scholarly journals THE ANALYSIS OF DYNAMIC RESPONSE AND VOLTAGE FLICKER WITH STATCOM ON DISTRIBUTION NETWORK

2020 ◽  
Vol 4 (4) ◽  
pp. 27-33
Author(s):  
V.Siva Brahmaiah ◽  
Manav Adhikari
Keyword(s):  
Dynamic Response ◽  
Power Systems ◽  
Distribution System ◽  
Power Flow ◽  
Reactive Power ◽  
Distribution Network ◽  
Alternating Current ◽  
Pwm Inverter ◽  
Voltage Flicker ◽  
Flexible Alternating Current Transmission

The Flexible Alternating Current Transmission Systems (FACTS) device deals with the control of power flow, alternating current of transmission line and immediately respond towards the stability problems of the system. The present paper show that how the FACTS device STATCOM enhance the dynamic response and voltage flicker in distribution network of the power systems. In MATLAB a simplified distribution system is modeled and the find out the desired objectives. D-STATCOM changes from inductive to capacitive operation, the modulation index of the PWM inverter is increased from 0.56 to 0.9 which corresponds to a proportional increase in inverter voltage. Reversing of reactive power is very fast, about one cycle, as observed on D-STATCOM current. Observed on Scope that voltage fluctuation at bus B3 is now reduced to +/- 0.7 %. The D-STATCOM compensates voltage by injecting a reactive current modulated and varying between 0.6 pu capacitive when voltage is low and 0.6 pu inductive when voltage is high.

scholarly journals Reactive Power Management Considering Stochastic Optimization under the Portuguese Reactive Power Policy Applied to DER in Distribution Networks

Energies ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 4028 ◽  
Author(s):  
Abreu ◽  
Soares ◽  
Carvalho ◽  
Morais ◽  
Simão ◽  
...  
Keyword(s):  
Power Management ◽  
Distribution System ◽  
Power Flow ◽  
Optimal Power Flow ◽  
Reactive Power ◽  
Renewable Energy Sources ◽  
Distribution Network ◽  
Real Data ◽  
Distribution Networks ◽  
System Operator

Challenges in the coordination between the transmission system operator (TSO) and the distribution system operator (DSO) have risen continuously with the integration of distributed energy resources (DER). These technologies have the possibility to provide reactive power support for system operators. Considering the Portuguese reactive power policy as an example of the regulatory framework, this paper proposes a methodology for proactive reactive power management of the DSO using the renewable energy sources (RES) considering forecast uncertainty available in the distribution system. The proposed method applies a stochastic sequential alternative current (AC)-optimal power flow (SOPF) that returns trustworthy solutions for the DSO and optimizes the use of reactive power between the DSO and DER. The method is validated using a 37-bus distribution network considering real data. Results proved that the method improves the reactive power management by taking advantage of the full capabilities of the DER and by reducing the injection of reactive power by the TSO in the distribution network and, therefore, reducing losses.

Research and Application of SVC Technology in Grid

2014 ◽  
Vol 543-547 ◽  
pp. 878-883
Author(s):  
Jun Dong ◽  
Jian Guo Xu ◽  
Hao Zhang ◽  
Yu Jie Pei ◽  
Xian Feng Li
Keyword(s):  
Power Systems ◽  
Power Quality ◽  
Distribution System ◽  
Power Flow ◽  
Reactive Power ◽  
Control Strategies ◽  
Load Capacity ◽  
Flow Distribution ◽  
Nonlinear Load ◽  
The Impact

The cause serious deterioration in power quality problems for the growing impact and nonlinear load capacity, introduced SVC device in the role of modern power systems and applications. According to the lack of adequate regional dynamic reactive power regulation means to cause voltage fluctuations, harmonics exceeded the actual situation, through analysis and simulation of the existing 66kV grid power quality conditions, refers to the necessity of application of SVC, the compensation capacity for SVC, filter capacitor system parameters and control strategies were designed, the results show improved 220kV SVC reactive power flow distribution system, reducing the system once or twice a net loss, reducing the impact and harmonic interference voltage caused by nonlinear loads, system security, economic operation of great significance.

scholarly journals THE COMPARATIVE STUDY OF STATCOM WITH FC-TCR AND SSSC

2020 ◽  
Vol 2 (3) ◽  
pp. 1-8
Author(s):  
Manav Adhikari
Keyword(s):  
Power Systems ◽  
Power Flow ◽  
Alternating Current ◽  
Transmission System ◽  
System Stability ◽  
Voltage Profile ◽  
Static Synchronous Compensator ◽  
Line System ◽  
Flexible Alternating Current Transmission ◽  
The Stability

The Flexible Alternating Current Transmission Systems (FACTS) device deals with the control of power flow, alternating current of transmission line and immediately respond towards the stability problems of the system. The present paper show that how the FACTS devices enhance the different parameter of the power systems like power transfer capacity of line, system stability etc. In MATLAB a simplified transmission system is modeled and the resultant power (PQ) and voltage profiles are studied as an uncompensated system. Now the same transmission system is simulating with FACTS device i.e. Static Synchronous Series Compensator (SSSC), Fixed Capacitor Thyristor Controlled Reactor (FC-TCR) and Static Synchronous Compensator (STATCOM). The result obtained after simulation provide the power and voltage profiles, are analyzed as a compensated system. Finally we found that a compensated system have better voltage profile and power flow w.r.t. an uncompensated system.

scholarly journals Loss Minimization in Distribution Network using Wind Power Plant Reactive Power Support

2021 ◽  
Author(s):  
Aeishwarya Baviskar ◽  
Kaushik Das ◽  
Anca Daniela Hansen ◽  
Panos Menegatos
Keyword(s):  
Wind Power ◽  
Distribution System ◽  
Power Flow ◽  
Power Plants ◽  
Reactive Power ◽  
Distribution Network ◽  
Distribution Networks ◽  
Voltage Profile ◽  
Network Losses ◽  
Optimization Methodology

<div>The increased penetration of wind power plants (WPPs) in distribution networks challenges the distribution system operators (DSOs) to improve and optimize networks’ operation. A higher amount of local power production translates to more losses in the network. This paper proposes a deterministic optimization methodology to minimize the losses in distribution networks with WPPs, by exploiting WPPs’ capability to control reactive power in coordination with the on-load tap changers from the MV/HV transformer, avoiding the need for network reinforcements. The principal objective is to optimize the reactive power flow in the network. Measurements from a real distribution network with a large share of controllable WPPs under varying wind and load conditions are used for the study. The benefits and the challenges of the optimization methodology are assessed and discussed with respect to active power losses, voltage profile and reactive power. The results show that with reactive power support from WPPs, network losses are reduced by 4.2 %. Higher loss reductions (up to 19 %) can be achieved through a coordinated action between the WPPs and TSO. Furthermore, it is shown that the distribution network can act as an asset to the transmission network for reactive power support, via actively controlling WPP’s reactive power.</div>

scholarly journals Loss Minimization in Distribution Network using Wind Power Plant Reactive Power Support

2021 ◽  
Author(s):  
Aeishwarya Baviskar ◽  
Kaushik Das ◽  
Anca Daniela Hansen ◽  
Panos Menegatos
Keyword(s):  
Wind Power ◽  
Distribution System ◽  
Power Flow ◽  
Power Plants ◽  
Reactive Power ◽  
Distribution Network ◽  
Distribution Networks ◽  
Voltage Profile ◽  
Network Losses ◽  
Optimization Methodology

<div>The increased penetration of wind power plants (WPPs) in distribution networks challenges the distribution system operators (DSOs) to improve and optimize networks’ operation. A higher amount of local power production translates to more losses in the network. This paper proposes a deterministic optimization methodology to minimize the losses in distribution networks with WPPs, by exploiting WPPs’ capability to control reactive power in coordination with the on-load tap changers from the MV/HV transformer, avoiding the need for network reinforcements. The principal objective is to optimize the reactive power flow in the network. Measurements from a real distribution network with a large share of controllable WPPs under varying wind and load conditions are used for the study. The benefits and the challenges of the optimization methodology are assessed and discussed with respect to active power losses, voltage profile and reactive power. The results show that with reactive power support from WPPs, network losses are reduced by 4.2 %. Higher loss reductions (up to 19 %) can be achieved through a coordinated action between the WPPs and TSO. Furthermore, it is shown that the distribution network can act as an asset to the transmission network for reactive power support, via actively controlling WPP’s reactive power.</div>

scholarly journals Distribution system power quality compensation using a HSeAPF based on SRF and SMC features

2021 ◽  
Author(s):  
Akram Qashou ◽  
Sufian Yousef ◽  
Abdallah A. Smadi ◽  
Amani A. AlOmari
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Reactive Power ◽  
Sliding Mode ◽  
Distribution Network ◽  
Harmonic Distortion ◽  
Phase Locked Loop ◽  
Voltage Source ◽  
Voltage Source Converter ◽  
Non Linear

AbstractThe purpose of this paper is to describe the design of a Hybrid Series Active Power Filter (HSeAPF) system to improve the quality of power on three-phase power distribution grids. The system controls are comprise of Pulse Width Modulation (PWM) based on the Synchronous Reference Frame (SRF) theory, and supported by Phase Locked Loop (PLL) for generating the switching pulses to control a Voltage Source Converter (VSC). The DC link voltage is controlled by Non-Linear Sliding Mode Control (SMC) for faster response and to ensure that it is maintained at a constant value. When this voltage is compared with Proportional Integral (PI), then the improvements made can be shown. The function of HSeAPF control is to eliminate voltage fluctuations, voltage swell/sag, and prevent voltage/current harmonics are produced by both non-linear loads and small inverters connected to the distribution network. A digital Phase Locked Loop that generates frequencies and an oscillating phase-locked output signal controls the voltage. The results from the simulation indicate that the HSeAPF can effectively suppress the dynamic and harmonic reactive power compensation system. Also, the distribution network has a low Total Harmonic Distortion (< 5%), demonstrating that the designed system is efficient, which is an essential requirement when it comes to the IEEE-519 and IEC 61,000–3-6 standards.

scholarly journals Mitigation of Voltage Dip and Voltage Flickering by Multilevel D-STATCOM

2012 ◽  
Vol 2012 ◽  
pp. 1-11 ◽  
Author(s):  
M. S. Ballal ◽  
H. M. Suryawanshi ◽  
T. Venkateswara Reddy
Keyword(s):  
Power Quality ◽  
Distribution System ◽  
Reactive Power ◽  
Distribution Network ◽  
Voltage Sag ◽  
Service Interruptions ◽  
Flexible Ac Transmission ◽  
Voltage Dip ◽  
Basic Power ◽  
Ac Transmission

The basic power quality problems in the distribution network are voltage sag (dip), voltage flickering, and the service interruptions. STATCOM is a Flexible AC Transmission Systems (FACTS) technology device which can independently control the flow of reactive power. This paper presents the simulation and analysis of a STATCOM for voltage dip and voltage flickering mitigation. Simulations are carried out in MATLAB/Simulink to validate the performance of the STATCOM. A comparison between the six-pulse inverter and the five-level diode-clamped inverter is carried out for the performance of 66/11 KV distribution system.

Optimal Capacitors Placement of Distribution Systems Using 2nd Order Power Loss Sensitivity Analysis and Hierarchical Clustering

2014 ◽  
Vol 986-987 ◽  
pp. 377-382 ◽  
Author(s):  
Hui Min Gao ◽  
Jian Min Zhang ◽  
Chen Xi Wu
Keyword(s):  
Sensitivity Analysis ◽  
Hierarchical Clustering ◽  
Distribution System ◽  
Power Flow ◽  
Distribution Systems ◽  
Reactive Power ◽  
Digital Simulation ◽  
Second Order ◽  
First Order ◽  
The Impact

Heuristic methods by first order sensitivity analysis are often used to determine location of capacitors of distribution power system. The selected nodes by first order sensitivity analysis often have virtual high by first order sensitivities, which could not obtain the optimal results. This paper presents an effective method to optimally determine the location and capacities of capacitors of distribution systems, based on an innovative approach by the second order sensitivity analysis and hierarchical clustering. The approach determines the location by the second order sensitivity analysis. Comparing with the traditional method, the new method considers the nonlinear factor of power flow equation and the impact of the latter selected compensation nodes on the previously selected compensation location. This method is tested on a 28-bus distribution system. Digital simulation results show that the reactive power optimization plan with the proposed method is more economic while maintaining the same level of effectiveness.

scholarly journals Reactive Power Loss & Efficiency Calculation Using Load Flow Technique In Distribution System For Pune City

2012 ◽  
pp. 76-79
Author(s):  
Gaikwad Vikas Subhash ◽  
Swati S. More
Keyword(s):  
Power Systems ◽  
Distribution System ◽  
Power Loss ◽  
Distribution Systems ◽  
Service Sector ◽  
Reactive Power ◽  
Flow Problem ◽  
Load Flow ◽  
Total System ◽  
Loss Efficiency

Reactive power compensation is an important issue in electric power systems, involving operational, economical and quality of service aspects. Consumer loads (residential, industrial, service sector, etc.) impose active and reactive power demand, depending on their characteristics. This paper presents an efficient method for solving the load flow problem in distribution systems and which is implemented for Pune city (India) to check the validity of proposed method. A simple algebraic matrix equation to solve the load flow problem is derived by using the complex power balance equations. By adopting the rectangular coordinate, which requires the neglect of only second order terms in the linearization procedure, the proposed method gives better convergence characteristics. Newton-Raphsonmethod is the famous load flow calculation technique, and normally used dueto its rapidness of numerical convergence. The proposed method estimates the incremental changesof active power on each generation bus with respect to the total system power loss, efficiency and the estimated value are used to update the slack bus power.

scholarly journals Validating Response of AC Microgrid to Line-to-Line Short Circuit in Islanded Mode Using Dynamic Analysis

2019 ◽  
pp. 1-15
Author(s):  
Maruf A. Aminu
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Power Flow ◽  
Reactive Power ◽  
Short Circuit ◽  
Operating Mode ◽  
Superior Performance ◽  
Induction Generators ◽  
Bidirectional Power Flow ◽  
Control Regime

This paper is presented in an attempt to validate the dynamic response of a microgrid to line-to-line short circuit. The microgrid components include two identical Wind Turbine Generators (WTGs) tied to a 100MVA, 13.8kV utility via a Point of Common Coupling (PCC). The utility-microgrid testbed is modeled in SIMPOWERSystems® using two Doubly-Fed Induction Generators (DFIGs) in the microgrid side. While in islanded operating mode, line-to-line short circuit fault is applied at 6.0s and withdrawn at 8.0s, obtaining a 50.0s dynamic response of the system for different fault locations, under voltage and reactive power control regimes of the wind turbine controller. For measurement purpose, the absolute value of the stator complex voltage is transformed to  reference frame. Bidirectional power flow between the two feeders is established in the study. The study also confirms that the microgrid composed of DFIGs offer reactive power management capability, particularly by presenting superior performance when stressed under Q control regime than under V control regime. Finally, the response of the testbed to line-to-line short circuit has been validated and shown to be consistent with established short circuit theory.

Sign in / Sign up

Export Citation Format

Share Document