scholarly journals Household Biomass Gas Stove Performance and Exhaust Gas Emission

2019 ◽  
Vol 3 (1) ◽  
pp. 19-20
Author(s):  
S N Jansri ◽  
M Kumpanalaisatit ◽  
T Sataklang
Keyword(s):  
Exhaust Emission ◽  
Exhaust Gas ◽  
Gas Emission ◽  
Emission Standard ◽  
Test Technique ◽  
Fuel Gas ◽  
Water Boiling Test ◽  
Air Inlet ◽  
Exhaust Gas Emission ◽  
Secondary Air

This work focuses on the design of the household biomass gas stove which is suitable for the lifestyle of the Thai northern people. In addition, the performance and exhaust emission of the stove - updraft gasifier - was design per the community requirement were evaluated. The stove consists of a combustion chamber – a primary chamber - and a secondary chamber with the primary and secondary air inlet of 0.016 and 0.002 m2, respectively. Moreover, the flow rate of primary air and secondary air was 0.456 and 1.340 kg/s, respectively. The performance of the stove was analyzed by the water boiling test technique and the emission of exhaust gas was evaluated with a fuel gas analyzer. The result indicated that the thermal efficiency of the stove was 44.84%. The specific fuel consumption was 0.029 kg/kg of water. Comparing the designed stove with the traditional clay brazier stove, the performance of the designed stove was higher than the traditional stove. The emission comparison between the designed household biomass gas stove, the traditional stove and the Thai exhaust gas emission standard indicated that both stoves released NOx and SO2 which are less than the standard whereas CO emission of the designed stove conformed to the standard. This work confirmed that the efficiency and the exhaust gas emission of the designed stove are better than the traditional stove. Therefore, this household biomass gas stove could replace the conventional stove

scholarly journals Influence of the dilution factor on the uncertainty of the exhaust gas emission results obtained during testing on the chassis dynamometer

2018 ◽  
Vol 19 (6) ◽  
pp. 737-742
Author(s):  
Andrzej Szczotka ◽  
Bartosz Puchałka ◽  
Piotr Bielaczyc ◽  
Borys Adamiak
Keyword(s):  
Large Impact ◽  
Exhaust Emission ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Chassis Dynamometer ◽  
Dilution Factor ◽  
Gas Emission ◽  
Test Vehicle ◽  
Emission Level ◽  
Exhaust Gas Emission

Exhaust emission measurements on the chassis dynamometer are one of the most important and most complex tests which are performed on vehicles powered by combustion engines. The sample and dilution system (CVS - Constant Volume Sampling) belongs to the most important parts of the exhaust emission laboratory, and has a large impact on the accuracy of the results obtained. In this paper, the influence of the dilution factor (i.e. parameter changed by means of the CVS system, depending on the emission level and engine displacement of the test vehicle) on the uncertainty of the exhaust gas emission results is analysed.

ESTIMATION OF EXHAUST SHIP EMISSION FROM MARINE TRAFFIC IN THE STRAITS OF SINGAPORE AND BATAM WATERWAYS USING AUTOMATIC IDENTIFICATION SYSTEM (AIS) DATA

2015 ◽  
Vol 77 (23) ◽  
Author(s):  
Hendra Saputra ◽  
Mufti Fathonah Muvariz ◽  
Sapto Wiratno Satoto ◽  
Jaswar Koto
Keyword(s):  
Exhaust Emission ◽  
Automatic Identification ◽  
Identification System ◽  
Exhaust Gas ◽  
Emission Rates ◽  
Gas Emission ◽  
Automatic Identification System ◽  
Marine Traffic ◽  
Exhaust Gas Emission ◽  
Ship Emission

This study focuses on the Strait of Singapore and Batam Waterways area because it is one of the world’s most congested straits used for international shipping. The study aims to estimate exhaust gas emission and the concentration of emission to several areas around the strait. This is accomplished by evaluating the density of shipping lanes in the strait by using the data which obtained by Automatic Identification System (AIS). MEET methodology is used to estimate emissions from ships. There were 1269 total number of ships through the strait on September 27, 2014 at 06.00 am-08.00 am produces total exhaust emission for NOx, CO, CO2, VOC, PM and SOx were about 12595.35 g/second (15.99%), 25725.19 g/second (32.66%), 11832.31 g/second (15.02%), 5973.23 g/second (7.58%), 443.71 g/second, (0.56%), 22185.57 g/second (28.17%), respectively. The ships under the Singapore flag contribute approximately 22.78% of total emissions in the Strait of Singapore and Batam Waterways followed by Panama, Indonesia and Malaysia 14.47%, 3.67%, 1.91%, respectively. Based on the total emission rates hips under Indonesia and Malaysia rank of seventh and eighth respectively.

scholarly journals Spider Web Shape of Brass Catalytic Converter for Reducing Exhaust Gas Emission

2017 ◽  
Vol 2 (1) ◽  
pp. 41
Author(s):  
Heni Hendaryati ◽  
Ali Mokhtar
Keyword(s):  
Catalytic Converter ◽  
Exhaust System ◽  
Motor Vehicles ◽  
Exhaust Emission ◽  
Exhaust Gas ◽  
Fossil Fuel Combustion ◽  
Gas Emission ◽  
Ic Engine ◽  
Spider Web ◽  
Exhaust Gas Emission

The rapid increase of the number of motor vehicles, especially motorcycles, makes serious problem caused by the pollution from gas emission of fossil fuel combustion. The problems related to human health and the erosion on ozone layer is credited to its gas emission. Several dangerous and toxic gasses such as Hydrocarbon (HC), Carbon Monoxide (CO), and Nitrogen Oxide (NOx), Sulphur Dioxide (SO2), and Lead (Pb) are emitted during IC engine operation.To manage those dangerous gasses, catalytic converter which converts the gasses into more eco-friendly CO2H2O and N2 may be employed. In this research, a specially designed catalytic converter made from brass (CuZn) wire in the form of spider web pattern was fitted into exhaust system of a standard motorcycle. The performance of the converter for several engine rotation speeds was examined by measuring CO and HC of exhaust by using Gas Analyzer.By comparing the exhaust of a standard exhaust system and modified exhaust system (fitted with converter), it can be concluded that the converter was able to decrease the exhaust emission gas. For HC content, the percentage of decrease was as much as 36,88 % for converter fitted exhaust system compared to 61.12% for standard one. For CO content, the decrease percentage was 19.90% compared to 80.10% for standard one.

scholarly journals Plug-in Hybrid Ecological Category in Real Driving Emissions

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2340
Author(s):  
Kinga Skobiej ◽  
Jacek Pielecha
Keyword(s):  
Exhaust Emissions ◽  
Hybrid Vehicles ◽  
Point Of View ◽  
Exhaust Emission ◽  
Exhaust Gas ◽  
Gas Emission ◽  
Emission Standards ◽  
Ecological Aspects ◽  
Exhaust Gas Emission ◽  
Innovative Solution

Transportation, as one of the most growing industries, is problematic due to environmental pollution. A solution to reduce the environmental burden is stricter emission standards and homologation tests that correspond to the actual conditions of vehicle use. Another solution is the widespread introduction of hybrid vehicles—especially the plug-in type. Due to exhaust emission tests in RDE (real driving emissions) tests, it is possible to determine the real ecological aspects of these vehicles. The authors of this paper used RDE testing of the exhaust emissions of plug-in hybrid vehicles and on this basis evaluated various hybrid vehicles from an ecological point of view. An innovative solution proposed by the authors is to define classes of plug-in hybrid vehicles (classes from A to C) due to exhaust emissions. An innovative way is to determine the extreme results of exhaust gas emission within the range of acceptable scatter of the obtained results. By valuating vehicles, it will be possible in the future to determine the guidelines useful in designing more environmentally friendly power units in plug-in hybrid vehicles.

scholarly journals Method of verifying the emission level of the exhaust components of a special vehicle in relation to EURO III standard in road conditions

2021 ◽  
Author(s):  
Jędrzej Matla ◽  
Kaźmierczak Andrzej
Keyword(s):  
Test Object ◽  
Real Life ◽  
Exhaust Emission ◽  
Exhaust Gas ◽  
Emission Standard ◽  
Life Conditions ◽  
Measurement Results ◽  
Special Vehicle ◽  
Testing Mode ◽  
Mode A

The following article presents the method of verification of EURO III standard in real life conditions for special vehicles. The test object qualified as a special vehicle of N3G category was tested in road conditions along a defined route, and then the obtained measurement results were compared to the exhaust emission standard (EURO III) applicable for this vehicle in transient testing mode. A method of comparing the emission factors in road conditions with the indicators obtained on the engine dynamometer was proposed. An AVL mobile exhaust gas analyzers (PEMS) dedicated for the Real Driving Emissions (RDE) road tests were used in the research.

Maintaining Marine Diesel Emissions Using Performance Monitoring

2010 ◽  
Author(s):  
Herbert Roeser ◽  
Dilip Kalyankar
Keyword(s):  
Diesel Engine ◽  
Performance Monitoring ◽  
Fuel Oil ◽  
Exhaust Gas ◽  
Gas Emission ◽  
Heavy Fuel Oil ◽  
Tier Ii ◽  
Technological Advances ◽  
Exhaust Gas Emission ◽  
Marine Diesel

Ships are an integral part of modern commercial transport, leisure travel, and military system. A diesel engine was used for the first time for the propulsion of a ship sometime in the 1910s and has been the choice for propulsion and power generation, ever since. Since the first model used in ship propulsion, the diesel engine has come a long way with several technological advances. A diesel engine has a particularly high thermal efficiency. Added to it, the higher energy density of the diesel fuel compared to gasoline fuel makes it inherently, the most efficient internal combustion engine. The modern diesel engine also has a very unique ability to work with a variety of fuels like diesel, heavy fuel oil, biodiesel, vegetable oils, and several other crude oil distillates which is very important considering the shortage of petroleum fuels that we face today. In spite of being highly efficient and popular and in spite of all the technological advances, the issue of exhaust gas emissions has plagued a diesel engine. This issue has gained a lot of importance since 1990s when IMO, EU, and the EPA came up with the Tier I exhaust gas emission norms for the existing engine in order to reduce the NOx and SOx. Harsher Tier II and Tier III norms were later announced for newer engines. Diesel fuels commonly used in marine engines are a form of residual fuel, also know as Dregs or Heavy Fuel Oil and are essentially the by products of crude oil distillation process used to produce lighter petroleum fuels like marine distillate fuel and gasoline. They are cheaper than marine distillate fuels but are also high in nitrogen, sulfur and ash content. This greatly increases the NOx and SOx in the exhaust gas emission. Ship owners are trapped between the need to use residual fuels, due to cost of the large volume of fuel consumed, in order to keep the operation of their ships to a competitive level on one hand and on the other hand the need to satisfy the stringent pollution norms as established by the pollution control agencies worldwide. Newer marine diesel engines are being designed to meet the Tier II and Tier III norms wherever applicable but the existing diesel engine owners are still operating their engines with the danger of not meeting the applicable pollution norms worldwide. Here we make an effort to look at some of the measure that the existing marine diesel engine owners can take to reduce emissions and achieve at least levels prescribed in Tier I. Proper maintenance and upkeep of the engine components can be effectively used to reduce the exhaust gas emission. We introduced a pilot program on diesel engine performance monitoring in North America about two years ago and it has yielded quite satisfying results for several shipping companies and more and more ship owners are looking at the option of implementing this program on their ships.

Sign in / Sign up

Export Citation Format

Share Document