scholarly journals Evaluation of the Effect of Complete and Partial Osseointegration in Stress Development at Bone-Implant Interface: A 3D Finite Element Study

2016 ◽  
Vol 6 (2) ◽  
pp. 24-27
Author(s):  
Bashu Raj Pandey ◽  
Hemant Kumar Halwai ◽  
Khushbu Adhikari ◽  
Amresh Thakur
Keyword(s):  
Finite Element ◽  
Cortical Bone ◽  
Cancellous Bone ◽  
Element Model ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Bone Implant ◽  
Stress Development ◽  
Bone Segment ◽  
Von Mises

Introduction: Mini-implant has been in use as temporary anchorage device in orthodontics. Various factors like length, type of osseointegration, magnitude and direction of force, insertion angle of the mini-implant affect the stress development at the bone and implant interface. Development of undesirable stress at the bone-implant interface can lead to bone defect and failure of the implant. Various opinions regarding the need of osseointegration have been reported.Objective: To study the effect of complete and partial osseointegration on Von Mises stress distribution at the bone-implant interface.Materials & Method: Finite element model of 9mm × 1.5mm mini-implant and bone segment of 1.5mm were constructed to simulate the biomechanical response of the bone to the mini- implant by using CATIA V5-6R 2013 software. Stress developed on implant and bone were analyzed by using ANSYS: 13 2013 version software for both complete and partial level of osseointegration.Result: Maximum Von Mises stress in complete osseointegration was 14.49 Mpa in cortical bone, 0.551 Mpa in cancellous bone and 50.76 Mpa in implant. In partial osseointegration, it was 18.68 Mpa in cortical bone, 1.23 Mpa in cancellous bone and 66.80 Mpa in mini-implant.Conclusion: In partial osseointegration, stress developed was higher but well below the yield strength of respected continuum. So the partial osseointegration is a good compromise between the necessity of reducing mobility of implant and the necessity for easier screw removal. Key words: cancellous bone, cortical bone, Finite element analysis, mini-implant, Von Mises stress

Comparison of Plate-Screw Systems Used in Mandibular Fracture Reduction: Finite Element Analysis

2006 ◽  
Vol 128 (5) ◽  
pp. 654-662 ◽  
Author(s):  
Scott T. Lovald ◽  
Tariq Khraishi ◽  
Jon Wagner ◽  
Bret Baack ◽  
James Kelly ◽  
...  
Keyword(s):  
Finite Element ◽  
Cancellous Bone ◽  
Reduction Potential ◽  
Element Model ◽  
Fracture Reduction ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Von Mises ◽  
Relative Differences ◽  
Tomography Data

A finite element model of the human dentate mandible has been developed to provide a comparison of fixation systems used currently for fracture reduction. Volume domains for cortical bone, cancellous bone, and teeth were created and meshed in ANSYS 8.0 based on IGES curves created from computerized tomography data. A unilateral molar clench was loaded on the model with a fracture gap simulated along the symphysis. Results based on Von Mises stress in cortical and cancellous bone surrounding the screws, and on fracture surface spatial fixation, show some relative differences between different screw-plate systems, yet all were judged to be appropriate in their reduction potential.

An Improved Control Arm Design for a Commercial Vehicle

2021 ◽  
Author(s):  
Sinan Yıldırım ◽  
Ufuk Çoban ◽  
Mehmet Çevik
Keyword(s):  
Finite Element ◽  
Cost Effective ◽  
Element Model ◽  
Tensile Tests ◽  
The Body ◽  
Von Mises Stress ◽  
Driving Safety ◽  
Design Development ◽  
Element Analysis ◽  
Von Mises

Suspension linkages are one of the fundamental structural elements in each vehicle since they connect the wheel carriers i.e. axles to the body of the vehicle. Moreover, the characteristics of suspension linkages within a suspension system can directly affect driving safety, comfort and economics. Beyond these, all these design criteria are bounded to the package space of the vehicle. In last decades, suspension linkages have been focused on in terms of design development and cost reduction. In this study, a control arm of a diesel public bus was taken into account in order to get the most cost-effective design while improving the strength within specified boundary conditions. Due to the change of the supplier, the control arm of a rigid axle was redesigned to find an economical and more durable solution. The new design was analyzed first by the finite element analysis software Ansys and the finite element model of the control arm was validated by physical tensile tests. The outputs of the study demonstrate that the new design geometry reduces the maximum Von Mises stress 15% while being within the elastic region of the material in use and having found an economical solution in terms of supplier’s criteria.

Finite Element Analysis of Gold Bonding under Different Loading Conditions

2014 ◽  
Vol 607 ◽  
pp. 713-716
Author(s):  
Wen Liang Tang ◽  
Chun Yue Huang ◽  
Tian Ming Li ◽  
Ying Liang ◽  
Guo Ji Xiong ◽  
...  
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Simulation Software ◽  
Bonding Time ◽  
Von Mises Stress ◽  
Bonding Pressure ◽  
Element Analysis ◽  
Von Mises ◽  
Three Dimensional Finite Element

In this paper, ANSYS-LSDYNA simulation software is used to build the three-dimensional finite element model of the ball bond and to get the Von Mises stress. The change of stress about the bump is researched which base on the model in different bonding pressure, bonding power and bonding time. The result show that: The stress increase with bonding pressure increase within a certain bonding pressure range, and then the stress will maintain a table number, however, the stress will continue to increase when the bonding pressure reach a certain value; increasing the bonding power, the area of lager stress will grow; prolonging the bonding time, the stress of the pad will increase with time, but when time increase to a certain value, the stress of the pad will not increase over time.

scholarly journals Influence of PEEK Coating on Hip Implant Stress Shielding: A Finite Element Analysis

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Jesica Anguiano-Sanchez ◽  
Oscar Martinez-Romero ◽  
Hector R. Siller ◽  
Jose A. Diaz-Elizondo ◽  
Eduardo Flores-Villalba ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Cancellous Bone ◽  
Stress Shielding ◽  
Design Concept ◽  
Von Mises Stress ◽  
Hip Implants ◽  
Element Analysis ◽  
Stress Transmission ◽  
Von Mises

Stress shielding is a well-known failure factor in hip implants. This work proposes a design concept for hip implants, using a combination of metallic stem with a polymer coating (polyether ether ketone (PEEK)). The proposed design concept is simulated using titanium alloy stems and PEEK coatings with thicknesses varying from 100 to 400 μm. The Finite Element analysis of the cancellous bone surrounding the implant shows promising results. The effective von Mises stress increases between 81 and 92% for the complete volume of cancellous bone. When focusing on the proximal zone of the implant, the increased stress transmission to the cancellous bone reaches between 47 and 60%. This increment in load transferred to the bone can influence mineral bone loss due to stress shielding, minimizing such effect, and thus prolonging implant lifespan.

Finite Element Analysis of Screw-Plate Systems for Fixation of Parasymphyseal Fractures of the Mandible

2007 ◽  
Vol 23 (1) ◽  
pp. 69-77 ◽  
Author(s):  
Scott T. Lovald ◽  
Tariq Khraishi ◽  
John Wood ◽  
Jon Wagner ◽  
Bret Baack ◽  
...  
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Point Of View ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Fracture Region ◽  
Modeling Practices ◽  
Orthotropic Properties ◽  
Von Mises ◽  
Early Healing

AbstractFinite Element Modeling was used to compare the efficacy of common screw-plate configurations used for fixation of parasymphyseal fractures of the mandible. Measures of Von Mises stress on the screw bone interface, as well as principal strain in the reduced fracture region, were used in this comparison. This study also explored differences between orthotropic and isotropic modeling practices and compared the effect of mastication forces on both the fractured and intact halves of the mandible. The results of this analysis showed no major differences between configurations from a mechanistic point of view. This suggests that the use of any of the studied screw-plate configurations will not increase chances for post-operative complications. Furthermore, little difference is seen between analyses with either orthotropic or isotropic material properties. The inclusion of orthotropic properties can thus be avoided in future studies with similar boundary and plating conditions. Mastication ipsilateral to the fracture increases Von Mises stress 2 to 4 times, and should be avoided during early healing periods. These recommendations only apply to patients whose fractures mimic the finite-element model.

Evaluation of Biomechanical Health Degree of Peri-Implant Bone Through Finite Element Analysis: A First Approach

2018 ◽  
Vol 10 (09) ◽  
pp. 1850097 ◽  
Author(s):  
Junxiong Lin ◽  
Ge Zhang ◽  
Zhenyu Jiang ◽  
Liqun Tang ◽  
Keqian Lian
Keyword(s):  
Finite Element ◽  
Stress State ◽  
Critical Role ◽  
Control Sample ◽  
Stress Shielding ◽  
Element Model ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Computer Tomography Scan ◽  
Von Mises

The biomechanical health degree of peri-implant bone plays a critical role during the service of implants. This paper presents a preliminary exploration of the quantitative evaluation of the biomechanical health degree for the bone tissues around dental implant through finite element method. The finite element model of a part of mandible with three molars is constructed based on computer tomography scan image as a control sample, which is supposed to represent a healthy state. The model of treated mandible is made by replacing the middle tooth in the healthy model with a commercial implant. A regional average strain energy density (RASED) is proposed as a more accurate index to describe the stress state of peri-implant bone tissues, compared with the widely used maximum equivalent von Mises stress. The simulation shows that the stress state in peri-implant bone, i.e., the distribution and level of stress, is highly dependent on the modulus of implant material. Among the implants made of materials with various moduli, including Ti, stainless steel, zirconia, porous Ti, dentin material and polyether-ether-ketone (PEEK), the ones with medium modulus (15–40[Formula: see text]GPa) are found to achieve relatively healthy stress states. This study provides an effective tool to assess the risk of overloading or stress shielding in peri-implant bone tissues. It demonstrates a great potential in the optimization of design, production and usage of implants.

Coupled Thermal Analysis on Carbide Anvil of Cubic Press

2014 ◽  
Vol 852 ◽  
pp. 629-633
Author(s):  
Xian Jun Zhou ◽  
Zhong Wen Xu ◽  
Ren Quan Chen ◽  
Shao Ping Li
Keyword(s):  
Thermal Analysis ◽  
Finite Element ◽  
Shear Stress ◽  
Element Model ◽  
Heat Transfer Analysis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Material Defects ◽  
Indirect Coupling ◽  
Von Mises

Based on finite element analysis software ANSYS, the 3D contact finite element model of carbide anvil, steel ring and cushion block were built to make heat transfer analysis, and the temperature field distribution was obtained. The indirect coupling thermal analysis of carbide anvil, steel ring and cushion block were made regarding as a whole, the Von Mises stress nephogram of them and the shear stress nephogram of carbide anvil were displayed. The stress nephogram revealed that it was liable to fracture on the edge of top surface under high pressure status, and it was also proven that the main reason of fracture was the yield of internal material defects under the action of shear stress.

Finite Element Analysis for the Mega Columns for XRL West Kowloon Terminus

2013 ◽  
Vol 405-408 ◽  
pp. 1139-1143
Author(s):  
Wei Su ◽  
Ying Sun ◽  
Shi Qing Huang ◽  
Ren Huai Liu
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Parametric Design ◽  
Three Dimensional ◽  
Element Model ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Von Mises ◽  
Three Dimensional Finite Element

Using ANSYS parametric design language, a three-dimensional finite element model is developed to analyze the stress distribution and the strength of the mega columns for XRL West Kowloon Terminus. The detailed von Mises stress distribution in each column, vertical stiffener plates and the diaphragm plates is obtained. From the analysis, the phenomenon of stress concentration is obvious in both upper and lower diaphragm plates. The local value of von Mises stress in them is higher than the yield stress value, which must be avoided by more detailed local structural design.

scholarly journals Computerized Generation and Finite Element Stress Analysis of Endodontic Rotary Files

2021 ◽  
Vol 11 (10) ◽  
pp. 4329
Author(s):  
Victor Roda-Casanova ◽  
Álvaro Zubizarreta-Macho ◽  
Francisco Sanchez-Marin ◽  
Óscar Alonso Ezpeleta ◽  
Alberto Albaladejo Martínez ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Computer Aided Design ◽  
Element Model ◽  
Transverse Load ◽  
Von Mises Stress ◽  
Design Parameters ◽  
Element Analysis ◽  
Design Skills ◽  
Von Mises

Introduction: The finite element method has been extensively used to analyze the mechanical behavior of endodontic rotary files under bending and torsional conditions. This methodology requires elevated computer-aided design skills to reproduce the geometry of the endodontic file, and also mathematical knowledge to perform the finite element analysis. In this study, an automated procedure is proposed for the computerized generation and finite element analysis of endodontic rotary files under bending and torsional conditions. Methods: An endodontic rotary file with a 25mm total length, 0.25mm at the tip, 1.20mm at 16mm from the tip, 2mm pitch and squared cross section was generated using the proposed procedure and submitted for analysis under bending and torsional conditions by clamping the last 3mm of the endodontic rotary file and applying a transverse load of 0.1N and a torsional moment of 0.3N·cm. Results: The results of the finite element analyses showed a maximum von Mises stress of 398MPa resulting from the bending analysis and a maximum von Mises stress of 843MPa resulting from the torsional analysis, both of which are next to the encastre point. Conclusions: The automated procedure allows an accurate description of the geometry of the endodontic file to be obtained based on its design parameters as well as a finite element model of the endodontic file from the previously generated geometry.

scholarly journals Biomechanical behavior of overdentures supported by different implant position and angulation using Micro ERA® system

2019 ◽  
Vol 18 ◽  
pp. e191667
Author(s):  
Felipe Franco Ferreira ◽  
Guilherme Almeida Borges ◽  
Letícia Del Rio Silva ◽  
Daniele Valente Velôso ◽  
Thaís Barbin ◽  
...  
Keyword(s):  
Finite Element ◽  
Tensile Stress ◽  
Equivalent Stress ◽  
Lateral Incisor ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Bone Implant ◽  
Implant Position ◽  
Biomechanical Behavior ◽  
Von Mises

Aim: The aim of this study was to investigate the biomechanical behavior of implant-retained mandibular overdentures using Micro ERA® system with different implant position and angulation by finite element analysis (FEA). Methods: Four 3D finite element models of simplified mandibular overdentures were constructed, using one Bränemark implant with a Micro ERA® attachment. The implant was positioned on the canine or lateral incisor area with an angulation of either 0º (C-0º; LI-0º) or 17º (C-17º, LI-17º) to the vertical axis. A 100 N axial load was applied in one side simultaneously, from first premolar to second molar. In all models it was analyzed the overdenture displacement, compressive/tensile stress in the bone-implant interface, and also the von Mises equivalent stress for the nylon component of the housing. The stresses were obtained (numerically and color-coded) for further comparison among all the groups. Results: The displacement on the overdenture was higher at the posterior surface for all groups, especially in the C-17º group. When comparing the compressive/tensile stress in the bone-implant interface, the lateral-incisor groups (LI-0º and LI-17º) had the highest compressive and lowest tensile stress compared to the canine groups (C-0º and C-17º). The von Mises stress on the nylon component generated higher stress value for the LI-0º among all groups. Conclusions: The inclination and positioning of the implant in mandibular overdenture interferes directly in the stress distribution. The results showed that angulated implants had the highest displacement. While the implants placed in the lateral incisor position presented lower compressive and higher tensile stress respectively. For the attachment the canine groups had the lowest stress.

Sign in / Sign up

Export Citation Format

Share Document