scholarly journals Investigation and Mathematical Modelling of Optimized Cutting Parameters for Surface Roughness of EN-8 Alloy Steel

2021 ◽  
Vol 4 (2) ◽  
Author(s):  
Amit Saraswat ◽  
Dipak Kumar
Keyword(s):  
Surface Roughness ◽  
Response Surface ◽  
Alloy Steel ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Lower Surface ◽  
Depth Of Cut ◽  
Surface Model ◽  
Design Matrix ◽  
Work Done

The work done in this work deals with the efficacy of cutting parameters on surface of EN-8 alloy steel. For knowing the optimal effects of cutting parameters response surface methodology was practiced subjected to central composite design matrix. The motive was to introduce an interaction among input parameters, i.e., cutting speed, feed and depth of cut and output parameter, surface roughness. For this, second order response surface model was modeled. The foreseen values obtained were found to be fairly close to observed values, showed that the model could be practiced to forecast the surface roughness on EN-8 within the range of parameter studied. Contours and 3-D plots are generated to forecast the value of surface roughness. It was revealed that surface roughness decreases with increases in cutting speed and it increases with feed. However, there were found negligible or almost no implication of depth of cut on surface roughness whereas feed rate affected the surface roughness most. For lower surface roughness, the optimum values of each one were also evaluated.

Surface Roughness Prediction in End Milling of Machinable Glass Ceramic and Optimization by Response Surface Methodology

2011 ◽  
Vol 189-193 ◽  
pp. 1376-1381
Author(s):  
Moola Mohan Reddy ◽  
Alexander Gorin ◽  
Khaled A. Abou El Hossein
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Glass Ceramic ◽  
End Milling ◽  
Removal Rate ◽  
Cutting Speed ◽  
Lower Surface ◽  
Depth Of Cut ◽  
Machining Parameters

This paper presents the prediction of a statistically analyzed model for the surface roughness,R_a of end-milled Machinable glass ceramic (MGC). Response Surface Methodology (RSM) is used to construct the models based on 3-factorial Box-Behnken Design (BBD). It is found that cutting speed is the most significant factor contributing to the surface roughness value followed by the depth of cut and feed rate. The surface roughness value decreases for higher cutting speed along with lower feed and depth of cut. Additionally, the process optimization has also been done in terms of material removal rate (MRR) to the model’s response. Ideal combinations of machining parameters are then suggested for common goal to achieve lower surface roughness value and higher MRR.

scholarly journals Optimization of Cutting Parameters on Turning Process Based on Surface Roughness Using Response Surface Methodology

2011 ◽  
Vol 117-119 ◽  
pp. 1561-1565
Author(s):  
Muhammad Yusuf ◽  
Mohd Khairol Anuar Ariffin ◽  
N. Ismail ◽  
S. Sulaiman
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Process ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting ◽  
Optimization Of Cutting Parameters

This paper describes effect of cutting parameters on surface roughness for turning of aluminium alloy 7050 using carbide cutting tool with dry cutting condition. The model is developed based on cutting speed, feed rate and depth of cut as the parameters of cutting process. The selection of cutting process was based on the design of experiments Response Surface Methodology (RSM). The objective of this research is finding the optimum cutting parameters based on surface roughness. The relation between cutting parameters and surface roughness were discussed.

Response Surface Modeling and Optimization of Cutting Temperature in Turning of AISI 52100 Hardened Alloy Steel under Minimal Cutting Fluid Application

2021 ◽  
Vol 106 ◽  
pp. 60-67
Author(s):  
Sandip Mane ◽  
Sanjay Kumar
Keyword(s):  
Response Surface ◽  
Alloy Steel ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Temperature Response ◽  
Cutting Parameters ◽  
Cutting Fluid ◽  
Critical Parameters ◽  
Depth Of Cut ◽  
Aisi 52100

The heat generation and subsequent temperature rise in the cutting zone due to plastic deformation and friction at tool-chip-workpiece interface are critical parameters that have a significant impact on tool wear, tool life and surface integrity. This paper aimed to analyse the effect of cutting parameters such as, cutting speed, feed and depth of cut on the cutting temperature in turning of hardened AISI 52100 alloy steel of 58 HRC using multilayer coated carbide cutting tool insert under high velocity pulsing jet minimal cutting fluid application (MCFA) environment. Response surface methodology based central composite design (CCD) was used to investigate and optimize the cutting parameters on cutting temperature response. The quadratic regression model in terms of cutting speed, feed and depth of cut for cutting temperature was developed. The diagnostic and confirmatory tests were carried out to check its validity. The implication of the process parameters and their interactions were tested using analysis of variance (ANOVA). The results showed that the cutting speed and feed were the main significant parameters affecting the cutting temperature, while depth of cut and quadratic term of cutting speed had a moderate effect. The predictive model developed indicates the 99% desirability level in turning of AISI 52100 hardened steel under the MCFA environment. The predicted values of cutting temperature response are in close agreement with the experimental results.

Assessment of Factors Influencing Tool Wear on the Machining of Nimonic C-263 Alloy with PVD Coated Carbide Inserts

2011 ◽  
Vol 291-294 ◽  
pp. 794-799 ◽  
Author(s):  
Chakaravarthy Ezilarasan ◽  
Ke Zhu ◽  
A Velayudham ◽  
K. Palanikumar
Keyword(s):  
Tool Wear ◽  
Response Surface ◽  
Flank Wear ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Surface Model ◽  
Power Generators ◽  
Optimal Value ◽  
Coated Carbide

Nimonic C-263 alloy is extensively used in the field of like aerospace, power generators and heat exchangers due to its higher thermal properties. In this work, an attempt has been made to investigate the effect of the cutting parameters (cutting speed, feed rate & depth of cut) on tool wear (flank wear) in the machining of this alloy with a PVD coated carbide insert. The experiments were conducted using Taguchi’s experimental design. A second order response surface model has been established between the cutting parameters and flank wear using response surface methodology. The predicted optimal value of flank wear for coated carbide is 0.190mm. The results are confirmed by conducting verification experiments.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

OPTIMISING CUTTING PARAMETERS FOR HOT TURNING ON EN31 MATERIAL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Prof. Hemant k. Baitule ◽  
Satish Rahangdale ◽  
Vaibhav Kamane ◽  
Saurabh Yende
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Multiple Time ◽  
Turning Process ◽  
Workpiece Material ◽  
Hot Turning

In any type of machining process the surface roughness plays an important role. In these the product is judge on the basis of their (surface roughness) surface finish. In machining process there are four main cutting parameter i.e. cutting speed, feed rate, depth of cut, spindle speed. For obtaining good surface finish, we can use the hot turning process. In hot turning process we heat the workpiece material and perform turning process multiple time and obtain the reading. The taguchi method is design to perform an experiment and L18 experiment were performed. The result is analyzed by using the analysis of variance (ANOVA) method. The result Obtain by this method may be useful for many other researchers.

Evaluation of Process Parameters in Machining of AA6063 Alloy

2018 ◽  
Vol 1148 ◽  
pp. 109-114
Author(s):  
M. Balaji ◽  
C.H. Nagaraju ◽  
V.U.S. Vara Prasad ◽  
R. Kalyani ◽  
B. Avinash
Keyword(s):  
Surface Roughness ◽  
Regression Analysis ◽  
Process Parameters ◽  
Single Channel ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Roughness Parameters ◽  
Surface Roughness Parameters ◽  
Aa6063 Alloy

The main aim of this work is to analyse the significance of cutting parameters on surface roughness and spindle vibrations while machining the AA6063 alloy. The turning experiments were carried out on a CNC lathe with a constant spindle speed of 1000rpm using carbide tool inserts coated with Tic. The cutting speed, feed rate and depth of cut are chosen as process parameters whose values are varied in between 73.51m/min to 94.24m/min, 0.02 to 0.04 mm/rev and 0.25 to 0.45 mm respectively. For each experiment, the surface roughness parameters and the amplitude plots have been noted for analysis. The output data include surface roughness parameters (Ra,Rq,Rz) measured using Talysurf and vibration parameter as vibration amplitude (mm/sec) at the front end of the spindle in transverse direction using single channel spectrum analyzer (FFT).With the collected data Regression analysis is also performed for finding the optimum parameters. The results show that significant variation of surface irregularities and vibration amplitudes were observed with cutting speed and feed. The optimum cutting speed and feed from the regression analysis were 77.0697m/min and 0.0253mm/rev. for the minimum output parameters. No significant effect of depth of cut on output parameters is identified.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

Improvement of Surface Roughness in End Milling of Ti6Al4V by Coupling RSM with Genetic Algorithm

2011 ◽  
Vol 264-265 ◽  
pp. 1154-1159
Author(s):  
Anayet Ullah Patwari ◽  
A.K.M. Nurul Amin ◽  
S. Alam
Keyword(s):  
Genetic Algorithm ◽  
Surface Roughness ◽  
Titanium Alloys ◽  
End Milling ◽  
Fitness Function ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Resistance Surface

Titanium alloys are being widely used in the aerospace, biomedical and automotive industries because of their good strength-to-weight ratio and superior corrosion resistance. Surface roughness is one of the most important requirements in machining of Titanium alloys. This paper describes mathematically the effect of cutting parameters on Surface roughness in end milling of Ti6Al4V. The mathematical model for the surface roughness has been developed in terms of cutting speed, feed rate, and axial depth of cut using design of experiments and the response surface methodology (RSM). Central composite design was employed in developing the surface roughness models in relation to primary cutting parameters. The experimental results indicate that the proposed mathematical models suggested could adequately describe the performance indicators within the limits of the factors that are being investigated. The developed RSM is coupled as a fitness function with genetic algorithm to predict the optimum cutting conditions leading to the least surface roughness value. MATLAB 7.0 toolbox for GA is used to develop GA program. The predicted results are in good agreement with the experimental one and hence the model can be efficiently used to achieve the minimum surface roughness value.

scholarly journals Investigations on Surface Roughness and Tool Wear Characteristics in Micro-Turning of Ti-6Al-4V Alloy

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2998 ◽  
Author(s):  
Kubilay Aslantas ◽  
Mohd Danish ◽  
Ahmet Hasçelik ◽  
Mozammel Mia ◽  
Munish Gupta ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Removal Rate ◽  
Cutting Speed ◽  
Small Diameter ◽  
Cutting Parameters ◽  
Ti6al4v Alloy ◽  
Depth Of Cut ◽  
Turning Process ◽  
Micro Turning

Micro-turning is a micro-mechanical cutting method used to produce small diameter cylindrical parts. Since the diameter of the part is usually small, it may be a little difficult to improve the surface quality by a second operation, such as grinding. Therefore, it is important to obtain the good surface finish in micro turning process using the ideal cutting parameters. Here, the multi-objective optimization of micro-turning process parameters such as cutting speed, feed rate and depth of cut were performed by response surface method (RSM). Two important machining indices, such as surface roughness and material removal rate, were simultaneously optimized in the micro-turning of a Ti6Al4V alloy. Further, the scanning electron microscope (SEM) analysis was done on the cutting tools. The overall results depict that the feed rate is the prominent factor that significantly affects the responses in micro-turning operation. Moreover, the SEM results confirmed that abrasion and crater wear mechanism were observed during the micro-turning of a Ti6Al4V alloy.

Sign in / Sign up

Export Citation Format

Share Document