scholarly journals Performance investigation of a volute porous tongue of a turbocharger turbine

2020 ◽  
Vol 40 (1) ◽  
pp. 59-66
Author(s):  
Abderrahmane Chachoua ◽  
Mohamed Kamal Hamidou ◽  
Mohammed Hamel
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Gas Turbines ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Recirculation Flow ◽  
Recirculating Flow ◽  
Show Evidence ◽  
The Right

The design for better performance of the spiral housing volute used commonly in radial and mixed inflow gas turbines is of prime importance as it affects the machine stage at both design and off design conditions. The tongue of the scroll divides the flow into two streams, and represents a severe source of disturbances, in terms of thermodynamic parameter uniformity, maximum kinetic energy, the right angle of attack to the rotor and minimum losses. Besides, the volute suffers an undesirable effect due to the recirculating mass flow rate in near bottom vicinity of the tongue. The present project is an attempt to design a tongue fitted with cylindrical holes traversing normal to the stream wise direction, where on account of the large pressure difference between the top and the bottom sides of the tongue will force the recirculating flow to go through the rotor inlet. This possibility with its limitations has not yet been explored. A numerical simulation is performed which might provide our suitable objectives. To achieve this goal the ANSYS code is used to build the geometry, generate the mesh, and to simulate the flow by solving numerically the averaged Navier Stokes equations. Apparently, the numerical results show evidence of favorable impact in using porous tongue. The realization of a contact between the main and recirculation flow by drilled holes on the tongue surface leads to a flow field uniformity, a reduction in the magnitude of the loss coefficient, and a 20 % reduction in the recirculating mass flow rate.

scholarly journals Development of Hybrid Airlift-Jet Pump with Its Performance Analysis

2018 ◽  
Vol 8 (9) ◽  
pp. 1413 ◽  
Author(s):  
Dan Yao ◽  
Kwongi Lee ◽  
Minho Ha ◽  
Cheolung Cheong ◽  
Inhiug Lee
Keyword(s):  
Boundary Conditions ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Stokes Equations ◽  
Flow Characteristics ◽  
Operating Conditions ◽  
Navier Stokes ◽  
Jet Pump ◽  
Two Phase

A new pump, called the hybrid airlift-jet pump, is developed by reinforcing the advantages and minimizing the demerits of airlift and jet pumps. First, a basic design of the hybrid airlift-jet pump is schematically presented. Subsequently, its performance characteristics are numerically investigated by varying the operating conditions of the airlift and jet parts in the hybrid pump. The compressible unsteady Reynolds-averaged Navier-Stokes equations, combined with the homogeneous mixture model for multiphase flow, are used as the governing equations for the two-phase flow in the hybrid pump. The pressure-based methods combined with the Pressure-Implicit with Splitting of Operators (PISO) algorithm are used as the computational fluid dynamics techniques. The validity of the present numerical methods is confirmed by comparing the predicted mass flow rate with the measured ones. In total, 18 simulation cases that are designed to represent the various operating conditions of the hybrid pump are investigated: eight of these cases belong to the operating conditions of only the jet part with different air and water inlet boundary conditions, and the remaining ten cases belong to the operating conditions of both the airlift and jet parts with different air and water inlet boundary conditions. The mass flow rate and the efficiency are compared for each case. For further investigation into the detailed flow characteristics, the pressure and velocity distributions of the mixture in a primary pipe are compared. Furthermore, a periodic fluctuation of the water flow in the mass flow rate is found and analyzed. Our results show that the performance of the jet or airlift pump can be enhanced by combining the operating principles of two pumps into the hybrid airlift-jet pump, newly proposed in the present study.

scholarly journals Differential Throttling and Fluidic Thrust Vectoring in a Linear Aerospike

2021 ◽  
Vol 6 (2) ◽  
pp. 8
Author(s):  
Michele Ferlauto ◽  
Andrea Ferrero ◽  
Matteo Marsicovetere ◽  
Roberto Marsilio
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Combustion Chambers ◽  
Thrust Vectoring ◽  
Fluidic Thrust Vectoring

Aerospike nozzles represent an interesting solution for Single-Stage-To-Orbit or clustered launchers owing to their self-adapting capability, which can lead to better performance compared to classical nozzles. Furthermore, they can provide thrust vectoring in several ways. A simple solution consists of applying differential throttling when multiple combustion chambers are used. An alternative solution is represented by fluidic thrust vectoring, which requires the injection of a secondary flow from a slot. In this work, the flow field in a linear aerospike nozzle was investigated numerically and both differential throttling and fluidic thrust vectoring were studied. The flow field was predicted by solving the Reynolds-averaged Navier–Stokes equations. The thrust vectoring performance was evaluated in terms of side force generation and axial force reduction. The effectiveness of fluidic thrust vectoring was investigated by changing the mass flow rate of secondary flow and injection location. The results show that the response of the system can be non-monotone with respect to the mass flow rate of the secondary injection. In contrast, differential throttling provides a linear behaviour but it can only be applied to configurations with multiple combustion chambers. Finally, the effects of different plug truncation levels are discussed.

Experimental and Numerical Investigations on the Aerodynamic Performance of the Three-Stage Turbine With Consideration of the Leakage Flow Effect

2016 ◽  
Author(s):  
Yang Chen ◽  
Jun Li ◽  
Chaoyang Tian ◽  
Gangyun Zhong ◽  
Xiaoping Fan ◽  
...  
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotor Blade ◽  
Three Dimensional ◽  
Aerodynamic Performance ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Leakage Flows ◽  
Wheel Disk

The aerodynamic performance of three-stage turbine with different types of leakage flows was experimentally and numerically studied in this paper. The leakage flows of three-stage turbine included the shroud seal leakage flow between the rotor blade tip and case, the diaphragm seal leakage flow between the stator blade diaphragm and shaft, as well as the shaft packing leakage flow and the gap leakage flow between the rotor blade curved fir-tree root and wheel disk. The total aerodynamic performance of three-stage turbine including leakage flows was firstly experimentally measured. The detailed flow field and aerodynamic performance were also numerically investigated using three-dimensional Reynolds-Averaged Navier-Stokes (RANS) and S-A turbulence model. The numerical mass flow rate and efficiency showed well agreement with experimental data. The effects of leakage flows between the fir-tree root and the wheel disk were studied. All leakage mass flow fractions, including the mass flow rate in each hole for all sets of root gaps were given for comparison. The effect of leakage flow on the aerodynamic performance of three-stage was illustrated and discussed.

Design and Testing of a Can Combustor for a Small Gas Turbine Application

2013 ◽  
Author(s):  
K. V. L. Narayana Rao ◽  
N. Ravi Kumar ◽  
G. Ramesha ◽  
M. Devathathan
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Gas Turbines ◽  
Pressure Loss ◽  
High Energy ◽  
Experimental Results ◽  
High Mass ◽  
Test Facility ◽  
Design Requirements

Can type combustors are robust, with ease of design, manufacturing and testing. They are extensively used in industrial gas turbines and aero engines. This paper is mainly based on the work carried out in designing and testing a can type combustion chamber which is operated using JET-A1 fuel. Based on the design requirements, the combustor is designed, fabricated and tested. The experimental results are analysed and compared with the design requirements. The basic dimensions of the combustor, like casing diameter, liner diameter, liner length and liner hole distribution are estimated through a proprietary developed code. An axial flow air swirler with 8 vanes and vane angle of 45 degree is designed to create a re-circulation zone for stabilizing the flame. The Monarch 4.0 GPH fuel nozzle with a cone angle of 80 degree is used. The igniter used is a high energy igniter with ignition energy of 2J and 60 sparks per minute. The combustor is modelled, meshed and analysed using the commercially available ansys-cfx code. The geometry of the combustor is modified iteratively based on the CFD results to meet the design requirements such as pressure loss and pattern factor. The combustor is fabricated using Ni-75 sheet of 1 mm thickness. A small combustor test facility is established. The combustor rig is tested for 50 Hours. The experimental results showed a blow-out phenomenon while the mass flow rate through the combustor is increased beyond a limit. Further through CFD analysis one of the cause for early blow out is identified to be a high mass flow rate through the swirler. The swirler area is partially blocked and many configurations are analysed. The optimum configuration is selected based on the flame position in the primary zone. The change in swirler area is implemented in the test model and further testing is carried out. The experimental results showed that the blow-out limit of the combustor is increased to a good extent. Hence the effect of swirler flow rate on recirculation zone length and flame blow out is also studied and presented. The experimental results showed that the pressure loss and pattern factor are in agreement with the design requirements.

Influence of Steam Injection on Thermal Efficiency and Operating Temperature of GE-F5 Gas Turbines Applying VODOLEY System

2005 ◽  
Author(s):  
Mohsen Ghazikhani ◽  
Nima Manshoori ◽  
Davood Tafazoli
Keyword(s):  
Power Plant ◽  
Ambient Temperature ◽  
Gas Turbine ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Steam Injection ◽  
Gas Turbine Cycle

An industrial gas turbine has the characteristic that turbine output decreases on hot summer days when electricity demand peaks. For GE-F5 gas turbines of Mashad Power Plant when ambient temperature increases 1° C, compressor outlet temperature increases 1.13° C and turbine exhaust temperature increases 2.5° C. Also air mass flow rate decreases about 0.6 kg/sec when ambient temperature increases 1° C, so it is revealed that variations are more due to decreasing in the efficiency of compressor and less due to reduction in mass flow rate of air as ambient temperature increases in constant power output. The cycle efficiency of these GE-F5 gas turbines reduces 3 percent with increasing 50° C of ambient temperature, also the fuel consumption increases as ambient temperature increases for constant turbine work. These are also because of reducing in the compressor efficiency in high temperature ambient. Steam injection in gas turbines is a way to prevent a loss in performance of gas turbines caused by high ambient temperature and has been used for many years. VODOLEY system is a steam injection system, which is known as a self-sufficient one in steam production. The amount of water vapor in combustion products will become regenerated in a contact condenser and after passing through a heat recovery boiler is injected in the transition piece after combustion chamber. In this paper the influence of steam injection in Mashad Power Plant GE-F5 gas turbine parameters, applying VODOLEY system, is being observed. Results show that in this turbine, the turbine inlet temperature (T3) decreases in a range of 5 percent to 11 percent depending on ambient temperature, so the operating parameters in a gas turbine cycle equipped with VODOLEY system in 40° C of ambient temperature is the same as simple gas turbine cycle in 10° C of ambient temperature. Results show that the thermal efficiency increases up to 10 percent, but Back-Work ratio increases in a range of 15 percent to 30 percent. Also results show that although VODOLEY system has water treatment cost but by using this system the running cost will reduce up to 27 percent.

Mass Flow Rate Measurements: From Hydrodynamic to Free Molecular Regime

2008 ◽  
Author(s):  
Timothe´e Ewart ◽  
Irina A. Graour ◽  
Pierre Perrier ◽  
J. Gilbert Me´olans
Keyword(s):  
Mass Flow Rate ◽  
Knudsen Number ◽  
Mass Flow ◽  
Flow Rate ◽  
Stationary Flow ◽  
Small Mass ◽  
Accommodation Coefficient ◽  
Navier Stokes ◽  
Number Range ◽  
Free Molecular Regime

An experimental investigation in a single silica microtube in isothermal stationary flow for various gases is made from the hydrodynamic to the near free molecular regime to study the reflection/accommodation process at the wall. This kind of investigation requires, more than other Micro-Electro-Mechanical-Systems (MEMS) experiments, a powerful experimental platform to measure very small mass flow rate. A global analytic expression, based on the Navier-Stokes (NS) equations with second order boundary conditions, is used to yield the Tangential Momentum Accommodation Coefficient (TMAC) in 0.003–0.3 Knudsen number range. Otherwise, the experimental results of the mass flow rate is compared with theoretical values calculated from kinetic approaches using variable TMAC as fitting parameter over the 0.3–30 Knudsen number range. Finally, whatever the theoretical approach the TMAC values obtained from the different gas-surface pairs are rather close one to other, but the TMAC values seem decreasing when the molecular mass increases.

Unsteady Interaction Between Annulus and Turbine Rim Seal Flows

2012 ◽  
Author(s):  
Martin Chilla ◽  
Howard Hodson ◽  
David Newman
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Gas Turbines ◽  
Measurement Data ◽  
Design Flow ◽  
Flow Conditions ◽  
Disc Space ◽  
Flow Interaction ◽  
The Impact

In core gas turbines relatively cold air is purged through the hub gap between stator and rotor in order to seal the disc space against flow ingestion from the main annulus. Although the sealing mass flow rate is commonly very small compared to the main annulus mass flow rate, it can have significant effects on the development of the passage endwall flows and on the overall loss generation. In this paper, the interaction between annulus and rim sealing flows is investigated using numerical simulations of a generic high-pressure turbine. At first, the numerical approach is validated by comparing the results of calculations to measurement data at the design flow conditions. Following that, results from steady and unsteady calculations are used to describe in detail the aerodynamics in overlap-type rim seals and their effects on the blade passage flow. It is found that the flow interaction at the rim seal interface is strongly influenced by the velocity deficit of the rim sealing flow relative to the annulus flow as well as by the circumferentially non-uniform pressure field imposed by the rotor blades. At typical sealing flow conditions, the flow interaction is found to be naturally unsteady, with periodical vortex shedding into the rotor passage. Finally, the influence of the specific rim seal shape on the flow unsteadiness at the rim seal interface is investigated and the impact on turbine performance is assessed.

Experimental Study on the Performance of a See-Through Labyrinth Seal With Two-Phase, Mainly-Liquid Mixtures

2021 ◽  
Vol 143 (1) ◽  
Author(s):  
Min Zhang ◽  
Dara W. Childs
Keyword(s):  
Experimental Study ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Gas Turbines ◽  
Labyrinth Seal ◽  
Test Fluid ◽  
Inlet Temperature ◽  
Pump Rotor ◽  
Piston Seal

Abstract With the increasing demand of the oil and gas industry, many pump companies are developing multiphase pumps, which can handle liquid–gas flow directly without separating the liquid from a mixed flow. The see-through labyrinth seal is one of the popular types of noncontact annular seals that act as a balancing piston seal to reduce the axial thrust of a high-performance centrifugal pump. The see-through labyrinth seal also generates reaction forces that can significantly impact the rotordynamic performance of the pump. Multiphase pumps are expected to operate from pure-liquid to pure-gas conditions. Zhang and Childs (2019) (Zhang, M., and Childs, D., 2019, “A Study on the Leakage and Rotordynamic Performance of a Long Labyrinth Seal Under Mainly-Air Conditions,” ASME J. Eng. Gas Turbines Power, 141(12), p. 121024) conducted a comprehensive experimental study on the performance (leakage and rotordynamic coefficients) of a see-through labyrinth seal under mainly gas conditions. This paper continues Zhang and Childs (2019) (Zhang, M., and Childs, D., 2019, “A Study on the Leakage and Rotordynamic Performance of a Long Labyrinth Seal Under Mainly-Air Conditions,” ASME J. Eng. Gas Turbines Power, 141(12), p. 121024) research and studies the performance of the see-through tooth-on-stator labyrinth seal under mainly liquid conditions. The test seal's inner diameter, length, and radial clearance are 89.256 mm, 66.68 mm, and 0.178 mm, respectively. The test fluid is a mixture of air and paper silicone oil (PSF-5cSt), and the inlet gas volume fraction (GVF) varies from zero to 12%. Tests are conducted at an exit pressure of 6.9 bars, an inlet temperature of 39.1 °C, three pressure drops (PDs) (27.6 bars, 34.5 bars, and 48.3 bars), and three rotating speeds ω (5 krpm, 10 krpm, and 15 krpm). The seal is always concentric with the rotor, and there is no intentional fluid prerotation at the seal inlet. The air presence in the oil flow significantly impacts the leakage as well as the dynamic forces of the test seal. The first air increment (increasing inlet GVF from 0% to 3%) slightly increases the leakage mass flow rate, while further air increments steadily decrease the leakage mass flow rate. For all test conditions, the leakage mass flow rate does not change as ω increases from 5 krpm to 10 krpm but decreases as ω is further increased to 15 krpm. The reduction in the leakage mass flow rate indicates that there is an increase in the friction factor, and there could be a highly possible flow regime change as ω increases from 10 krpm to 15 krpm. For ω ≤ 10 krpm, effective stiffness Keff increases as inlet GVF increases. Keff represents the test seal's total centering force on the pump rotor. The increase of Keff increases the seal's centering force and would increase the pump rotor's critical speeds. Ceff indicates the test seal's total damping force on the pump rotor. For ω ≤ 10 krpm, Ceff first decreases as inlet GVF increases from zero to 3%, and then remains unchanged as inlet GVF is further increased to 12%. For ω = 15 krpm, Keff first increases as inlet GVF increases from zero to 3% and then decreases as inlet GVF is further increased. As inlet GVF increases, Ceff steadily decreases for ω = 15 krpm.

An analytically predictive model for moderately rarefied gas flow

2012 ◽  
Vol 698 ◽  
pp. 406-422 ◽  
Author(s):  
Thomas Veltzke ◽  
Jorg Thöming
Keyword(s):  
Mass Flow ◽  
Flow Rate ◽  
Stokes Equations ◽  
Rarefied Gas ◽  
Knudsen Diffusion ◽  
Convective Transport ◽  
Surface Topology ◽  
Fickian Diffusion ◽  
Navier Stokes ◽  
Navier Stokes Equations

AbstractIn microducts deviation from continuum flow behaviour of a gas increases with rarefaction. When using Navier–Stokes equations to calculate a flow under slightly and moderately rarefied conditions, slip boundary conditions are used which in turn refer to the tangential momentum accommodation coefficient (TMAC). Here we demonstrate that, in the so-called slip and transition regime, the flow in microducts can be reliably described by a consistently non-empirical model without considering the TMAC. We obtain this equation by superposition of convective transport and Fickian diffusion using two-dimensional solutions of Navier–Stokes equations and a description for the Knudsen diffusion coefficient as derived from kinetic theory respectively. For a wide variety of measurement series found in the literature the calculation predicts the data accurately. Surprisingly only size of the duct, temperature, gas properties and inlet and outlet pressure are necessary to calculate the resulting mass flow by means of a single algebraic equation. From this, and taking the discrepancies of the TMAC concerning surface roughness and nature of the gases into account, we could conclude that neither the diffusive proportions nor the total mass flow rates are influenced by surface topology and chemistry at Knudsen numbers below unity. Compared to the tube geometry, the model slightly underestimates the flow rate in rectangular channels when rarefaction increases. Likewise, the dimensionless mass flow rate and the diffusive proportion of the total flow are distinctly higher in a tube. Thus the cross-sectional geometry has a significant influence on the transport mechanisms under rarefied conditions.

Power Enhancement of Gas Turbine Plant by Intake Air Fog Cooling

2015 ◽  
Vol 3 (1) ◽  
Author(s):  
J. P. Yadav ◽  
Bharat Raj Singh ◽  
Onkar Singh
Keyword(s):  
Gas Turbine ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Power Output ◽  
Gas Turbines ◽  
Ambient Air ◽  
Summer Season ◽  
Ambient Conditions ◽  
Power Enhancement

Although gas turbines are known as constant volume machines, but its performance considerably depends upon the ambient air temperature and mass flow rate. During summer season the density of the air decreases which affects the mass flow rate and ultimately the power output of a gas turbine is reduced. In order to overcome this situation several techniques are already in the practice and one of the most effective and economical is adopting the inlet fog cooling, and this technique basically enhances the power output of the machine. The cooling of ambient air by fog cooling up to wet bulb temperature increases the mass flow rate on account of increase in air density, as a result it ultimately increases the power output of a gas turbine. Fogging is applied with consideration of relative humidity of ambient air not only during summer season but also during dry days of summer season in order to increase the power output of gas turbine. This paper describes the effect on percentage enhancement of power out adopting various fuel options with low and high humidity ambient conditions. The result indicates the potential increase in the power output up to 14%. It is also observed that the total cost of power production increases due to increase in fuel consumption on account of enhanced power output. Thus the best suitable selling cost of power should be selected to compensate the increased investment on fuel cost.

Sign in / Sign up

Export Citation Format

Share Document