scholarly journals EFFECT OF ARTIFICIAL CAVITIES ON HEAT TRANSFER AND FLOW CHARACTERISTICS MICROCHANNEL

2019 ◽  
Vol 20 (3) ◽  
pp. 180-192
Author(s):  
Suha A. Mohammed ◽  
Ekhlas M. Fayyadh
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Friction Factor ◽  
Single Phase ◽  
Flow Characteristics ◽  
Channel Length ◽  
Bottom Surface ◽  
Inlet Temperature ◽  
Micro Channel

An experimental investigation was conducted to study single-phase fluid flow and heat transfer in a copper micro channel. To investigate the effect of artificial cavities on fluid flow and single phase heat transfer in micro channel heat sink, two model of straight micro channel recognized as two models (model -1and model -2) were designed and manufactured ,where model-1 have smooth bottom surface while Model-2 have 47 artificial cavities distributed uniformly at the bottom surface along the micro channel length. The two models having the same nominal dimension of 300?m height and 300?m depth while the real dimension value are 367 ?m for width and 296 ?m for depth .De-ionized water was used as the working fluids. Experimental test was conducted at 30?C inlet temperature with Reynolds numbers range from 700 to 2200 covering laminar flow conditions. The experiments were conducted with horizontal micro channel under both adiabatic (for friction factor calculation) and diabatic (for Nusselt number calculation) conditions. The results indicated that the experimental Darcy friction factor can be predicted well with conventional scale fanning friction factor correlations for developing flow in laminar region by shah and London (1978) correlation for two models. Also, the experimental Nusselt number Agree well with each correlation of shah and London (1978) and Mirmanto correlation in laminar region.

Pressure Drop and Heat Transfer in a Single-Phase Micro-Pin-Fin Heat Sink

2006 ◽  
Author(s):  
Abel M. Siu Ho ◽  
Weilin Qu ◽  
Frank Pfefferkorn
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Heat Sink ◽  
Single Phase ◽  
Fluid Transport ◽  
Heat Sinks ◽  
Inlet Temperature ◽  
Pin Fin

The pressure drop and heat transfer characteristics of a single-phase micro-pin-fin heat sink were investigated experimentally. Fabricated from 110 copper, the heat sink consisted of 1950 staggered micro-pins with 200×200 μm2 cross-section by 670 μm height. Deionized water was employed as the cooling liquid. A coolant inlet temperature of 25°C, and two heat flux levels, q" eff = 50 W/cm2 and q" eff = 100 W/cm2, defined relative to the planform area of the heat sink, were tested. The inlet Reynolds number ranged from 93 to 634 for q" eff = 50 W/cm2, and 127 to 634 for q" eff = 100 W/cm2. The measured pressure drop and temperature distribution were used to evaluate average friction factor and local averaged heat transfer coefficient/Nusselt number. Predictions of the Moores and Joshi friction factor correlation and the Chyu et al. heat transfer correlation that were developed using macro-size pin-fin arrays were compared to micro-pin-fin heat sink data. While the Moores and Joshi correlation provide acceptable predictions, the Chyu et al. correlation overpredicted local Nusselt number data by a fairly large margin. These findings point to the need for further study of single-phase thermal/fluid transport process in micro-pin-fin heat sinks.

Experimental analysis on thermal and friction factor characteristics of fluid flow in tube with novel double strip helical screw tape

2019 ◽  
Vol 234 (6) ◽  
pp. 874-886
Author(s):  
Shashank R Chaurasia ◽  
RM Sarviya
Keyword(s):  
Nusselt Number ◽  
Fluid Flow ◽  
Friction Factor ◽  
Experimental Analysis ◽  
Flow Characteristics ◽  
Performance Ratio ◽  
Working Fluid ◽  
Flow Rates ◽  
Twist Ratio ◽  
Single Strip

An experimental analysis has been carried out to investigate the thermal and friction factor characteristics of fluid flow in a tube with double strip helical screw tape (DS-HST) inserts with different values of twist ratio and compared with single strip helical screw tape inserts and plain tube. Water is used as a working fluid at different flow rates with constant heat flux conditions. CFD analysis is also carried out to visualize thermal and fluid flow characteristics of fluid flow in tube with inserts. Experimental results have showed that Nusselt number and friction factor have attained excellent enhancement with double strip helical screw tape inserts in the range of flow rates than single strip helical screw tape inserts at the value of twist ratio 1.5. Correlation is also developed for Nusselt number with a range of Reynolds number, twist ratio and number of strips. Moreover, the performance ratio has attained maximum value at twist ratio of 2.5 with high values of flow rate. It is concluded that DS-HST is able to attain enhancement in the efficiency of heat exchanger, causing a reduction in size for thermal applications.

Numerical Analysis on Flow Characteristics of Anti-Gravity Flow

2011 ◽  
Author(s):  
Yan Li ◽  
Shuchao Zhang ◽  
Ning Mei
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Fluid Flow ◽  
Flow Characteristics ◽  
Gravity Flow ◽  
Radius Of Curvature ◽  
Micro Channel ◽  
Subcooled Boiling ◽  
Evaporation Heat ◽  
Micro Channels

Fluid flow phenomena in micro channels received wide attention due to its high heat transfer coefficient. As a new technique in the field of micro channel phase-change heat transfer, anti-gravity flow can drive fluid flow by capillary force and create enhanced evaporation heat transfer conditions by promoting the formation of an extended meniscus in the three-phase contact-line region. Resulting from the circumferential discrepancy of degree of superheat, the radius of curvature of intrinsic meniscus decreases rapidly as liquid rising up, leading to the formation of capillary pressure gradient. With the increase of heat flux, subcooled boiling occurs and micro-bubble appears at the bottom of the fluted tube. Under the action of buoyancy and drag force, the bubble rises along the channel and at the same time grows continually for the presence of superheat until its break. This paper focuses on the numerical study of flow characteristics of anti-gravity flow in the micro channel and the influence of bubble under the subcooled boiling circumstance. The results shows that bubble plays a positive role in the formation of anti-gravity flow and the analytical expressions are presented for the rising velocity of liquid, the contact angle and the curvature of the intrinsic meniscus, which are all influenced by heat flux, superheat temperature and the geometric parameters of the channel.

Local Single-Phase Heat Transfer Research of Natural Circulation in Narrow Rectangular Channel

2017 ◽  
Author(s):  
Zhiqiang Zhu ◽  
Xiaxin Cao ◽  
Changqi Yan ◽  
Chunping Tian
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Inclination Angle ◽  
Local Nusselt Number ◽  
Single Phase ◽  
Natural Circulation ◽  
Rectangular Channel ◽  
Inlet Temperature

In order to explore and analyze the heat transfer characteristics in narrow rectangular channel, experiments on local single-phase heat transfer of natural circulation in a one-side heating narrow rectangular channel have been conducted under vertical and inclined condition. The thermotechnical parameters such as inlet temperature, heat flux and inclination angle varies during the experiments. The width of the flow channel is 40 mm and the narrow gap is 2 mm. It is heated from one side with a homogeneous and constant heat flux and the working medium is deionized water. Based on the experimental results, under vertical condition, the driving force in the loop goes up and the Reynolds number also increases when the inlet temperature is elevated, which causes an increase in local Nusselt number. When the heat flux rises, the local Nusselt number increases and the heat transfer temperature difference increases. The local Nusselts number is influenced by entrance effect and the entrance region length is computed for laminar and turbulent flow. Under inclined condition, with the inclination angle from −30° to 30°, it is found that when the inclination angle is positive, the local Nusselt number in fully developed region is larger than that under vertical condition and increases with the angle value, even though the Reynolds number decreases by the effect of incline. This phenomenon is explained by giving an analysis of the natural convection, which is characterized by the normal Grashof number, in the direction perpendicular to the heating plat. Moreover, the variation of heat transfer is also interpreted on the basis of field coordination principle. However, when the inclination angle is negative, the heat transfer shows no obvious difference between vertical condition and inclined condition.

scholarly journals Experimental investigation of the effect of wave turbulators on heat transfer in pipes

2021 ◽  
pp. 183-183
Author(s):  
Sendogan Karagoz ◽  
Semih Erzincanli ◽  
Orhan Yildirim ◽  
Ilker Firat ◽  
Mehmet Kaya ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Factor ◽  
Enhancement Factor ◽  
Single Phase ◽  
Reynolds Numbers ◽  
Nusselt Numbers ◽  
Thermal Enhancement ◽  
Enhancement Factors ◽  
Thermal Enhancement Factor

This experimental study deals with the heat transfer and friction effects of sinusoidal part turbulators for single-phase flows occurring in a circular shaped pipe. Turbulators with three different radius values are placed in the pipe to make the flow turbulent. In this way, changes in Nusselt number and friction coefficient are examined. As a result of the experiments made with Reynolds numbers in the range of 6614-20710, the increase rates of the Nusselt numbers of turbulators with 20 mm, 110 mm and 220 mm radius compared to the empty pipe were obtained as 153.49%, 85.36%, and 52.09%, respectively. As a result of the decrease in the radius, there was an increase in the Nusselt number and the friction factor. Parallel to the Nusselt number, the highest friction factor was obtained in the smallest radius turbulator. It was found that the thermal enhancement factors of 110 mm and 220 mm radius turbulators increased by 179.54% and 132.95%, respectively, compared to the 20 mm radius turbulator. Similarly, it was determined that the thermal enhancement factor of the 110 mm radius turbulator increased by 20% compared to the 220 mm radius turbulator.

Numerical Simulation of Flow and Heat Transfer Inside a Micro-Channel With One Dimpled Surface

2002 ◽  
Author(s):  
X. J. Wei ◽  
Y. K. Joshi ◽  
P. M. Ligrani
Keyword(s):  
Heat Transfer ◽  
Flow Characteristics ◽  
Secondary Flows ◽  
Bottom Surface ◽  
Micro Channel ◽  
Rectangular Microchannel ◽  
Micro Scale ◽  
Recirculating Flow ◽  
Flow And Heat Transfer ◽  
Macro Scale

Steady, laminar flow and heat transfer, inside a rectangular microchannel with a dimpled bottom surface, are numerically studied using FLUENT 5.5. The microchannel is 50 μm deep and 200 μm wide. The dimples are placed in a single row of along the bottom wall with a pitch of 150 μm. The dimple depth is 20 μm, and the dimple print diameter is 98 μm. Fully developed periodic velocity and temperature boundary conditions are used at the inlet and outlet of one unit cell of the dimpled micro-channel. The numerically predicted, laminar, micro-scale flow characteristics are compared to results from macro-scale studies with turbulent flow. Some of the secondary flows into and out of the dimple, and the recirculating flow within the dimple are similar for both situations. However, the type and number of vortex structures shed from the dimples are significantly different for the laminar-micro-scale flow and turbulent-macro-scale flow. Heat transfer enhancements are present for both situations, but they are somewhat smaller in the laminar-micro-scale flow. In the latter case, these augmentations (relative to a channel with smooth walls) are present both on the bottom-dimpled surface, and on the sidewalls of the channel, and are mostly due to shear layer reattachment, secondary flows produced near the edges of the dimples, and thermal boundary layer thinning. The pressure drop penalties in the laminar-micro-scale flow are either equivalent to, or less than values produced in smooth channels with no dimples.

Numerical Study of Flow and Heat Transfer Enhancement by Using Delta Winglets in a Triangular Wavy Fin-and-Tube Heat Exchanger

2009 ◽  
Vol 131 (9) ◽  
Author(s):  
Liting Tian ◽  
Yaling He ◽  
Pan Chu ◽  
Wenquan Tao
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Numerical Study ◽  
Attack Angle ◽  
Geometrical Parameters ◽  
Tube Heat Exchanger ◽  
Delta Winglet

In this paper, three-dimensional numerical simulations with renormalization-group (RNG) k-ε model are performed for the air-side heat transfer and fluid flow characteristics of wavy fin-and-tube heat exchanger with delta winglet vortex generators. The Reynolds number based on the tube outside diameter varies from 500 to 5000. The effects of different geometrical parameters with varying attack angle of delta winglet (β=30 deg, β=45 deg, and β=60 deg), tube row number (2–4), and wavy angle of the fin (θ=0–20 deg) are examined. The numerical results show that each delta winglet generates a downstream main vortex and a corner vortex. The longitudinal vortices are disrupted by the downstream wavy trough and only propagate a short distance along the main flow direction but the vortices greatly enhance the heat transfer in the wake region behind the tube. Nusselt number and friction factor both increase with the increase in the attack angle β, and the case of β=30 deg has the maximum value of j/f. The effects of the tube row number on Nusselt number and friction factor are very small, and the heat transfer and fluid flow become fully developed very quickly. The case of θ=5 deg has the minimum value of Nusselt number, while friction factor always increases with the increase in wavy angle. The application of delta winglet enhances the heat transfer performance of the wavy fin-and-tube heat exchanger with modest pressure drop penalty.

Experimental Study on Thermal-Hydraulic Performance of Single-Phase Water Flow in Narrow Rectangular Channel

2009 ◽  
Author(s):  
Mei Wang ◽  
Yan Wen ◽  
Suizheng Qiu ◽  
Guanghui Su ◽  
Weifeng Ni
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Friction Factor ◽  
Water Flow ◽  
Single Phase ◽  
Rectangular Channel ◽  
Flow Region ◽  
Phase Water

The purpose of this study is to discover the differences of pressure drop and heat transfer of single-phase water flow between conventional channels and narrow rectangular channels. Furthermore, the differences between the level and the vertical channel have been studied. The gap of the test channel is 1.8mm. Compared with conventional channels, the narrow rectangular channel showed differences in both flow and heat transfer characteristics. The critical Reynolds number of transition from laminar flow to turbulent flow is 900∼1300, which is smaller compared with conventional channels. The friction factor is larger than that of the conventional channels and the correlation of friction factor with Reynolds number was given by experimental results. From the relation graph of Nusselt number and Reynolds number, the demarcation of the laminar flow region and turbulence flow region is obvious. In laminar region, Nusselt number almost remained constant and approximately consistent with numerical simulation results. While in turbulent region, Nusselt number increased significantly with increasing Reynolds number. A new Nusselt number correlation was obtained based on Dittus-Boelter equation, and the coefficients were less about 13% than that of Dittus-Boelter equation.

scholarly journals INVESTIGATION OF SINGLE-PHASE FLOW CHARACTERISTICS IN A STAGGER PIN-FINS COMPLEX GEOMETRY

2021 ◽  
Vol 25 (6) ◽  
pp. 74-81
Author(s):  
R. Shakir ◽  
Keyword(s):  
Heat Transfer ◽  
Single Phase ◽  
Complex Geometry ◽  
Flow Characteristics ◽  
Inlet Temperature ◽  
Phase Flow ◽  
Fluid Temperature ◽  
Single Phase Flow ◽  
Pin Fins ◽  
Micro Pin Fins

The cooling equipment project must use electrical and electronic equipment because of the need to remove the heat generated by this equipment. Investigation; R-113 single-phase flow heat transfer; (50 x 50 mm2) cross-section and (5 mm) height; used in a series of stagger-square micro-pin fins. Inlet temperature of (25 °C); (6) Mass flow rate at this temperature, the recommended range is (0. 0025 -0.01 kg/sec) the inlet and outlet pressures are approximately (1-1.10 bar), and through (25- 225 watts) applied heat. The iterative process is used to obtain the heat flow characteristics, for example; the single-phase heat transfer coefficient is completely laminar flow developing, in this flow, guesses the wall temperature, guess the fluid temperature. The possible mechanism of heat transfer has been discussed

Convective Heat Transfer Investigation of a Confined Air Slot-Jet Impingement Cooling on Corrugated Surfaces With Different Wave Shapes

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Recep Ekiciler ◽  
Muhammet Samet Ali Çetinkaya ◽  
Kamil Arslan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Flow Characteristics ◽  
Jet Impingement ◽  
Working Fluid ◽  
Bottom Surface ◽  
Air Jet ◽  
Corrugated Surfaces ◽  
Energy Equations

In this study, air jet impingement on flat, triangular-corrugated, and sinusoidal-corrugated surfaces was numerically investigated. Bottom surface was subjected to constant surface temperature. Air was the working fluid. The air exited from a rectangular shaped slot and impinged on the bottom surface. The Reynolds number was changed between 125 and 500. The continuity, momentum, and energy equations were solved using the finite volume method. The effect of the shape of bottom surface on heat and flow characteristics was investigated in detail. Average and local Nusselt number were calculated for each case. It was found out that Nusselt number increases by increasing the Reynolds number. The optimum conditions were established to get much more enhancement in terms of performance evaluation criterion (PEC). It was revealed that the shape of the cooling surface (bottom wall) influences the heat transfer substantially.

Sign in / Sign up

Export Citation Format

Share Document