airflow characteristics in a new dual-feed rotor spinning unit, the internal flow field is investigated. A computational fluid dynamics technique is employed to numerically study the three-dimensional model of the internal airflow in the new design. The effects of air velocity variation on turbulence strength, negative pressure, Re, and wall pressure distribution are investigated based on simulation data and previous studies. The results show that the turbulence strength and Re increased with increase in inlet air velocity. Pressure profiles inside the rotor varied significantly with positive pressure observed at the channel exits. Minimal inlet velocity maintains the flow field in the rotor interior below 100 m/s, which gives the ideal turbulence required to minimize yarn quality deterioration. The dual-feed rotor spinning unit showed more orderly streamline patterns with fewer vortices compared to the conventional one. The numerical simulation can provide insights on airflow studies and some guidelines for future prototyping and experiments to further improve the new design.

Numerical Simulation of Interior Flow Field of Reactor Coolant Pump under Station Blackout Accident

2012 ◽  
Vol 455-456 ◽  
pp. 1002-1008 ◽  
Author(s):  
Yi Ming Xu ◽  
Shi Ming Xu
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Internal Flow ◽  
Simulation Method ◽  
Governing Equations ◽  
Coolant Pump ◽  
Reactor Coolant ◽  
Internal Characteristic ◽  
Station Blackout ◽  
Interior Flow

Numerical simulation is used for researching the transient characteristic and internal characteristic of the reactor coolant pump under station blackout accident. The simulation method has been presented by analyzing difference scheme for governing equations. The analytical model of reactor coolant pump flow field has been established by analyzing adequately the influence of varying rotation speed to the pump external characteristic. Finally, the pump internal flow characteristic is exposed.

Numerical simulation of the internal flow field of a new main nozzle in an air-jet loom based on Fluent

2015 ◽  
Vol 85 (15) ◽  
pp. 1590-1601 ◽  
Author(s):  
Liang Chen ◽  
Zhi-hua Feng ◽  
Teng-zhong Dong ◽  
Wei-hua Wang ◽  
Shuai Liu
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Internal Flow ◽  
Air Jet ◽  
Air Jet Loom

scholarly journals Numerical Investigation of Flow Field and Energy Loss in a Centrifugal Pump as Turbine

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Jingze Li ◽  
Dongrong Meng ◽  
Xun Qiao
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Energy Loss ◽  
Entropy Generation ◽  
Flow Separation ◽  
Guide Vane ◽  
Great Influence ◽  
Internal Flow ◽  
Asymmetric Structure ◽  
Centrifugal Pumps

Centrifugal pumps as turbine (PAT) are widely used in petrochemical and water conservancy industries. The research on the internal flow field and energy loss of PAT is of great significance to improve the performance and efficiency of PAT. In this paper, experimental and numerical simulation methods are used to study the energy loss and flow field. The results show that the numerical simulation method can accurately simulate the internal flow field of PAT. And the entropy generation theory is applied to visualize the internal energy loss of PAT through the comparison of total pressure loss and entropy generation. The highest energy loss among PAT components is the guide vane. The loss in the guide vane is mainly caused by the flow separation caused by the wake of the guide vane and the asymmetric structure of the volute. The losses in the impeller are mainly due to flow separation and wake. Besides, the unsteady simulation results show that rotor-stator interaction has a great influence on the gap between the impeller and the guide vane. The research results provide a reference for the design of the PAT. This study is beneficial to studying the dynamic and static interference and PAT vibration to improve the stability of the PAT.

Sign in / Sign up

Export Citation Format

Share Document