scholarly journals Three-dimensional numerical study of thermal exchanges in different geometry sections of mini-channels using three different nanoparticles

10.30544/455 ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 103-119
Author(s):  
Kamel Chadi ◽  
Nourredine Belghar ◽  
Belhi Guerira ◽  
Aissam Messaoudi
Keyword(s):  
Reynolds Number ◽  
Volume Fraction ◽  
Numerical Study ◽  
Three Dimensional ◽  
Numerical Results ◽  
Junction Temperature ◽  
Ansys Fluent ◽  
Cooling Fluid ◽  
Mini Channels ◽  
Exchange Surface

In the present work, we have studied the thermal exchanges of different geometry sections of mini-channels of a cooler numerically. Particularly, we have chosen a mini channels cooler copper for cooling an electronic chip IGBT. In our simulation of three-dimensional (3D), we have compared the numerical results for the different forms of the proposed mini-channels and the three different types of nano-fluids by using the Cu-water, the Ag-water, and the Diamond-water with a volume fraction of 0.02%. The numerical results are obtained by choosing a Reynolds number (Re) between 100 and 900 and considering that the flow regime is stationary. The simulation was performed using commercial software, ANSYS-Fluent 15.0. The results obtained show that the increase of the exchange surface between the walls of the mini channels and the cooling fluid makes increases the heat exchange coefficient and the improvement of the maximum junction temperature of the electronic chip IGBT with the increase of the Reynolds number. The choice of nanoparticles has considerable effects on improving the heat transfer and the maximum junction temperature of the chip IGBT.

Fluid Flow and Lateral Fluid Dispersion in Bounded Granular Beds

2002 ◽  
Author(s):  
Azita Soleymani ◽  
Eveliina Takasuo ◽  
Piroz Zamankhan ◽  
William Polashenski
Keyword(s):  
Reynolds Number ◽  
Porous Media ◽  
Numerical Solutions ◽  
Stokes Equations ◽  
Numerical Study ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Numerical Results ◽  
Transition To Turbulence ◽  
Wide Range

Results are presented from a numerical study examining the flow of a viscous, incompressible fluid through random packing of nonoverlapping spheres at moderate Reynolds numbers (based on pore permeability and interstitial fluid velocity), spanning a wide range of flow conditions for porous media. By using a laminar model including inertial terms and assuming rough walls, numerical solutions of the Navier-Stokes equations in three-dimensional porous packed beds resulted in dimensionless pressure drops in excellent agreement with those reported in a previous study (Fand et al., 1987). This observation suggests that no transition to turbulence could occur in the range of Reynolds number studied. For flows in the Forchheimer regime, numerical results are presented of the lateral dispersivity of solute continuously injected into a three-dimensional bounded granular bed at moderate Peclet numbers. Lateral fluid dispersion coefficients are calculated by comparing the concentration profiles obtained from numerical and analytical methods. Comparing the present numerical results with data available in the literature, no evidence has been found to support the speculations by others for a transition from laminar to turbulent regimes in porous media at a critical Reynolds number.

scholarly journals Numerical study of the turbulent natural convection of nanofluids in a partially heated cubic cavity

2021 ◽  
pp. 57-57
Author(s):  
Zakaria Lafdaili ◽  
Sakina El-Hamdani ◽  
Abdelaziz Bendou ◽  
Karim Limam ◽  
Bara El-Hafad
Keyword(s):  
Nusselt Number ◽  
Natural Convection ◽  
Heat Exchange ◽  
Metallic Nanoparticles ◽  
Volume Fraction ◽  
Numerical Study ◽  
Three Dimensional ◽  
Stability Characteristic ◽  
Horizontal Strip ◽  
Turbulent Natural Convection

In this work we study numerically the three-dimensional turbulent natural convection in a partially heated cubic cavity filled with water containing metallic nanoparticles, metallic oxides and others based on carbon.The objective is to study and compare the effect of the addition of nanoparticles studied in water and also the effect of the position of the heated partition on the heat exchange by turbulent natural convection in this type of geometry, which can significantly improve the design of heat exchange systems for better space optimization. For this we have treated numerically for different volume fractions the turbulent natural convection in the two cases where the cavity is heated respectively by a vertical and horizontal strip in the middle of one of the vertical walls. To take into account the effects of turbulence, we used the standard turbulence model ? - ?. The governing equations are discretized by the finite volume method using the power law scheme which offers a good stability characteristic in this type of flow. The results are presented in the form of isothermal lines and current lines. The variation of the mean Nusselt number is calculated for the two positions of the heated partition as a function of the volume fraction of the nanoparticles studied in water for different Rayleigh numbers.The results show that carbon-based nanoparticles intensify heat exchange by convection better and that the position of the heated partition significantly influences heat exchange by natural convection. In fact, an improvement in the average Nusselt number of more than 20% is observed for the case where the heated partition is horizontal.

scholarly journals Three-dimensional numerical study of mixed convection within a ventilated cavity (Shape ‘ L ‘) crossed by a nanofluid under the effect of a magnetic field

2020 ◽  
Vol 307 ◽  
pp. 01027
Author(s):  
S. KHERROUBI ◽  
K. RAGUI ◽  
N. LABSI ◽  
Y.K. BENKAHLA ◽  
A. BOUTRA
Keyword(s):  
Magnetic Field ◽  
Mixed Convection ◽  
Volume Fraction ◽  
Numerical Study ◽  
Vertical Wall ◽  
Three Dimensional ◽  
Convection Heat Transfer ◽  
Left Wall ◽  
Ventilated Cavity ◽  
The Right

The present work is dedicated to the three-dimensional numerical study of mixed convection heat transfer, taking place within a ventilated cavity (of shape L) crossed by Cu-water nanofluid. The enclosure is subjected to the action of a magnetic field. The ventilation is assured by two openings of the same size. The cold flow enters by an opening practiced at the top of the left wall, and exits by another opening practiced at the bottom of the right vertical wall. All the cavity walls are maintained at the same temperature, superior to that of the entering flow, except the side walls which are considered as adiabatic. The control parameters are: the Reynolds number and the Hartmann number as well as the nanoparticles volume fraction.

PREDICTION OF UNSTEADY STATES IN LID-DRIVEN CAVITIES FILLED WITH AN INCOMPRESSIBLE VISCOUS FLUID

2012 ◽  
Vol 23 (04) ◽  
pp. 1250030 ◽  
Author(s):  
FAYÇAL HAMMAMI ◽  
NADER BEN-CHEIKH ◽  
ANTONIO CAMPO ◽  
BRAHIM BEN-BEYA ◽  
TAIEB LILI
Keyword(s):  
Reynolds Number ◽  
Numerical Study ◽  
Three Dimensional ◽  
Staggered Grid ◽  
Three Dimensional Flow ◽  
Driven Cavity ◽  
Flow Evolution ◽  
2D And 3D ◽  
Benchmark Solutions ◽  
Good Agreement

In this work, a numerical study devoted to the two-dimensional and three-dimensional flow of a viscous, incompressible fluid inside a lid-driven cavity is undertaking. All transport equations are solved using the finite volume formulation on a staggered grid system and multi-grid acceleration. Quantitative aspects of two and three-dimensional flows in a lid-driven cavity for Reynolds number Re = 1000 show good agreement with benchmark results. An analysis of the flow evolution demonstrates that, with increments in Re beyond a certain critical value Rec, the steady flow becomes unstable and bifurcates into unsteady flow. It is observed that the transition from steadiness to unsteadiness follows the classical Hopf bifurcation. The time-dependent velocity distribution is studied in detail and the critical Reynolds number is localized for both 2D and 3D cases. Benchmark solutions for 2D and 3D lid-driven cavity flows are performed for Re = 1500 and 6000.

Numerical Investigation on Turbulence Statistics and Heat Transfer of a Circular Jet Impinging on a Roughened Flat Plate

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Abdulrahman Alenezi ◽  
Abdulrahman Almutairi ◽  
Hamad Alhajeri ◽  
Abdulaziz Gamil ◽  
Faisal Alshammari
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Roughness Element ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Target Plate ◽  
Cross Sectional ◽  
Flow Physics ◽  
Baseline Case

Abstract A detailed heat transfer numerical study of a three-dimensional impinging jet on a roughened isothermal surface is presented and is investigated from flow physics vantage point under the influence of different parameters. The effects of the Reynolds number, roughness location, and roughness dimension on the flow physics and heat transfer parameters are studied. Additionally, the relations between average heat transfer coefficient (AHTC) and flow physics including pressure, wall shear and flow vortices with thermodynamic nonequilibrium are offered. This paper studies the effect of varying both location and dimension of the roughness element which took the shape of square cross-sectional continuous ribs to deliver a favorable trade-off between total pressure loss and heat transfer rate. The roughness element was tested for three different radial locations (R/D) = 1, 1.5, and 2 and at each location its height (i.e., width) (e) was changed from 0.25 to 1 mm in incremental steps of 0.25. The study used a jet angle (α) of 90 deg, jet-to-target distance (H/D = 6), and Re ranges from 10,000 to 50,000, where H is the vertical distance between the target plate and jet exit. The results show that the AHTC can be significantly affected by changing the geometry and dimensions of the roughness element. This variation can be either an augmentation of, or decrease in, the (HTC) when compared with the baseline case. An enhancement of 12.9% in the AHTC was achieved by using optimal location and dimensions of the roughness element at specific Reynolds number. However, a diminution between 10% and 30% in (AHTC) was attained by the use of rib height e = 1 mm at Re = 50k. The variation of both rib location and height showed better contribution in increasing heat transfer for low-range Reynolds numbers.

Study on Heat Transfer and Resistance Characteristics of H-Type Finned Tube

2013 ◽  
Vol 805-806 ◽  
pp. 1817-1822 ◽  
Author(s):  
Zhang Jun Wang ◽  
Zhuo Xiong Zeng ◽  
Yi Hua Xu
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Performance ◽  
Euler Number ◽  
Numerical Study ◽  
Three Dimensional ◽  
Finned Tube ◽  
Comprehensive Performance ◽  
Better Than

Three-dimensional numerical study is performed for heat transfer and resistance characteristics as well as comprehensive performance of two kinds H-type (single and double) finned tube. It is found that the heat transfer and resistance characteristics as well as comprehensive performance of H-type finned tube are influenced by the Reynolds number of gas. With the growth of Reynolds number, the air-side Nusselt number rises gradually and the heat transfer performance gets better and better, whereas the air-side Euler number drops step by step until close to a fixed value. The comprehensive performances of both single H-type finned tube and double ones are weaken progressively. When Reynolds number value is same, the convective heat transfer, pressure drop, air-side Nusselt number and Euler number of single H-type finned tube are bigger than those of double ones. The single H-type finned tube expression is much better than double ones in comprehensive performance and heat transfer.

Effect of Cross Aspect Ratio on Flow in Diverging and Converging Microchannels

2017 ◽  
Vol 139 (6) ◽  
Author(s):  
V. S. Duryodhan ◽  
Shiv Govind Singh ◽  
Amit Agrawal
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Numerical Study ◽  
Three Dimensional ◽  
Hydraulic Diameter ◽  
Working Fluid ◽  
Cross Sectional ◽  
Flow Acceleration ◽  
Three Dimensional Models

Aspect ratio is an important parameter in the study of flow through noncircular microchannel. In this work, three-dimensional numerical study is carried out to understand the effect of cross aspect ratio (height to width) on flow in diverging and converging microchannels. Three-dimensional models of the diverging and converging microchannels with angle: 2–14 deg, aspect ratio: 0.05–0.58, and Reynolds number: 130–280 are employed in the simulations with water as the working fluid. The effects of aspect ratio on pressure drop in equivalent diverging and converging microchannels are studied in detail and correlated to the underlying flow regime. It is observed that for a given Reynolds number and angle, the pressure drop decreases asymptotically with aspect ratio for both the diverging and converging microchannels. At small aspect ratio and small Reynolds number, the pressure drop remains invariant of angle in both the diverging and converging microchannels; the concept of equivalent hydraulic diameter can be applied to these situations. Onset of flow separation in diverging passage and flow acceleration in converging passage is found to be a strong function of aspect ratio, which has not been shown earlier. The existence of a critical angle with relevance to the concept of equivalent hydraulic diameter is identified and its variation with Reynolds number is discussed. Finally, the effect of aspect ratio on fluidic diodicity is discussed which will be helpful in the design of valveless micropump. These results help in extending the conventional formulae made for uniform cross-sectional channel to that for the diverging and converging microchannels.

Numerical study of nanofluid flow and heat transfer over a rotating disk using Buongiorno’s model

2017 ◽  
Vol 27 (1) ◽  
pp. 221-234 ◽  
Author(s):  
Junaid Ahmad Khan ◽  
M. Mustafa ◽  
T. Hayat ◽  
Mustafa Turkyilmazoglu ◽  
A. Alsaedi
Keyword(s):  
Brownian Motion ◽  
Volume Fraction ◽  
Numerical Study ◽  
Mathematical Formulation ◽  
Three Dimensional ◽  
Vertical Direction ◽  
Rotating Disk ◽  
Content Type ◽  
Buongiorno’S Model ◽  
Buongiorno Model

Purpose The purpose of the present study is to explore a three-dimensional rotating flow of water-based nanofluids caused by an infinite rotating disk. Design/methodology/approach Mathematical formulation is performed using the well-known Buongiorno model which accounts for the combined influence of Brownian motion and thermophoresis. The recently suggested condition of passively controlled wall nanoparticle volume fraction has been adopted. Findings The results reveal that temperature decreases with an increase in thermophoresis parameter, whereas it is negligibly affected with a variation in the Brownian motion parameter. Axial velocity is negative because of the downward flow in the vertical direction. Originality/value Two- and three-dimensional streamlines are also sketched and discussed. The computations are found to be in very good agreement with the those of existing studies in the literature for pure fluid.

A Numerical Study on Heat Conductivity Characterization of Aluminium Filled Polypropylene Composites

2012 ◽  
Vol 585 ◽  
pp. 14-18 ◽  
Author(s):  
Alok Agrawal ◽  
Alok Satapathy
Keyword(s):  
Thermal Conductivity ◽  
Finite Element ◽  
Volume Fraction ◽  
Numerical Study ◽  
Three Dimensional ◽  
Heat Transfer Process ◽  
Aluminium Content ◽  
Volume Percentage ◽  
Polypropylene Composites ◽  
Finite Element Package

A numerical simulation of the heat-transfer process within polypropylene matrix composite filled with micro-sized aluminium particles using Finite Element Method is proposed in this paper. Three-dimensional spheres-in-cube lattice array models are constructed to simulate the microstructure of composite materials with aluminium content ranging from about 1.5 to 42 vol% and the effective thermal conductivities of the composites are estimated. A commercially available finite-element package ANSYS is used for this numerical analysis. The result shows that the effective thermal conductivity (Keff) increases with increase in the volume fraction of the aluminium in the composites. The simulated values are compared with calculated Keff values obtained from other established correlations such as Rule-of-Mixture (ROM), Maxwell’s model and with published experimental results. This study reveals that the incorporation of aluminium particles results in enhancement of thermal conductivity of polypropylene thereby increasing its heat transportation capability. It is found that with incorporation of about 42 vol% of 100 micron sized aluminium particles thermal conductivity of the composite increases from 0.239 W/m-K to 0.875 W/m-K. This study also shows that the effect of particle size with same volume percentage on thermal conductivity is marginal.

Numerical Investigation of Turbulent Magnetic Nanofluid Flow inside Straight Channels

2016 ◽  
Vol 819 ◽  
pp. 382-391 ◽  
Author(s):  
Nor Azwadi Che Sidik ◽  
Mohammed Raad Abdulwahab
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Cross Section ◽  
Volume Fraction ◽  
Numerical Study ◽  
Circular Cross Section ◽  
Average Diameter ◽  
Turbulent Regime ◽  
Reynolds Number Increase ◽  
Number Increase

A numerical study using computational fluid dynamics method with an approach of single phase has been presented in order to determine the effects of the concentration of the nanoparticles and flow rate on the convective heat transfer and friction factor in turbulent regime flowing through three different straight channels (straight, circular and triangular) with different Reynolds number (5000 ≤ Re ≤ 20000) using constant applied heat flux. The nanofluid was used consist of Fe3O4 magnetic nanoparticles with average diameter of (13nm) dispersed in water with four volume fraction (0, 0.2, 0.4, 0.6%). The results revealed that as volume fraction and Reynolds number increase Nusselt number increase and the heat transfer rate in circular cross section tube is better than that in square and triangular cross section channels.

Sign in / Sign up

Export Citation Format

Share Document