scholarly journals CUTTING STONE BUILDING MATERIALS WITH CUT WHEELS OF CUBIC BORON NITRIDE

2021 ◽  
Vol 3 (2) ◽  
pp. 52-63
Author(s):  
A. Bespalova ◽  
◽  
O. Dashkovskaya ◽  
O. Faizulyna ◽  
V. Lebedev ◽  
...  
Keyword(s):  
Cutting Force ◽  
Building Materials ◽  
Heating Temperature ◽  
Cutting Temperature ◽  
Limiting Factor ◽  
Metal Base ◽  
Cutting Power ◽  
Temperature Resistance ◽  
Stone Materials ◽  
Processing Modes

The advantage of cutting stone building materials with SSM (synthetic superhard materials) wheels is that, first of all, it is possible to obtain high processing productivity and dimensional stability, which are 3..5 and 50…100 times higher than those of traditional tools based on carborundum, respectively. The study of the process of cutting stone materials with CBN (cubic boron nitrite) wheels is aimed at establishing force dependences, determining the cutting power and heating temperature of the cutting disc during operation. The forces were measured using a tensometric dynamometer UDM-50. To measure and calculate the cutting temperature, a thermoelectric method based on the formation of practically not inertial microthermocouples during cutting was used. The temperature to which the CBN cutting wheel on a metal base is heated is a limiting factor in processing, since when heated to a temperature of 600ºС, the strength of the wheel decreases by half, which can cause its rupture under the action of centrifugal forces, as well as loss of stability and jamming during cutting. In the present study, the wheel temperature was measured after one minute of continuous operation. The values of the component of the cutting force PY, depending on the processing modes, can reach values of the order of 70 N. The values of the component of the cutting force PZ, depending on the processing modes, can reach values of 45 N. The cutting power can be 2800W. The temperature resistance of the wheel (heating time of the wheel up to 600ºС) when cutting dry is maximum 28 minutes, when grinding with cooling of the cutting zone with negative temperature air from a Ranque-Hilsch tube, the temperature resistance is 35 minutes, with ejector cooling of sprayed coolant 37 minutes and with jet-pressure cooling it is 40 minutes. The maximum cutting length is respectively 0.7: 0.8; 0.9 and 2m. The cutting power is 600...2800W.

scholarly journals Influence of tool edge form factor and cutting parameters on milling performance

2021 ◽  
Vol 13 (4) ◽  
pp. 168781402110090
Author(s):  
Xuefeng Zhao ◽  
Hao Qin ◽  
Zhiguo Feng
Keyword(s):  
Form Factor ◽  
Simulation Model ◽  
Cutting Force ◽  
Surface Quality ◽  
High Speed ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Tool Edge ◽  
Drag Finishing ◽  
Edge Preparation

Tool edge preparation can improve the tool life, as well as cutting performance and machined surface quality, meeting the requirements of high-speed and high-efficiency cutting. In general, prepared tool edges could be divided into symmetric or asymmetric edges. In the present study, the cemented carbide tools were initially edge prepared through drag finishing. The simulation model of the carbide cemented tool milling steel was established through Deform software. Effects of edge form factor, spindle speed, feed per tooth, axial, and radial cutting depth on the cutting force, the tool wear, the cutting temperature, and the surface quality were investigated through the orthogonal cutting simulation. The simulated cutting force results were compared to the results obtained from the orthogonal milling experiment through the dynamometer Kistler, which verified the simulation model correctness. The obtained results provided a basis for edge preparation effect along with high-speed and high effective cutting machining comprehension.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Simulation of Machining of Incoloy 907 Based on Thermodynamical Constitutive Equation

2013 ◽  
Vol 631-632 ◽  
pp. 681-685
Author(s):  
Fang Shao ◽  
Fa Qing Li ◽  
Hai Ying Zhang ◽  
Xuan Gao
Keyword(s):  
Cutting Force ◽  
Cutting Temperature ◽  
Tool Material ◽  
High Reactivity ◽  
Good Prediction ◽  
Workpiece Material ◽  
Element Analysis ◽  
Good Prediction Accuracy ◽  
Experimental Cutting ◽  
Cutting Tool Materials

Aero-engine alloys (also as known as superalloys)are known as difficult-to-machine materials, especially at higher cutting speeds, due to their several inherent properties such as low thermal conductivity and their high reactivity with cutting tool materials. In this paper a finite element analysis (FEA) of machining for Incoloy907 is presented. In particular, the thermodynamical constitutitve equation(T-C-E) in FEA is applied for both workpiece material and tool material. Cutting temperature and cutting force are predicted. The comparison between the predicted and experimental cutting temperature and cutting force are presented and discussed. The results indicated that a good prediction accuracy of both principal cutting temperature and cutting force can be achieved by the method of FEA with thermodynamical constitutitve equation.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

Study of the Effect of Tool Wear on Cutting Ti6Al4V Process

2013 ◽  
Vol 690-693 ◽  
pp. 2030-2035
Author(s):  
Shu Bao Yang ◽  
Hong Chao Ni ◽  
Guo Hui Zhu
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
Cutting Temperature ◽  
Chip Morphology ◽  
Key Factors ◽  
Serrated Chip ◽  
Comprehensive Properties ◽  
Commercial Applications ◽  
On Chip ◽  
Rapid Tool

Ti6Al4V alloy is widely used in the aircraft industry, marine and the commercial applications due to its excellent comprehensive properties. However, its poor machinability prevents it from application widely, and the rapid tool wear is one of the key factors. The FEM models of cutting titanium alloy are established. The effect of tool wear on chip morphology, cutting temperature and cutting force are studied. The simulation results show that: the cutting force and cutting temperature will rise with the increase of tool wear. Furthermore, the degree of chip deformation will improve, but the frequency of serrated chip tooth occurred will decrease.

scholarly journals Influence of Ultrasonic Vibration-Assisted Ball-End Milling on the Cutting Performance of AZ31B Magnesium Alloy

2020 ◽  
Vol 9 (4) ◽  
pp. 271-276
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Ultrasonic Vibration ◽  
Biomedical Applications ◽  
End Milling ◽  
Cutting Temperature ◽  
Cutting Performance ◽  
Machining Process ◽  
Dry Conditions ◽  
Good Biocompatibility

Magnesium alloys have a tremendous possibility for biomedical applications due to their good biocompatibility, integrity and degradability, but their low ignition temperature and easy corrosive property restrict the machining process for potential biomedical applications. In this research, ultrasonic vibration-assisted ball milling (UVABM) for AZ31B is investigated to improve the cutting performance and get specific surface morphology in dry conditions. Cutting force and cutting temperatures are measured during UVABM. Surface roughness is measured with a white light interferometer after UVABM. The experimental results show cutting force and cutting temperature reduce due to ultrasonic vibration, and surface roughness decreases by 34.92%, compared with that got from traditional milling, which indicates UVABM is suitable to process AZ31B for potential biomedical applications.

scholarly journals Analytical, FEA, And Experimental Research of 2D-Vibration Assisted Cutting ( 2D-VAC) In Titanium Alloy Ti6Al4V

2021 ◽  
Author(s):  
Rendi Kurniawan ◽  
Farooq Ahmed ◽  
Gun Chul Park ◽  
Tae Jo Ko
Keyword(s):  
Residual Stress ◽  
Plastic Strain ◽  
Cutting Force ◽  
Frequency Modulation ◽  
High Frequency ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Von Mises Stress ◽  
Micro Hardness ◽  
Micro Structure

Abstract In the 2D-Vibration Assisted Cutting (2D-VAC) method, the cutting tool shakes in a 2-dimensional approach because of superimposed high-frequency modulation. This high-frequency modulation effect creates a displacement at a tiny scale of micrometers and causes an escalation in the resultant cutting speed. Consequently, 2D-VAC has superior advantages compared to traditional cutting (TC). This manuscript describes research on 2D-VAC that focuses on modeling cutting forces (mathematical model) and finite element analysis (FEA) results. The FEA results are focused on the von Mises stress, plastic strain, cutting force, cutting temperature, and residual stress. In addition, an experiment for the chip formation, micro-structure layer, and micro-hardness was also analyzed in this study. According to the modeling results, the cutting force has a comparable pattern to the FEA results. The stress contour result confirms that the 2D-VAC method has lower stress than that in the TC method during tool retraction mode. Additionally, the plastic strain in the 2D-VAC method can be higher than that in the TC method. According to the temperature results, the peak temperature in the 2D-VAC could be higher than that in the TC method. The residual stress shows that there is a compressive effect. Thus, the compressive stress is higher than that in the TC method. Micro-hardness results confirmed that there is not too much change from the original surface in the 2D-VAC method. The result of micro-structure morphology also confirmed that there is a significant shear deformation flow in case of the TC method, although less occurs in the 2D-VAC method.

scholarly journals Research on Cutting Force and Surface Integrity of TC18 Titanium Alloy by Longitudinal Ultrasonic Vibration Assisted Milling

2021 ◽  
Author(s):  
Weibo Xie ◽  
Xikui Wang ◽  
Erbo Liu ◽  
Jian Wang ◽  
Xiaobin Tang ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Cutting Force ◽  
Ultrasonic Vibration ◽  
Surface Integrity ◽  
Rotational Speed ◽  
Three Dimensional ◽  
Cutting Temperature ◽  
Surface Residual Stress ◽  
Deformation Layer ◽  
Vibration Milling

Abstract In order to study the influence of rotational speed and amplitude on the surface integrity, TC18 titanium alloy samples were milled by the process of conventional milling and longitudinal ultrasonic vibration assisted milling. The experimental data were obtained by dynamometer, thermometer, scanning electron microscope, X-ray diffractometer and three-dimensional surface topography instrument for observation and analysis. The results show that the rotational speed has a significant effect on the cutting force, cutting temperature, surface morphology and surface residual stress. Compared with ordinary milling, the surface micro-texture produced by ultrasonic vibration milling is more regular, , and with the increase of rotational speed, the influence of ultrasonic vibration on cutting force and cutting temperature decrease. There are adverse effects on surface roughness after ultrasonic vibration superposition. The influence of ultrasonic vibration on the surface residual compressive stress is also greatly reduced when the rotational speed is greater than 2400 rpm. In addition, a certain depth of plastic deformation layer can be formed under the surface of ultrasonic vibration machining, and the depth of deformation layer increases with the increase of vibration.

A Metallo-Thermomechanically Coupled Analysis of Orthogonal Cutting of AISI 1045 Steel

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Hongtao Ding ◽  
Yung C. Shin
Keyword(s):  
Experimental Data ◽  
Cutting Force ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Chip Morphology ◽  
Machining Process ◽  
Coupled Analysis ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel

Materials often behave in a complicated manner involving deeply coupled effects among stress/stain, temperature, and microstructure during a machining process. This paper is concerned with prediction of the phase change effect on orthogonal cutting of American Iron and Steel Institute (AISI) 1045 steel based on a true metallo-thermomechanical coupled analysis. A metallo-thermomechanical coupled material model is developed and a finite element model (FEM) is used to solve the evolution of phase constituents, cutting temperature, chip morphology, and cutting force simultaneously using abaqus. The model validity is assessed using the experimental data for orthogonal cutting of AISI 1045 steel under various conditions, with cutting speeds ranging from 198 to 879 m/min, feeds from 0.1 to 0.3 mm, and tool rake angles from −7 deg to 5 deg. A good agreement is achieved in chip formation, cutting force, and cutting temperature between the model predictions and the experimental data.

Experimental Investigation of Mechanical-Thermal Characteristics in High Efficiency Turning Titanium Alloy Ti6Al4V

2016 ◽  
Vol 836-837 ◽  
pp. 20-28
Author(s):  
Li Min Shi ◽  
Cheng Yang ◽  
Qi Jun Li
Keyword(s):  
Titanium Alloy ◽  
Tool Wear ◽  
Cutting Force ◽  
High Efficiency ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Thermal Characteristics ◽  
Tool Failure ◽  
Minimal Quantity Lubrication ◽  
Titanium Alloy Ti6al4v

Titanium alloy Ti6Al4V has poor machinability, which leads to high unit cutting force and cutting temperature, rapid tool failure. In this study, the effect of the cutting speed, feed rate and cooling condition on cutting force and cutting temperature is critically analysed by turning experiment. At the same time, the relationship is established among tool wear, cutting force and cutting temperature. This investigation has shown that cutting speed is the decisive factor which increasing cutting force and cutting temperature. In the process of turning, tool wear results in high amounts of heat and mechanical stress, which leads to serious tool wear. The Minimal Quantity Lubrication reduces the frictional condition at the chip-tool, decreases cutting force and cutting temperature, and delays the tool failure.

Sign in / Sign up

Export Citation Format

Share Document